Image based three-dimensional (3D) particle tracking is currently the most widely used technique for volumetric velocity measurements. Inspecting the flow-field around an object is however, hampered by the latter, obstructing the view across it. In this study, the problem of measurement limitations due to the above is addressed. The present work builds upon the recent proposal from Wieneke and Rockstroh (2024 Meas. Sci. Technol. 35 055303), whereby the information of the occluded lines of sight can be incorporated into the particle tracking algorithm. The approach, however, necessitates methods that accurately evaluate the shape and position of the object within the measurement domain. Methods of object marking and the following 3D registration of a digital object model (CAD) are discussed. For the latter, the iterative closest point registration algorithm is adopted. The accuracy of object registration is evaluated by means of experiments, where marking approaches that include physical and optically projected markers are discussed and compared. Three objects with growing level of geometrical complexity are considered: a cube, a truncated wing and a scaled model of a sport cyclist. The registered CAD representations of the physical objects are included in aerodynamic experiments, and the flow field is measured by means of large-scale particle tracking using helium filled soap bubbles. Results indicate that object registration enables a correct reconstruction of flow tracers within regions otherwise affected by domain clipping as a consequence of obstructed camera lines-of-sight. Finally, the combined visualization of the object and the surrounding flow pattern offers means of insightful data inspection and interpretation, along with posing a basis for particle image velocimetry data assimilation at the fluid-solid interface.

@en

As of present the Urban Air Mobility market has been dominated by fully electric aircraft. However, hydrogen vehicles have remained relatively undeveloped in this segment, also because hydrogen poses additional design complexities and uncertainties concerning crashworthiness, fuel cell cooling, and low volumetric density. Nevertheless, hydrogen might yield advantages in mission performance owing to its superior gravimetric energy density and greater sustainability when compared to batteries. In this paper, the design procedure of a four-passenger long-range hydrogen eVTOL using Multidisciplinary Analysis and Design Optimization (MADO) is presented. Using MADO, the mission energy of the eVTOL was minimized while abiding by the constraints rooting from the use of hydrogen. Based on this design, the conclusion can be made that the implementation of hydrogen eVTOLs in urban air mobility is feasible whilst taking into account constraints resulting from the use of hydrogen at the preliminary design stage. This led to an aircraft which excels at longer range due to the increased scalability of hydrogen fuel, but having a weight penalty due to auxiliary equipment which hampers its performance and results in a large fuselage and maximum takeoff weight.@en

We investigate the impact of a single miniature Helmholtz resonator on wall-bounded turbulence using time-resolved planar particle image velocimetry. A particular aim is to explain the mechanism by which a resonator alters the turbulent velocity fluctuations of different scales. A grazing flow configuration is studied in which the resonator is embedded in the wall beneath a turbulent boundary layer at a friction Reynolds number of Reτ≈2300; the resonator is designed so that its resonance frequency matches the peak frequency of the wall-pressure spectrum. It is found that the resonator amplifies velocity fluctuations near its resonance frequency, while it attenuates the energy of subresonance scales. Underlying mechanisms responsible for these changes in energy are discussed in view of the resonator's local impedance condition. It is posited that large-scale velocity fluctuations in the wall-normal velocity, at temporal frequencies below resonance, are subject to a phase-opposed wall-normal velocity perturbation when the TBL flow convects over the resonator's orifice. This yields a decrease of large-scale energy in u′u′¯,-u′v′¯, and v′v′¯. In addition, modifications of the wall-shear stress field downstream of the resonator are addressed. Insights from this research will contribute to the development of surface designs for passive skin-friction control using arrays of miniature resonators.

@en

Phase-resolved volumetric velocity measurements of a pulsed jet are conducted by means of three-dimensional particle tracking velocimetry (PTV). The resulting scattered and relatively sparse data are densely reconstructed by adopting physics-informed neural networks (PINNs), here regularized by the Navier-Stokes equations. It is shown that the assimilation yields a higher spatial resolution, and the process remains robust, even at low particle densities ( 𝑝𝑝𝑝 < 0.001). This is achieved by enforcing compliance with the governing equations, thus leveraging the spatiotemporal evolution of the measured flow field. The results indicate that the PINN reconstructs unambiguously velocity, vorticity and pressure fields with a level of detail not attainable with conventional methods (binning) or more advanced data assimilation techniques (vortex-in-cell). The results of this article support the findings of Clark di Leoni (2023) suggesting that the PINN methodology is inherently suited to the assimilation of PTV data, in particular under conditions of severe sparsity or during experiments with limited control of seeding concentration.@en

Phase-resolved volumetric velocity measurements of a pulsed jet are conducted by means of three-dimensional particle tracking velocimetry (PTV). The resulting scattered and relatively sparse data are densely reconstructed by adopting physics-informed neural networks (PINNs), here regularized by the Navier-Stokes equations. It is shown that the assimilation remains robust even at low particle densities ( ppp < 10 − 3 ) where the mean particle distance is larger than 10% of the outlet diameter. This is achieved by enforcing compliance with the governing equations, thereby leveraging the spatiotemporal evolution of the measured flow field. Thus, the PINN reconstructs unambiguously velocity, vorticity, and pressure fields, enabling a robust identification of vortex structures with a level of detail not attainable with conventional methods (binning) or more advanced data assimilation techniques (vortex-in-cell). The results of this article suggest that the PINN methodology is inherently suited to the assimilation of PTV data, in particular under conditions of severe data sparsity encountered in experiments with limited control of the seeding concentration and/or distribution.

@en

Laser light reflection mitigation in Particle Image Velocimetry (PIV) is crucial for accurate flow field measurements. While numerous methods exist for planar PIV, fewer have been developed for volumetric PIV systems, and in particular for coaxial setups like robotic volumetric PIV. Light reflections in volumetric PIV experiments result in high-intensity regions that corrupt particle detection and analysis. This study presents a novel approach for treating light reflections in robotic volumetric PIV experiments. The proposed method uses image filtering and masking techniques in the wavenumber space to separate particle images from reflection regions. The process involves decomposing the image signal into low- and high-wavenumber components using the 2D discrete Fourier transform (DFT) to then use a high-pass filter to attenuate the intensity of the reflection regions. Finally, a step of automated adaptive masking is applied to remove residual reflection areas that the filtering is not able to eliminate. The proposed approach is tested on experimental data obtained from experiments performed using robotic volumetric PIV on two different geometries: a side-view mirror and a rotating two-blade propeller. Comparison between raw and pre-processed images, as well as particle tracking results, is presented. The results from this data comparison show successful removal of reflection-induced artifacts in instantaneous images by using the spatial Fourier filter automated masking approach. The developed image pre-processing strategy effectively removes unsteady light reflection regions in robotic volumetric PIV images, preventing the appearance of spurious particle tracks and improving the accuracy of flow field measurements. The spatial gaps introduced by the masking procedure can be easily filled in via measurements from multiple directions, which are promptly achieved via the robotic volumetric PIV approach.@en

Image based 3D particle tracking is currently the most widely used technique for volumetric velocity measurements. Inspecting the flow-field around an object is however, hampered by the latter, obstructing the view across it. In this study, the problem of measurement limitations due to the above is addressed. The present work builds upon the recent proposal from Wieneke and Rockstroh (2024), whereby the information of the occluded lines of sight can be incorporated into the particle tracking algorithm. The approach, however, necessitates of methods that accurately evaluate the shape and position of the object within the measurement domain. Methods of object marking and the following 3D registration of a digital object model (CAD) are discussed. For the latter, the Iterative Closest Point (ICP) registration algorithm is adopted. The accuracy of object registration is evaluated by means of experiments, where marking approaches that include physical and optically projected markers are discussed and compared. Three objects with growing level of geometrical complexity are considered: a cube, a truncated wing and a scaled model of a sport cyclist. The registered CAD representations of the physical objects are included in aerodynamic experiments, and the flow field is measured by means of large-scale particle tracking using helium filled soap bubbles. Three operating regimes are studied and compared: monolithic, partitioned and object-aware (OA) monolithic. The results indicate that object registration enables a correct reconstruction of particle tracers and strongly reduces the domain clipping typical of the monolithic approach. Furthermore, the dynamical use of all views in the OA monolithic method offers clear benefits compared to the partitioned approach, namely a lower occurrence of ghost particles. Finally, the combined visualization of the object and the surrounding flow pattern offers means of insightful data inspection and interpretation, along with posing a basis for PIV data assimilation at the fluid-solid interface.@en

In the past years, volumetric velocimetry measurements with helium-filled soap bubbles as tracer particles have been introduced in wind tunnel experiments and performed at large-scale, enabling the study of complex body aerodynamics. A limiting factor is identified in the field of wind engineering, where the flow around ships is frequently investigated. Considering multiple wind directions, the optical access for illumination and 3D imaging rapidly erodes the measurement regions due to shadows and incomplete triangulation. This work formalizes the concepts of volumetric losses and camera redundancy, and examines the performance of multi-directional illumination and imaging for monolithic and partitioned modes. The work is corroborated by experiments around a representative ship model. The study shows that a redundant system of cameras yields the largest measurement volume when partitioned into subsystems. The 3D measurements employing two illumination directions and seven cameras, yield the time-averaged velocity field around the ship. Regions of flow separation and recirculation are revealed, as well as sets of counter-rotating vortices in several stations from the ship bow to the flight–deck. The unsteady regime at the flight–deck is examined by proper orthogonal decomposition, indicating that the technique is suited for the analysis of large-scale unsteady flow features.@en

Recording multiple exposures of the tracer particles onto a single digital image has the potential to simplify the hardware needed for 3D PTV measurements. A sequence with equal time intervals leads to the well-known directional ambiguity problem. Instead, a sequence with irregular time-intervals (two or more) allows resolving the ambiguity. Two fundamental criteria are introduced that determine whether a set of particle samples corresponds to a physical trace for a given neighborhood: the kinematic similarity criterion imposes similarity (i.e. proportionality) between the length travelled by the particle and time elapsed. Additionally, the trace regularity criterion favors sets with minimum fluctuations of the velocity vector. A numerical algorithm, based on combinatorial analysis is presented, whereby all possible sets are scrutinized and the set of particles yielding the minimum disparity from the above criteria corresponds to the physical trace. The algorithm is demonstrated using 3D experimental data and results are benchmarked against the state-of-the-art time-resolved analysis Shakethe-Box (single-frame, single-exposure).@en

The scalability of experiments using PIV relies upon several parameters, namely illumination power, camera sensor and primarily the tracers light scattering capability. Given their larger cross section, helium-filled soap bubbles (HFSB) allow measurements in air flows over a significantly large domain compared to traditional oil or fog droplets. Controlling their diameter translates into scalability of the experiment. This work presents a technique to extend the control of HFSB diameter by geometrical variations of the generator. The latter expands the more limited range allowed by varying the relative helium-air mass flow rates. A theoretical model predicts the bubble size and production rate, which is verified experimentally by high-speed shadow visualization. The overall range of HFSB produced in a stable (bubbling) regime varies from 0.16 to 2.7 mm. Imaging by light scattering of such tracers is also investigated, in view of controversies in the literature on whether diffraction or geometrical imaging dominate the imaging regime. The light scattered by scaled HFSB tracers is imaged with a high-speed camera orthogonal to the illumination. Both the total energy collected on the sensor for a single tracer, as well as its peak intensity, are found to preserve scaling with the square of the diameter at object magnification of 10–1 or below, typical of PIV experiments. For large-scale volumetric applications, it is shown that varying the bubble diameter allows increasing both the measurement domain as well as the working distance of the imagers at 10 m and beyond. A scaling rule is proposed for the latter.@en

A method is proposed to obtain full-domain spatial modes based on Proper Orthogonal Decomposition (POD) of Particle Image Velocimetry (PIV) measurements performed at different (overlapping) spatial locations. When performing robotic volumetric Particle Image Velocimetry (PIV) (Jux et al., 2018), the large-scale mean velocity fields are estimated merging several measurements performed at different (adjacent) locations covered by the robot sequence. The proposed methodology leverages the definition of POD modes as eigenvectors of the spatial correlation matrix to obtain also large-scale modes. Performing measurements over overlapping (50-75%) regions allows to approximate the correlation matrix in the two adjacent domains. When applied over a sequence of views, this method has the potential to deliver full-domain POD modes spanning the volume covered by the robot sequence, even if different regions are covered asynchronously. This methodology is particularly well-suited for applications that seek to investigate large-scale flow structures, whenever the dynamic spatial range (DSR) of the measurement system does not allow to capture the whole domain at once. The methodology is validated using a 2D experimental dataset of a turbulent boundary layer, where patches are artificially created from splitting the PIV measurements, later used as ground truth to assess the results. Furthermore, we apply the technique to a 3D robotic volumetric PIV experiment of the flow around a wall-mounted cube.@en

A method to reconstruct the dense velocity field from relatively sparse particle tracks is introduced. The approach leverages the properties of proper orthogonal decomposition (POD), and it iteratively reconstructs the detailed spatial modes from a first, coarse estimation thereof. The initially coarse Cartesian representation of the velocity field is obtained by local data averaging, where POD is applied. The spatial resolution of the POD modes is enhanced by reprojecting them onto the sparse particle velocity to iteratively improve the reconstruction of the temporal coefficients. Finally, the enhanced velocity field is represented at high-resolution with a reduced order model using the dominant POD modes. The method is referred to as iterative modal reconstruction (IMR), as an extension of the recently proposed data-enhanced particle tracking velocimetry algorithm, introduced for cross correlation-based velocity data. Experiments in the wake of a cylinder at R e D = 27 000 are used to assess the suitability of the method to resolve the turbulent Kármán-Benard wake. The approach is benchmarked against traditional as well as state-of-the-art reconstruction methods, illustrating the capability of IMR of enhancing the spatial resolution of sparse velocity data.

@en

The unsteady flow behaviour of two side-by-side rotors in ground proximity is experimentally investigated. The rotors induce a velocity distribution interacting with the ground causing the radial expansion of the rotor wakes. In between the rotors, an interaction of the two wakes takes place, resulting in an upward flow similar to a fountain. Two types of flow topologies are examined and correspond to two different stand-off heights between the rotors and the ground: the first one where the height of the fountain remains below the rotor disks, and a second one where it emerges above, being re-ingested. The fountain unsteadiness is shown to increase when re-ingestion takes place, determining a location switch from one rotor disk to the other, multiple times during acquisition. Consequently, variable inflow conditions are imposed on each of the two rotors. The fountain dynamics is observed at a frequency that is about two orders of magnitude lower than the blade passing frequency. The dominant characteristic time scale is linked to the flow recirculation path, relating this to system parameters of thrust and ground stand-off height. The flow field is analysed using proper orthogonal decomposition, in which coupled modes are identified. Results from the modal analysis are used to formulate a simple dynamic flow model of the re-ingestion switching cycle.

@en

This work discusses the physics of noise reduction achieved from serrated trailing–edges and its impact by the serration design. An experimental campaign is carried out with a benchmark 2D model based on a NACA 63₃–018 airfoil. Different trailing-edge serrations are tested under several flow speeds and angles of attack conditions to build a complete dataset of acoustic measurements. Systematic modifications of a reference sawtooth serration design are made to its scale and geometry. Scale modifications are based on sawtooth serrations and comprehend carefully considered variations of the serration height (2h), wavenumber (λ), and aspect ratio (2h/λ). Geometric shape modifications are represented by concave–shaped and combed–sawtooth serrations. This study represents a unique sensitivity–based parametric analysis on the scaling and geometric properties of trailing–edge serrations where the impacts of each modification are studied separately. The results obtained are used to provide guidelines for serration design choices and their impact on broadband noise reduction.

@en

The aerodynamic characteristics of a modern road cycling wheel in cross wind are studied through force- and planar PIV measurements in the TU Delft Open Jet Facility. The performance of the 62 mm deep rim is evaluated for three tire profiles, and yaw angles up to 24°. All measurements are executed at 12.5 m/s (45 km/h) freestream- and wheel-rotational velocity. The wheel's rim-tire section in crosswind is found to behave similar to an airfoil at incidence, ultimately resulting in a reduction of the wheel's aerodynamic resistance with increasing yaw angle magnitude. This phenomenon, also referred to as the sail-effect, is limited by the stall angle of the tire-rim profile. The stall angle is found to depend critically on the tire's surface structure. Larger stall angles, resulting in lower resistance, are obtained if the tire profile triggers laminar-to-turbulent boundary layer transition.

@en

Equation 3 for the induced velocity factor a in the section III.B should be: (Formula presented) Instead of: (Formula presented) The first sentence of Chapter V should read that an angle of attack of 8° positions the propeller in a strong adverse pressure gradient, not a strong advance ratio.

@en

Volumetric particle tracking velocimetry measurements are performed in a low-speed wind tunnel to study the flow around a 1:12-scale aircraft model with jet engines operating with thrust reversers. The engine jet and freestream flow velocity are varied to yield a jet to freestream velocity ratio of V_jet/V_∞ ranging from 1.5 to 6. Measurements at such scale (0.5 m³) require the use of strongly scattering helium-filled soap bubbles as flow tracers, which are introduced in both the jet and the freestream flow. The tracer’s three-dimensional motion is determined using an array of cameras and a Lagrangian particle tracking algorithm. The mean velocity field reveals the jet inner structure as well as its interaction with the freestream, the ground board, the nacelle, the fuselage, and the horizontal and vertical tails. The experiments allow detection of exhaust reingestion as well as the aerodynamic interference with control surfaces at the tail segments in a single measurement volume. The results are in good agreement with conventional temperature rake measurements while adding details of the flow topology and of the large-scale unsteady flow fluctuations. Finally, the jet reversal characteristics with varying freestreams and nozzle pressure ratios are assessed, demonstrating the feasibility and versatility of volumetric velocimetry measurements for industrial aerodynamics.

@en

A semi-emperical model is developed, able to capture the aeropropulsive performance characteristics of Over-The-Wing propellers at incidence. The model is based on an hypothesis on the interactions of the propeller- and wing-induced flow fields. Effects of these interactions on the both the thrust and lift are written in a form in which the dominant design parameters appear explicitly. Both the flow hypothesis and model results are validated using experimental data of a single Over-The-Wing propeller. It is shown that for moderate angles of attack, the propulsive thrust is reduced by the wing’s circulation. For angles of attack greater than the stall angle of the isolated wing, thrust is increased by the ingestion of low momentum flow. The propeller is not able to delay stall but induces flow over the wing, which is returned as reduced pressure over the suction side. The model predictions closely match the experimental results for thrust, but integral loading measurements of the wing are required to validate the lift predictions.@en

A physical description of the flow mechanisms that govern the distribution of the wall-pressure fluctuations over the surface of a serrated trailing edge is proposed. Three main mechanisms that define the variation of turbulent pressure fluctuations across the serrated edge are discussed and semi-empirical models are formulated accordingly. It is shown that the intensity of the wall-pressure fluctuations increases at the tips under the effect of an increased convective velocity as a result of sidewise momentum diffusion. Furthermore, the change of impedance across the edge causes a local reduction of the pressure fluctuations in the vicinity of the trailing edge. Finally, aerodynamic loading over the serrations due to the non-symmetric flow created at different angles of attack establishes secondary flow patterns that induce higher wall-pressure fluctuations over the serration edges. The latter effect is present only for serrations under high aerodynamic loading, while the former ones are observed under any conditions. Semi-empirical models are formulated for predicting the variation of the wall-pressure fluctuations over the serration surface based on the three physical mechanisms described. These models are calibrated and compared against experiments conducted on a symmetric airfoil model at high Reynolds numbers.

@en

The impact of aerodynamic loading on a serrated trailing edge is studied experimentally. Aerodynamic and acoustic measurements are conducted on a sawtooth-shaped trailing edge, retrofitted to a flat plate featuring a trailing-edge flap, and placed at incidence to the free-stream flow. The turbulent flow across the trailing edge is inspected by time-resolved three-dimensional velocity field measurements obtained from 4D-PIV, while the wall-pressure fluctuations are measured with surface-embedded microphones. Results discuss the relation between the velocity fluctuations over the serrations, the surface pressure fluctuations, and the far-field noise spectra. The aerodynamic analysis discusses the effect of counter-rotating vortex pairs, generated by the pressure imbalance across the edges of the serrations under loading. It is shown that the interaction of these vortices with the incoming turbulence affects the intensity of the wall-pressure spectrum at the outer rim of the serration surface. On the suction side, the intensity of the pressure fluctuations from the incoming boundary layer dominates over that induced by the vortex pairs. On the pressure side, instead, the velocity gradient prescribed by the vortex pairs produces a significant increase of the pressure fluctuations around the edges. The resulting spatial distribution of the wall-pressure fluctuations directly affects the far-field noise. Scattering predictions carried out with the wall-pressure fluctuations in the centre and root (on the suction side) exhibit good agreement with the measured noise in the low-frequency range, whereas using the surface pressure data at the tip of the serration (on the pressure side) yields a better prediction in the high-frequency range.

@en