Background/Objectives: “Hermes” is an ankle–foot orthosis (AFO) with negative stiffness designed to mechanically compensate the symptomatic increase in plantarflexion (PF) torque (i.e., ankle joint torque resistance to dorsiflexion, DF) in patients with spastic paresis.
Methods: The effectiveness of “Hermes” was evaluated in twelve patients with chronic unilateral spastic paresis after stroke. Using a robotic ankle manipulator, stiffness at the ankle joint was assessed across three conditions: ankle without Hermes (𝐴), ankle with Hermes applying no torque compensation (𝐴+𝐻0%), and ankle with Hermes tuned to compensate 100% of the patients’ ankle joint stiffness (𝐴+𝐻100%).
Results: A significant reduction in PF torque was found with Hermes applying compensation (𝐴+𝐻100%) compared to the conditions without Hermes (𝐴) and with Hermes applying no compensation (𝐴+𝐻0%). Furthermore, a significant reduction in positive dorsiflexion work was found with Hermes applying compensation (𝐴+𝐻100%) compared to the condition with Hermes applying no compensation (𝐴+𝐻0%). Hermes did not significantly contribute to additional PF torque or positive work when applying no compensation (𝐴+𝐻0%).
Conclusions: The reductions in PF torque achieved with Hermes are comparable to those seen with repeated ankle stretching programs and ankle robot training. Thus, Hermes is expected to assist voluntary dorsiflexion and improve walking in patients with spastic paresis.@en

While shoulder injuries resulting from the bench press exercise are commonly reported, no biomechanical evidence for lowering injury risk is currently available. Therefore, the aim of the present study was to compare musculoskeletal shoulder loads and potential injury risk during several bench press variations. Ten experienced strength athletes performed 21 technical variations of the barbell bench press, including variations in grip width of 1,1.5 and 2 bi-acromial widths (BAW), shoulder abduction angles of 45°, 70° and 90°, and scapula poses including neutral, retracted, and released conditions. Motions and forces were recorded by an opto-electronic measurement system and an instrumented barbell. An OpenSim musculoskeletal shoulder model was employed to estimate joint reaction forces in the glenohumeral and acromioclavicular joints. Time-series of joint reaction forces were compared between techniques by statistical non-parametric mapping. Results showed that narrower grip widths of <1.5 BAW decreased acromioclavicular compression (p < 0.05), which may decrease the risk for distal clavicular osteolysis. Moreover, scapula retraction, as well as a grip width of <1.5 BAW (p < 0.05), decreased glenohumeral posterior shear force components and rotator cuff activity and may decrease the risk for glenohumeral instability and rotator cuff injuries. Furthermore, results showed that mediolaterally exerted barbell force components varied considerably between athletes and largely affected shoulder reaction forces. It can be concluded that the grip width, scapula pose and mediolateral exerted barbell forces during the bench press influence musculoskeletal shoulder loads and the potential injury risk. Results of this study can contribute to safer bench press training guidelines.@en

Background: Amyotrophic lateral sclerosis (ALS) is a lethal progressive neurodegenerative disease characterized by upper motor neuron (UMN) and lower motor neuron (LMN) involvement. Their varying degree of involvement results in a clinical heterogenous picture, making clinical assessments of UMN signs in patients with ALS often challenging. We therefore explored whether instrumented assessment using robotic manipulation could potentially be a valuable tool to study signs of UMN involvement. Methods: We examined the dynamics of the wrist joint of 15 patients with ALS and 15 healthy controls using a Wristalyzer single-axis robotic manipulator and electromyography (EMG) recordings in the flexor and extensor muscles in the forearm. Multi-sinusoidal torque perturbations were applied, during which participants were asked to either relax, comply or resist. A neuromuscular model was used to study muscle viscoelasticity, e.g. stiffness (k) and viscosity (b), and reflexive properties, such as velocity, position and force feedback gains (kv, kp and kf, respectively) that dominated the responses. We further obtained clinical signs of LMN (muscle strength) and UMN (e.g. reflexes, spasticity) dysfunction, and evaluated their relation with the estimated neuromuscular model parameters. Results: Only force feedback gains (kf) were elevated in patients (p = 0.033) compared to controls. Higher kf, as well as the resulting reflexive torque (Tref), were both associated with more severe UMN dysfunction in the examined arm (p = 0.040 and p < 0.001). Patients with UMN symptoms in the examined arm had increased kf and Tref compared to controls (both p = 0.037). Neither of these measures was related to muscle strength, but muscle stiffness (k) was lower in weaker patients (p = 0.012). All these findings were obtained from the relaxed test. No differences were observed during the instructions comply and resist. Conclusions: This findings are proof-of-concept that instrumented assessment using robotic manipulation is a feasible technique in ALS, which may provide quantitative, operator-independent measures relating to UMN symptoms. Elevated force feedback gains, driving larger reflexive muscle torques, appear to be particularly indicative of clinically established levels of UMN dysfunction in the examined arm.

@en

Individuals with an upper motor neuron syndrome, e.g., stroke survivors, may have a pathological increase of passive ankle stiffness due to spasticity, that impairs ankle function and activities such as walking. To improve mobility, walking aids such as ankle-foot orthoses and orthopaedic shoes are prescribed. However, these walking aids generally limit the range of motion (ROM) of the foot and may therewith negatively influence activities that require a larger ROM. Here we present a new ankle-foot orthosis 'Hermes', and its first experimental results from four hemiparetic chronic stroke patients. Hermes was designed to facilitate active ankle dorsiflexion by mechanically compensating the passive ankle stiffness using a negative-stiffness mechanism. Four levels of the Hermes' stiffness compensation (0%, 35%, 70% and 100%) were applied to evaluate active ROM in a robotic ankle manipulator and to test walking feasibility on an instrumented treadmill, in a single session. The robotic tests showed that Hermes successfully compensated the ankle joint stiffness in all four patients and improved the active dorsiflexion ROM in three patients. Three patients were able to walk with Hermes at one or more Hermes' stiffness compensation levels and without reducing their preferred walking speeds compared to those with their own walking aids. Despite a small sample size, the results show that Hermes holds great promise to support voluntary ankle function and to benefit walking and daily activities.

@en

Muscle overload injuries in strength training might be prevented by providing personalized feedback about muscle load during a workout. In the present study, a new muscle load feedback application, which monitors and visualizes the loading of specific muscle groups, was developed in collaboration with the fitness company Gymstory. The aim of the present study was to examine the effectiveness of this feedback application in managing muscle load balance, muscle load level, and muscle soreness, and to evaluate how its actual use was experienced. Thirty participants were randomly distributed into ‘control’, ‘partial feedback’, and ‘complete feedback’ groups and monitored for eight workouts using the automatic exercise tracking system of Gymstory. The control group received no feedback, while the partial feedback group received a visualization of their estimated cumulative muscle load after each exercise, and the participants in the complete feedback group received this visualization together with suggestions for the next exercise to target muscle groups that had not been loaded yet. Generalized estimation equations (GEEs) were used to compare muscle load balance and soreness, and a one-way ANOVA was used to compare user experience scores between groups. The complete feedback group showed a significantly better muscle load balance (β = −18.9; 95% CI [−29.3, −8.6]), adhered better to the load suggestion provided by the application (significant interactions), and had higher user experience scores for Attractiveness (p = 0.036), Stimulation (p = 0.031), and Novelty (p = 0.019) than the control group. No significant group differences were found for muscle soreness. Based on these results, it was concluded that personal feedback about muscle load in the form of a muscle body map in combination with exercise suggestions can effectively guide strength training practitioners towards certain load levels and more balanced cumulative muscle loads. This application has potential to be applied in strength training practice as a training tool and may help in preventing muscle overload.@en

Fall risk increases with age, and one-third of adults over 65 years old experience a fall annually. Due to the aging population, the number of falls and related medical costs will progressively increase. Correct prediction of who will fall in the future is necessary to timely intervene in order to prevent falls. Therefore, the aim of this scoping review is to determine the predictive value of fall risk assessments in community-dwelling older adults using prospective studies. A total of 37 studies were included that evaluated clinical assessments (questionnaires, physical assessments, or a combination), sensor-based clinical assessments, or sensor- based daily life assessments using prospective study designs. The posttest probability of falling or not falling was calculated. In general, fallers were better classified than non-fallers. Questionnaires had a lower predictive capability compared to the other assessment types. Contrary to conclusions drawn in reviews that include retrospective studies, the predictive value of physical tests evaluated in prospective studies varies largely, with only smaller-sampled studies showing good predictive capabilities. Sensor-based fall risk assessments are promising and improve with task complexity, although they have only been evaluated in relatively small samples. In conclusion, fall risk prediction using sensor data seems to outperform conventional tests, but the method’s validity needs to be confirmed by large prospective studies.@en

Autonomous robots are used to inspect, repair and maintain underwater assets. These tasks require energy-efficient robots, including efficient movement to extend available operational time. To examine the suitability of a propulsion system based on undulating fins, we built two robots with one and two fins, respectively, and conducted a parametric study for combinations of frequency, amplitude, wavenumber and fin shapes in free-swimming experiments, measuring steady-state swimming speed, power consumption and cost of transport. The following trends emerged for both robots. Swimming speed was more strongly affected by frequency than amplitude across the examined wavenumbers and fin heights. Power consumption was sensitive to frequency at low wavenumbers, and increasingly sensitive to amplitude at high wavenumbers. This increasing sensitivity of amplitude was more pronounced in tall rather than short fins. Cost of transport showed a complex relation with fin size and kinematics and changed drastically across the mapped parameter space. At equal fin kinematics as the single-finned robot, the double-finned robot swam slightly faster (>10%) with slightly lower power consumption (<20%) and cost of transport (<40%). Overall, the robots perform similarly to finned biological swimmers and other bio-inspired robots, but do not outperform robots with conventional propulsion systems.

@en

Human hands are complex biomechanical systems that allow for dexterous tasks with many degrees of freedom. Coordination of the fingers is essential for many activities of daily living and involves integrating sensory signals. During this sensory integration, the central nervous system deals with the uncertainty of sensory signals. When handling compliant objects, force and position are related. Interactions with stiff objects result in reduced position changes and increased force changes compared to compliant objects. Literature has shown sensory integration of force and position at the shoulder. Nevertheless, differences in sensory requirements between proximal and distal joints may lead to different proprioceptive representations, hence findings at proximal joints cannot be directly transferred to distal joints, such as the digits. Here, we investigate the sensory integration of force and position during pinching. A haptic manipulator rendered a virtual spring with adjustable stiffness between the index finger and the thumb. Participants had to blindly reproduce a force against the spring. In both visual reference trials and blind reproduction trials, the relation between pinch force and spring compression was constant. However, by covertly changing the spring characteristics in catch trials into an adjusted force-position relation, the participants’ weighting of force and position could be revealed. In agreement with previous studies on the shoulder, participants relied more on force sense in trials with higher stiffness. This study demonstrated stiffness-dependent sensory integration of force and position feedback during pinching.

@en

In baseball pitchers the elbow is exposed to high and repetitive loads (i.e. external valgus torque), caused by pitching a high number of balls in a practice session or game. This can result in overuse injuries like the ulnar collateral ligament (UCL) injury. To understand injury mechanisms, the effect of repetitive pitching on the elbow load magnitude and variability was investigated. In addition, we explored whether repetitive pitching affects elbow muscle activation during pitching. Fifteen pitchers threw each 60 to 110 balls. The external valgus torque and electromyography of three elbow muscles were quantified during each pitch. Linear mixed model analyses were performed to investigate the effect of repetitive pitching. On a group level, the linear mixed models showed no significant associations of repetitive pitching with valgus torque magnitude and variability and elbow muscle activity. Significant differences exist between pitchers in their individual trajectories in elbow valgus torque and muscle activity with repetitive pitching. This shows the importance of individuality in relation to repetitive pitching. In order to achieve effective elbow injury prevention in baseball pitching, individual characteristics of changes in elbow load and muscle activity in relation to the development of UCL injuries should be investigated.

@en

Transcranial direct current stimulation (tDCS) is a promising tool to improve and speed up motor rehabilitation after stroke, but inconsistent clinical effects refrain tDCS from clinical implementation. Therefore, this study aimed to assess the need for individualized tDCS configurations in stroke, considering interindividual variability in brain anatomy and motor function representation. We simulated tDCS in individualized MRI-based finite element head models of 21 chronic stroke subjects and 10 healthy age-matched controls. An anatomy-based stimulation target, i.e. the motor hand knob, was identified with MRI, whereas a motor function-based stimulation target was identified with EEG. For each subject, we simulated conventional anodal tDCS electrode configurations and optimized electrode configurations to maximize stimulation strength within the anatomical and functional target. The normal component of the electric field was extracted and compared between subjects with stroke and healthy, age-matched controls, for both targets, during conventional and optimized tDCS. Electrical field strength was significantly lower, more variable and more frequently in opposite polarity for subjects with stroke compared to healthy age-matched subjects, both for the anatomical and functional target with conventional, i.e. non-individualized, electrode configurations. Optimized, i.e. individualized, electrode configurations increased the electrical field strength in the anatomical and functional target for subjects with stroke but did not reach the same levels as in healthy subjects. Considering individual brain structure and motor function is crucial for applying tDCS in subjects with stroke. Lack of individualized tDCS configurations in subjects with stroke results in lower electric fields in stimulation targets, which may partially explain the inconsistent clinical effects of tDCS in stroke trials.

@en

Background: Inertial measurement units (IMUs) offer the possibility to capture the lower body motions of players of outdoor team sports. However, various sources of error are present when using IMUs: the definition of the body frames, the soft tissue artefact (STA) and the orientation filter. Methods to minimize these errors are currently being used without knowing their exact influence on the various sources of errors. The goal of this study was to present a method to quantify each of the sources of error of an IMU separately. Methods: An optoelectronic system was used as a gold standard. Rigid marker clusters (RMCs) were designed to construct a rigid connection between the IMU and four markers. This allowed for the separate quantification of each of the sources of error. Ten subjects performed nine different football-specific movements, varying both in the type of movement, and in movement intensity. Results: The error of the definition of the body frames (11.3–18.7 deg RMSD), the STA (3.8–9.1 deg RMSD) and the error of the orientation filter (3.0–12.7 deg RMSD) were all quantified separately for each body segment. Conclusions: The error sources of IMU-based motion analysis were quantified separately. This allows future studies to quantify and optimize the effects of error reduction techniques.

@en

Markerless estimation of 3D Kinematics has the great potential to clinically diagnose and monitor movement disorders without referrals to expensive motion capture labs; however, current approaches are limited by performing multiple de-coupled steps to estimate the kinematics of a person from videos. Most current techniques work in a multi-step approach by first detecting the pose of the body and then fitting a musculoskeletal model to the data for accurate kinematic estimation. Errors in training data of the pose detection algorithms, model scaling, as well the requirement of multiple cameras limit the use of these techniques in a clinical setting. Our goal is to pave the way toward fast, easily applicable and accurate 3D kinematic estimation . To this end, we propose a novel approach for direct 3D human kinematic estimation D3KE from videos using deep neural networks. Our experiments demonstrate that the proposed end-to-end training is robust and outperforms 2D and 3D markerless motion capture based kinematic estimation pipelines in terms of joint angles error by a large margin (35% from 5.44 to 3.54 degrees). We show that D3KE is superior to the multi-step approach and can run at video framerate speeds. This technology shows the potential for clinical analysis from mobile devices in the future. @en

Medial elbow overuse injuries are rising in baseball. The external valgus torque magnitude is a possible risk factor for medial elbow injuries. The magnitude on its own cannot explain why one pitcher sustains an injury and another does not. Therefore, the aim of this study is to describe the within-individual external valgus torque variability and to determine whether the within-individual external valgus torque variability can be described by a Gaussian distribution. Eleven youth elite baseball pitchers threw twenty-five fastball pitches. Body kinematics were measured with VICON motion capture at 400 Hz. Elbow valgus torques of the total 270 pitches were calculated with a custom-made inverse dynamic model in Python. Visual inspection and the Shapiro–Wilk test were performed to test for the within-individual elbow valgus torque normality. The results showed that within-individual valgus torque variability was present in pitchers and differed among pitchers. Furthermore, it was shown that the within-individual valgus torque variability was normally distributed in nine out of eleven subjects. In conclusion, the presence of and differences in within-individual elbow load variability among baseball pitchers can be useful variables as they might be related to overuse elbow injuries. @en

Muscle force analysis can be essential for injury risk estimation and performance enhancement in sports like strength training. However, current methods to record muscle forces including electromyography or marker-based measurements combined with a musculoskeletal model are time-consuming and restrict the athlete's natural movement due to equipment attachment. Therefore, the feasibility and validity of a more applicable method, requiring only a single standard camera for the recordings, combined with a deep-learning model and musculoskeletal model is evaluated in the present study during upper-body strength exercises performed by five athletes. Comparison of muscle forces obtained by the single camera driven model against those obtained from a state-of-the art marker-based driven musculoskeletal model revealed strong to excellent correlations and reasonable RMSD's of 0.4–2.1% of the maximum force (Fmax) for prime movers, and weak to strong correlations with RMSD's of 0.4–0.7% Fmax for stabilizing and secondary muscles. In conclusion, a single camera deep-learning driven model is a feasible method for muscle force analysis in a strength training environment, and first validity results show reasonable accuracies, especially for prime mover muscle forces. However, it is evident that future research should investigate this method for a larger sample size and for multiple exercises.

@en

Recent studies have established the presence of nociceptive steady-state evoked potentials (SSEPs), generated in response to thermal or intra-epidermal electric stimuli. This study explores cortical sources and generation mechanisms of nociceptive SSEPs in response to intra-epidermal electric stimuli. Our method was to stimulate healthy volunteers (n = 22, all men) with 100 intra-epidermal pulse sequences. Each sequence had a duration of 8.5 s, and consisted of pulses with a pulse rate between 20 and 200 Hz, which was frequency modulated with a multisine waveform of 3, 7 and 13 Hz (n = 10, 1 excluded) or 3 and 7 Hz (n = 12, 1 excluded). As a result, evoked potentials in response to stimulation onset and contralateral SSEPs at 3 and 7 Hz were observed. The SSEPs at 3 and 7 Hz had an average time delay of 137 ms and 143 ms respectively. The evoked potential in response to stimulation onset had a contralateral minimum (N1) at 115 ms and a central maximum (P2) at 300 ms. Sources for the multisine SSEP at 3 and 7 Hz were found through beamforming near the primary and secondary somatosensory cortex. Sources for the N1 were found near the primary and secondary somatosensory cortex. Sources for the N2-P2 were found near the supplementary motor area. Harmonic and intermodulation frequencies in the SSEP power spectrum remained below a detectable level and no evidence for nonlinearity of nociceptive processing, i.e. processing of peripheral firing rate into cortical evoked potentials, was found.

@en

Background: Baseball pitching is associated with a high prevalence of ulnar collateral ligament injuries, potentially due to the high external valgus load on the medial side of the elbow at the instant of maximal shoulder external rotation (MER). In-vitro studies show that external valgus torque is resisted by the ulnar collateral ligament but could also be compensated by elbow muscles. As the potential active contribution of these muscles in counteracting external valgus load during baseball pitching is unknown, the aim of this study is to determine whether and to what extent the elbow muscles are active at and around MER during a fastball pitch in baseball.

Methods: Eleven uninjured pitchers threw 15 fastball pitches. Surface electromyography of six muscles crossing the elbow were measured at 2000 Hz. Electromyography signals were normalized to maximal activity values. Co-contraction index (CCI) was calculated between two pairs of the flexor and extensor elbow muscles. Confidence intervals were calculated at the instant of MER. Four ranges of muscle activity were considered; 0–20% was considered low; 21–40% moderate; 41–60% high and over 60% as very high. To determine MER, the pitching motion was captured with a highspeed camera at 240 Hz.

Results: The flexor pronator mass, pronator teres, triceps brachii, biceps brachii, extensor supinator mass and anconeus show moderate activity at MER. Considerable variation between participants was found in all muscles. The CCI revealed co-contraction of the two flexor-extensor muscle pairs at MER.

Interpretation: The muscle activation of the flexor and pronator muscles at MER indicates a direct contribution of forearm muscles crossing the medial side of the elbow in counteracting the external valgus load during fastball pitching. The activation of both flexor and extensor muscles indicates an in-direct contributory effect as the combined activity of these muscles counteract opening of the humeroulnar joint space. We believe that active muscular contributions counteracting the elbow valgus torque can be presumed to relieve the ulnar collateral ligament from maximal stress and are thus of importance in injury risk assessment in fastball pitching in baseball.@en

Motion capture systems are extensively used to track human movement to study healthy and pathological movements, allowing for objective diagnosis and effective therapy of conditions that affect our motor system. Current motion capture systems typically require marker placements which is cumbersome and can lead to contrived movements.Here, we describe and evaluate our developed markerless and modular multi-camera motion capture system to record human movements in 3D. The system consists of several interconnected single-board microcomputers, each coupled to a camera (i.e., the camera modules), and one additional microcomputer, which acts as the controller. The system allows for integration with upcoming machine-learning techniques, such as DeepLabCut and AniPose. These tools convert the video frames into virtual marker trajectories and provide input for further biomechanical analysis.The system obtains a frame rate of 40 Hz with a sub-millisecond synchronization between the camera modules. We evaluated the system by recording index finger movement using six camera modules. The recordings were converted via trajectories of the bony segments into finger joint angles. The retrieved finger joint angles were compared to a marker-based system resulting in a root-mean-square error of 7.5 degrees difference for a full range metacarpophalangeal joint motion.Our system allows for out-of-the-lab motion capture studies while eliminating the need for reflective markers. The setup is modular by design, enabling various configurations for both coarse and fine movement studies, allowing for machine learning integration to automatically label the data. Although we compared our system for a small movement, this method can also be extended to full-body experiments in larger volumes.

@en

PURPOSE: Neuromuscular fatigue is considered to be important in the etiology of hamstring strain injuries in football. Fatigue is assumed to lead to decreases in hamstring contractile strength and changes in sprinting kinematics, which would increase hamstring strain injury risk. Therefore, the aim was to examine the effects of football-specific fatigue on hamstring maximal voluntary torque (MVT) and rate of torque development (RTD), in relation to alterations in sprinting kinematics. METHODS: Ten amateur football players executed a 90-min running-based football match simulation. Before and after every 15 min of simulated play, MVT and RTD of the hamstrings were obtained in addition to the performance and lower body kinematics during a 20-m maximal sprint. Linear mixed models and repeated measurement correlations were used to assess changes over time and common within participant associations between hamstring contractile properties and peak knee extension during the final part of the swing phase, peak hip flexion, peak combined knee extension and hip flexion, and peak joint angular velocities, respectively. RESULTS: Hamstring MVT and sprint performance were significantly reduced by 7.5% and 14.3% at the end of the football match simulation. Unexpectedly, there were no indications for reductions in RTD when MVT decrease was considered. Decreases in hamstring MVT were significantly correlated to decreases in peak knee angle (R = 0.342) and to increases in the peak combined angle (R = -0.251). CONCLUSIONS: During a football match simulation, maximal voluntary isometric hamstring torque declines. This decline is related to greater peak knee extension and peak combined angle during sprint running, which indicates a reduced capacity of the hamstrings to decelerate the lower leg during sprint running with fatigue.

@en

Background: Proprioception is important for regaining motor function in the paretic upper extremity after stroke. However, clinical assessments of proprioception are subjective and require verbal responses from the patient to applied proprioceptive stimuli. Cortical responses evoked by robotic wrist perturbations and measured by electroencephalography (EEG) may be an objective method to support current clinical assessments of proprioception. Objective: To establish whether evoked cortical responses reflect proprioceptive deficits as assessed by clinical scales and whether they predict upper extremity motor function at 26 weeks after stroke. Methods: Thirty-one patients with stroke were included. In week 1, 3, 5, 12, and 26 after stroke, the upper extremity sections of the Erasmus modified Nottingham Sensory Assessment (EmNSA-UE) and the Fugl-Meyer Motor Assessment (FM-UE) and the EEG responses (64 channels) to robotic wrist perturbations were measured. The extent to which proprioceptive input was conveyed to the affected hemisphere was estimated by the signal-to-noise ratio (SNR) of the evoked response. The relationships between SNR and EmNSA-UE as well as SNR and time after stroke were investigated using linear regression. Receiver-operating-characteristic curves were used to compare the predictive values of SNR and EmNSA-UE for predicting whether patients regained some selective motor control (FM-UE > 22) or whether they could only move their paretic upper extremity within basic limb synergies (FM-UE ≤ 22) at 26 weeks after stroke. Results: Patients (N = 7) with impaired proprioception (EmNSA-UE proprioception score < 8) had significantly smaller SNR than patients with unimpaired proprioception (N = 24) [EmNSA-UE proprioception score = 8, t(29) = 2.36, p = 0.03]. No significant effect of time after stroke on SNR was observed. Furthermore, there was no significant difference in the predictive value between EmNSA-UE and SNR for predicting motor function at 26 weeks after stroke. Conclusion: The SNR of the evoked cortical response does not significantly change as a function of time after stroke and differs between patients with clinically assessed impaired and unimpaired proprioception, suggesting that SNR reflects persistent damage to proprioceptive pathways. A similar predictive value with respect to EmNSA-UE suggests that SNR may be used as an objective predictor next to clinical sensory assessments for predicting motor function at 26 weeks after stroke.

@en

A sustained sensory stimulus with a periodic variation of intensity creates an electrophysiological brain response at associated frequencies, referred to as the steady-state evoked potential (SSEP). The SSEPs elicited by the periodic stimulation of nociceptors in the skin may represent activity of a brain network that is primarily involved in nociceptive processing. Exploring the behavior of this network could lead to valuable insights regarding the pathway from nociceptive stimulus to pain perception. We present a method to directly modulate the pulse rate of nociceptive afferents in the skin with a multisine waveform through intra-epidermal electric stimulation. The technique was demonstrated in healthy volunteers. Each subject was stimulated using a pulse sequence modulated by a multisine waveform of 3, 7 and 13 Hz. The EEG was analyzed for the presence of the base frequencies and associated (sub)harmonics. Topographies showed significant central and contralateral SSEP responses at 3, 7 and 13 Hz in respectively 7, 4 and 3 out of the 9 participants included for analysis. As such, we found that intra-epidermal stimulation with a multisine frequency modulated pulse sequence can generate nociceptive SSEPs. The possibility to stimulate the nociceptive system using multisine frequency modulated pulses offers novel opportunities to study the temporal dynamics of nociceptive processing.

@en