Sound propagation in closed test section wind tunnels suffers from reflections and diffraction, which compromise acoustic measurements. In this article, it is proved possible to improve the post-processing of phased-array microphone measurements by using an approach based on the combination of numerical acoustic simulations and beamforming. A Finite Element Method solver for the Helmholtz equation is used to model the acoustic response of the experimental facility. The simulations are compared with acoustic experiments performed at TU Delft's Low Turbulence Tunnel, using both fully reflective (baseline) and lined test sections. The solver accurately predicts the acoustic propagation from a monopole sound source at the centre of the test section to the microphones in the phased-array, for frequencies in the range 500Hz<f<2000Hz. It is shown that a (lower fidelity) geometric modelling method is unable to precisely predict the acoustic response of the Low Turbulence Tunnel at these frequencies, due to strong acoustic diffraction. The numerical results are used to implement corrections to the post-processing of experimental data. A corrected version of the Source Power Integration method is able to increase the accuracy of the source's noise levels calculation, based on a single numerical simulation with the source at the same location as in the experiment. A Green's function correction increases the beamforming resolution and the source's noise levels estimation accuracy from the beamforming maps, without a priori knowledge of the source's location. Both corrections perform well at processing flow-on acoustic measurements, and the Green's function correction shows an additional benefit. The improvement in beamforming spatial resolution leads to an increase of the signal to noise ratio.

@en

This study presents a numerical investigation of the aerodynamic and aeroacoustics behavior of side-by-side rotors in proximity to the ground. The configuration developed in the European H2020 project ENODISE is used as a reference. It features two counter-rotating APC 6x4 propellers, positioned at a height H/R = 2 above the ground, where R is the propeller radius, with a tip-to-tip distance S/R = 2, operating at a rotational speed of 167 Hz. Scale-resolved simulation is carried out using the Lattice-Boltzmann/Very-Large-Eddy-Simulation CFD solver SIMULIA PowerFLOW®. Analysis of the data describes the spatio-temporal of the flow field and describes in detail the bi-stable behavior of wake in the presence of the ground, which is then re-ingested by the rotor disks. This motion, occurring at a frequency two orders of magnitude lower than the rotor blade passing frequency, is similar to what was found experimentally. In addition, the present work shows the impact of this phenomenon on far-field noise by comparing sound pressure levels (SPL) pre- and post-re-ingestion in a semi-spherical manner. The findings reveal a significant increase in SPL across a broad frequency range as the occurrence of the re-ingestion.@en

A physical analysis has been conducted to assess the effects of turbulence distortion on leading-edge noise generation and low-fidelity modeling in the framework of Amiet's theory. This model retrieves the power spectral density (PSD) of far-field noise using as input the upwash velocity spectrum of incoming turbulent flow and an aeroacoustic transfer function modeling the aerodynamic and acoustic response of the airfoil to the perturbation. The study has been carried out by investigating the interaction of grid-generated turbulence with a NACA 0012 and a NACA 0012-103, featuring the same thickness but different leading-edge shape. The alteration of the velocity field has been shown to occur in agreement with the analytical findings of the rapid distortion theory (RDT), identifying in particular an exponential decay for the upwash-velocity component spectrum at high frequencies. The same decay is observed for the surface-pressure spectra close to the leading edge, suggesting that sound is generated by a pressure distribution induced by the altered velocity field and hence proving that turbulence-distortion effects should be included to enhance the noise-prediction accuracy of low-fidelity models. This has been further demonstrated by using as input in Amiet's model the altered upwash velocity spectrum sampled in the immediate vicinity of the leading edge: an improved prediction of the high-frequency decay is yielded, but the evident overestimation of the noise levels with respect to the results provided by the Ffowcs-Williams and Hawkings' (FWH) analogy indicates the necessity of correcting the aeroacoustic transfer function as well.@en

This study investigates the acoustic characteristics of a distributed propeller-wing system in a tractor configuration, focusing on the potential for noise reduction using the synchrophasing technique. The experimental setup features three propellers with nacelles mounted side-by-side on the leading edge of a wing, resulting in aerodynamic interference between adjacent propellers due to a tip clearance of 5% of the radius. The study investigates the acoustic impact of varying relative blade-phase angles (synchrophasing) and further explores the implications of changing the angle of attack. The findings show that synchrophasing influences noise emissions at the locations investigated, potentially amplifying or reducing noise relative to a random configuration. Moreover, these effects persist when investigating higher angles of attack. @en

The noise emission of a simplified two-wheel nose landing gear configuration featuring a detachable porous fairing is investigated by a hybrid CFD/CAA approach. The noise mitigation properties of the porous fairing are discussed and compared against two reference configurations, i.e., baseline configurations with and without a solid fairing. The time resolved flow and acoustic near field is computed by a lattice Boltzmann (LB) method with a collision step based on countable cumulants, and the noise radiation into the far field is predicted by solving a permeable surface Ffowcs Williams and Hawkings formulation. The porous material is represented by an equivalent forcing term in the LB equation based on a Forchheimer-extended Darcy model. The porous material has a deterministic geometric structure such that the modeling parameters describing the porous material properties are determined by results from a flow simulation through the resolved micro-structures in a periodic pressure drop setup. The effect of the different fairings on the flow field and the resulting acoustic far field pressure are discussed.@en

Correction Notice 1. The vertical axis ticks in the subfigures of Fig 10 should be reverted to align with the global coordinate system of the simulation domain. The updated figure is presented below. Not the one presented in the original manuscript. (Figure Presented).

@en

A solid fairing and a wire-mesh fairing consisting of very fine wires and pores are numerically and experimentally investigated for the mitigation of landing gear noise. A slightly modified LAGOON landing gear and two configurations, one equipped with a solid fairing and the other with a wire-mesh fairing, are numerically simulated using the Improved Delayed Detached-Eddy Simulation (IDDES) in combination with the Ffowcs Williams and Hawkings (FW-H) analogy. Instead of resolving the detailed flow features through the wire mesh, a recently proposed numerical model is used to represent the effect of the wire-mesh fairing. The simulated flow fields and the far-field noise spectra are validated against the experiments conducted in an anechoic wind tunnel. The superiority of the recently proposed wire-mesh model over a classical wire-mesh model in modelling both the aerodynamic and aeroacoustic effects of the wire mesh is demonstrated. Results also show that the dense wire-mesh fairing functions very similarly to the solid fairing and that significant noise can be reduced through the installation of a solid fairing or a wire-mesh fairing upstream of the landing gears. For the baseline landing gear, the torque link and the brakes are identified noise sources. With the aerodynamic penalty of a 50% increase in drag, both fairings mitigate the pressure fluctuation on the torque link and brakes, resulting in the reduction of surface noise sources. The noise directivity shows that a solid fairing or a dense wire-mesh fairing contributes to a noise reduction of 4-6 dB in all radial directions. The findings in this study pave the way for the low-noise design of aircraft landing gears.

@en

Permeable materials are a promising trailing edge noise reduction technique. The noise reduction is a result of the unsteady interaction between the two communicating boundary layers, in a process referred to as the pressure release mechanism. However, in practice the aeroacoustic performance of permeable trailing edges degrades under lifting conditions, i.e. with a pressure and velocity differential. This study aims at investigating such flow physics using the Lattice Boltzmann Method through 3DS Power FLOW. A numerical setup was created to explore the impact of velocity and pressure differentials between two communicating boundary layers and relate them to the aeroacoustic performance of porous media. The proposed numerical setup consists of two vertically stacked temporally developing channel flows separated by a porous medium (6δ × (4δ + t) × 2 δ), where δ and t are the half-channel height and the porous medium thickness respectively. The two channel flows communicate through fully resolved porous media, here, 75% porous triply periodic minimal surfaces. A large drag increase is observed for all geometries. An increase in anti-correlation between the pressure fluctuations between the channels is found to be related to a drag increase. It was concluded that the spanwise coherent turbulent structures drive the increase in drag. These structures are also affected by the geometry of the porous medium at the surface of the grazing flows. The presence of large coherent turbulent structures leads to a shift in turbulent energy scales. This is related to the modification of the wall pressure spectrum, where it was observed that less energy is present at low frequencies, whereas a peak was observed at a higher frequency. The crossover frequency is between 150Hz and 600Hz.

@en

Operating a conventional propeller at negative thrust results in the operation of positively cambered blade sections at negative angles of attack, leading to flow separation. Consequently, accurately simulating the aerodynamics of propellers operating at negative thrust poses a greater challenge than at positive thrust. This study offers a comprehensive assessment of the aerodynamic modeling capabilities of numerical methods, spanning low to high fidelity, for computing propeller performance across both positive and negative thrust regimes. Low-fidelity methods, namely, blade-element momentum and lifting line theories, effectively predict propeller performance trends at positive thrust. However, they fail to capture trends at negative thrust beyond the maximum power output point due to the neglect of three-dimensional flow effects. Both steady and unsteady Reynolds-averaged Navier–Stokes (RANS) simulations with y ⁺ < 1 perform well across both positive and negative thrust conditions, with errors below 2%for both thrust and power magnitudes near the maximum power output point. Lattice-Boltzmann very-large-eddy simulations (LB-VLESs) with y ⁺ ≤ 10 exhibit excellent agreement with experimental data with less than 1% error near the maximum power output point but with significant computational costs. Conversely, LB-VLESs with y ⁺ ≥ 15 offer a more economical approach to capture general trends with the computational cost of the same order as unsteady RANS. However, wall models introduce errors in modeling flow separation, leading to a 16% overestimation of power magnitude near the maximum power output point. The results highlight the necessity of using tools with increased fidelity levels when considering propeller operation at negative thrust compared to the conventional positive thrust regime.

@en

Using propellers in negative thrust conditions can potentially result in many benefits, such as a steeper descent, a reduced landing run, reduced community noise, energy regeneration, etc. However, the aerodynamics and aeroacoustics of propellers in this regime are not well understood. This paper presents an aeroacoustic analysis of an isolated propeller operating in both positive and negative thrust conditions, using scale-resolved lattice-Boltzmann very large eddy simulations and the Ffowcs Williams & Hawkings analogy. The propeller was operated at a constant tip Mach number so that any differences in tonal noise between positive and negative thrust conditions were due to changes in blade loading. Results showed that the flow separation around the blades in the negative thrust case led to a 2 to 6 times higher standard deviation in integrated thrust compared to the positive thrust case. The blade loading in the negative thrust case shows the amplitude of fluctuations up to 18% for inboard sections and up to 30% near the blade tip compared to the time-averaged loads. The noise in the propeller plane is 10 dB higher in the positive thrust regime than in the negative thrust regime at a given absolute thrust level of |T_C = 0.08|. The lower noise at negative thrust is caused by two factors: the lower magnitude of the negative torque compared to the positive torque at a given thrust level and the shift of the blade loading inboard in the negative thrust condition due to the stall of the blade tip. Along the propeller axis, the negative thrust regime has 13-15 dB higher noise because of the increased broadband noise generated by the flow separation. In the negative thrust case, the noise along the propeller axis (89 dB) and propeller plane (92 dB) are comparable. However, this is not the case for the propulsive case. The comparison of noise in the vicinity of the propeller plane showed that using the propellers in negative thrust conditions allows for a steeper and quieter descent compared to a conventional descent; as long as the magnitude of the negative torque produced is equal to or less than the torque required to operate the propeller in a conventional landing.@en

This paper aims to investigate, by means of Lattice-Boltzmann simulations, the flow-field and far-field noise of two co-axial co-rotating rotors operating at 3000 rpm in hover conditions. The two co-rotating configurations are made by 2×2-bladed rotors with a fixed axial separation and two different azimuthal separations Δϕ equal to 84∘ and 12∘. Isolated 2- and 4-bladed rotors, are also simulated at the same operating conditions and used as aerodynamic and aeroacoustic reference. For both Δϕ=84∘ and 12∘, the upper rotor tip vortices are accelerated downstream due to the induction from the lower rotor, avoiding blade vortex interaction (BVI). The lower rotor tip vortices convect into the wake with a lower velocity, causing BVI for Δϕ=12∘. The lower rotor shows a reduction of thrust, relative to the upper rotor, of 36% and 66% for Δϕ=84∘ and 12∘, respectively. For Δϕ=12∘, the lower blades act as a wing flap for the upper ones, increasing their thrust. The tonal noise emission for the co-rotating rotors is driven by the interference between the acoustic waves from upper and lower rotors. Because of destructive interference, the configuration Δϕ=84∘ shows a first harmonic up to 15 dB lower than Δϕ=12∘, but still 4.5 dB higher than the isolated 4-bladed rotor.@en

Eduction methods are adopted to characterize acoustic liners. In this paper, several impedance eduction techniques are compared using a numerical database obtained with scale resolved lattice-Boltzmann simulations of a reference acoustic liner in the presence or not of a grazing turbulent flow. Three impedance eduction techniques are compared: an inverse approach based on the Mode-Matching (MM) method, the straightforward method based on the Prony-like Kumaresan-Tufts (KT) algorithm, and one approach based on a minimization problem between reference measurements and the solution of the Pierce’s equation. Furthermore, the educed impedance is compared with the one obtained using local impedance measurements with the Dean’s method with virtual probes located on the entire face-sheet. Results show that impedance values obtained with the Deans’ method are highly dependent on the sampling location and that they vary largely over each cavity. Results from the eduction methods are similar amongst them with few discrepancies found for the method based on the Pierce’s equation. In particular, the highest value of resistance obtained using the Deans’ method is similar to the one obtained using the KT and MM eduction methods.@en

This paper elucidates the link between the near-wake development of a circular cylinder coated with a porous material in a low Mach-number flow and the related aerodynamic sound attenuation. It accomplishes this by formulating the cylinder flow-induced noise as a diffraction problem. The necessity for such an approach is driven by experimental evidence obtained through acoustic beamforming and particle-image-velocimetry measurements, which reveal that the dominant noise sources for a coated cylinder are not localised on the body surface but rather in the wake, specifically at the outbreak position of the shedding instability. The acoustic field at the vortex-shedding frequency can be hence modelled by considering a compact lateral quadrupole at this location and employing an exact Green's function tailored to a cylindrical geometry. Because of the diffraction of the sound waves radiated by the quadrupolar source on the cylinder surface, the resulting far-field directivity pattern resembles that of a dipole. The study demonstrates that the porous coating has the two-fold effect of decreasing the strength of the point quadrupole in the wake and moving its origin further downstream, reducing, in turn, the efficiency of the sound scattering. Consequently, the diffracted part of the acoustic field, which dominates the far-field noise for a bare cylinder in accordance with classical theory, provides a contribution that is comparable to the direct part. The results eventually indicate that quadrupolar sources must be considered to accurately predict the noise radiated from a porous-coated cylinder, even at low Mach numbers.

@en

This study analyzes the alteration undergone by turbulent eddies as they approach a propeller operating at low Reynolds number, with the purpose of investigating the resulting effects on the noise emitted by the propeller. The two mechanisms affecting turbulence distortion, the streamtube contraction and the interaction between the turbulent structures and the blade, have been investigated experimentally. The set-up consists of a propeller with a diameter of 30 cm operating at a 75% chord-based Reynolds number of 10.8 × 104 interacting with the turbulence produced by a rectangular grid. The flow behavior has been studied by particle image velocimetry (PIV) and hot-wire anemometry (HWA), while a microphone arc was installed for the acoustic analysis. The results reveal that the interaction between incoming turbulence and the propeller plays a dominant role in the alteration of turbulence with respect to the streamtube contraction. This is due to the relatively low contraction ratio of the propeller at this regime, equal, in this case, to C.R.=1.3. Turbulence characteristics are used as input for two different analytical noise-prediction models, both based on Amiet’s theory for turbulence-impingement noise. The first implements the original formulation of Amiet for propeller noise, which requires a position along the blade to be specified to define all the inputs. The second has been developed in the present work to account for the variations of the blade geometry and turbulence conditions in the radial direction. The comparison between the noise predictions and the experimental measurements shows that a better agreement can be obtained with the second model. This reveals that noise generation is strongly dependent on the variation of the flow conditions and propeller geometry along the radial direction, confirming that the description of these characteristics can enhance the accuracy of low-fidelity noise-prediction methods.

@en

This study investigates the impact of struts and a central tower on the aerodynamics and aeroacoustics of Darrieus Vertical Axis Wind Turbines (VAWTs) at chord-based Reynolds numbers of 8.12 × 104. A 2-bladed H-Darrieus VAWT is used, featuring a 1.5m diameter, a solidity of 0.1 and a blade cross-section of symmetrical NACA 0021. The turbine design is kept simple and straight-bladed which is essential for isolating and analyzing the specific effects of struts and a tower. The high-fidelity Lattice Boltzmann Method (LBM) in PowerFLOW 6-2020 and the mid-fidelity Lifting Line Free Vortex Wake (LLFVW) method in QBlade 2.0 are employed, with the mid-fidelity method providing a faster analytical tool for insights into the turbine performance. Firstly, both the LLFVW (mid-fidelity) and LBM (high-fidelity) methods effectively capture the general trends observed in VAWT power performance. However, the former predicts mean thrust values that are approximately 10% higher, and mean torque values that are approximately 19% higher, in comparison to the latter. Subsequently, the former predicts lower streamwise wake velocities relative to those predicted by the latter. These differences increase in configurations that include struts and a tower (to 30% - 31%). Secondly, the presence of struts and a tower leads to a reduction in both mean power (by 15% to 55%) and thrust (by 3% to 3.6%), with a further small decrease observed when doubling the tower diameter (power and thrust both by 0.5% to 3%). The struts predominantly affect the spanwise distribution of blade loading, while the tower impacts the azimuthal variation of blade loading. Additionally, the addition of struts and a tower reduces low-frequency noise (50-200 Hz) while increasing high-frequency noise (> 300 Hz). The observed decrease in mean blade loading results in reduced low-frequency noise, while the increase in high-frequency noise is ascribed to the increased intensity of BWI/BVI leading to higher unsteady loading fluctuations on blades.

@en

Two passive add-on porous fairings, comprised of diamond grids varying in size, are numerically and experimentally investigated for their effectiveness in mitigating landing gear noise. The baseline landing gear, a modified version of the LAGOON landing gear with its inner rim cavities closed, along with two configurations equipped with diamond-lattice fairings, are numerically simulated using the Improved Delayed Detached-Eddy Simulation (IDDES) in combination with the Ffowcs Williams and Hawkings (FW-H) analogy. Instead of resolving the detailed flow features through the diamond-lattice fairings, a numerical model is employed to represent the effect of fairing. Prior to integrating the numerical model into the simulations of landing gears, rigorous validation of the model against experimental data in a channel flow is performed. Subsequently, the predicted flow fields and far-field noise spectra of the baseline and controlled landing gears are validated against the experiments conducted in the anechoic A-Tunnel at Delft University of Technology. The results indicate that implementing a diamond-lattice fairing upstream of the landing gear can effectively diminish far-field noise in the frequency range exceeding 200 Hz. For the baseline landing gear, the torque link and brakes are potent noise sources. For the controlled landing gears, both diamond-lattice fairings mitigate the pressure fluctuations on the torque link and brakes, leading to a reduction of surface noise sources. The noise directivity shows that the DL 4.5mm fairing produces a noise reduction of 2-6 dB whereas the DL 2.5mm fairing generates a noise reduction of 3-7 dB across all radial directions. These findings pave the way for the low-noise design of aircraft landing gears.@en

Motivated by the potential benefit of Strut-Braced Wing (SBW) configurations in reducing fuel burn, this manuscript investigates the noise generated by the interaction between the propeller slipstream and the SBW. The flow field on a regional transport aircraft is computed in high-lift condition by means of a high-fidelity Lattice Boltzmann solver with very large eddy simulation approach. The acoustic far field is obtained using the Ffowcs-Williams and Hawkings acoustic analogy. The analysis shows that the main aeroacoustic effect due to the interaction between the SBW and the propeller slipstream is the emergency of a tonal noise scattering from the region bounded by the pressure side of the main wing and the suction side of the strut at twice the blade passing frequency.@en

This study investigates the aerodynamic and acoustic response of a multi-orifice acoustic liner grazed by a planar acoustic wave and turbulent flow, at centerline Mach number equal to 0.32. High-fidelity flow simulations are carried out using a Lattice-Boltzmann Very-LargeEddy-Simulation solver and the in-situ technique is used to calculate impedance. The triple decomposition technique is adopted to separate the mean-flow effects from those due to grazing tonal acoustic waves with different frequencies and amplitudes. This study highlights the sensitivity of in-situ measurements on the position of the face-sheet probe used to sample the unsteady pressure fluctuations. It is found that the resistance changes up to a factor of three along each cavity. The acoustic-induced velocity field reveals the intricate interaction between the acoustic waves and the turbulent flow. It is shown that the wake shed by the upstream cavity impacts the downstream one, affecting the spatial distribution and the amplitude of the acoustic-induced velocity within the orifice. Furthermore, a vortex within the hole is observed; it is found that its impact on resistance depends on the acoustic wave propagation with respect to the mean flow.

@en

In this paper, the feasibility of using far-field acoustic measurements as a non-contact monitoring technique for wind turbine blade leading edge erosion is assessed. For this purpose, a DU96 W180 airfoil with several eroded leading edge configurations of different severities is experimentally investigated. The eroded leading edges are designed with pits, gouges and coating delamination scaled from a real eroded blade. To assess the feasibility of the technique in quasi-realistic configurations, experiments are carried out under clean and turbulent inflow conditions. Acoustic measurements are performed with a phased microphone array. In the absence of inflow turbulence, because of the low Reynolds number at which the experiments are carried out, the case with minor erosion severity shows similar far-field noise spectra as the clean leading-edge cases, i.e., the presence of tonal peaks caused by laminar boundary layer instability noise through a self-sustained feedback loop but with higher tonal amplitudes. Increasing the damage level (considered as moderate erosion), the spectra of the noise scattered from the suction side show that the tonal peaks shift to higher frequencies and have lower amplitudes, thus suggesting that the damage alters the flow features responsible for the acoustic feedback loop; whereas, the spectra from the pressure side show a broadband noise distribution. For heavy erosion, the far-field noise spectra show broadband features from both airfoil sides, thus suggesting that the damage has fully forced the transition to turbulent flow; in which case, an increase in the low-frequency content is observed. Conversely, in the presence of turbulent inflow, when comparing the noise scattered at the trailing edge, no difference is found. However, leading edge impingement noise decreases at medium–high frequency compared with the baseline case at a chord-length-based Strouhal number St_C~10. The experimental results also suggest that the delamination feature is the one which is the most easily detectable and the approach is valid for a wide range of angles of attack and inflow velocity.@en

The present study assesses the ability to numerically predict turbulence-interaction noise of a NACA0012 airfoil with grid-generated turbulence by utilizing the Lattice Boltzmann solver PowerFLOW. Both the near-field flow characteristics and far field noise are bench-marked against an existing experimental study. The grid was chosen to match that from the experiment to provide evidence that the present numerical approach in physically placing a grid upstream of the airfoil can reproduce the turbulence characteristics observed from the benchmark experiment and thus accurately capture the turbulence-interaction noise generated. The comparison of the results show that the turbulence statistics, including turbulence intensity, integral length scales and anisotropy are highly consistent with the experiment. Moreover, far field acoustics of the turbulence interaction as well as the near-field flow properties near the leading-edge and the unsteady wall pressure fluctuations of the airfoil are also analyzed and the results agreed well with the experimental measurements. The present study confirms that the grid-generated approach is suitable for numerical investigation of turbulence-interaction noise and its potential mitigation strategies.@en