We present an experimental realisation of spatial spanwise forcing in a turbulent boundary layer flow, aimed at reducing the frictional drag. The forcing is achieved by a series of spanwise running belts, running in alternating spanwise direction, thereby generating a steady spatial square-wave forcing. Stereoscopic particle image velocimetry in the streamwise–wall-normal plane is used to investigate the impact of actuation on the flow in terms of turbulence statistics, drag performance characteristics, and spanwise velocity profiles, for a non-dimensional wavelength of λ_x⁺=397. In line with reported numerical studies, we confirm that a significant flow control effect can be realised with this type of forcing. The scalar fields of the higher-order turbulence statistics show a strong attenuation of stresses and production of turbulence kinetic energy over the first belt already, followed by a more gradual decrease to a steady-state energy response over the second belt. The streamwise velocity in the near-wall region is reduced, indicative of a drag-reduced flow state. The profiles of the higher-order turbulence statistics are attenuated up to a wall-normal height of y⁺≈100, with a maximum streamwise stress reduction of 45% and a reduction of integral turbulence kinetic energy production of 39%, for a non-dimensional actuation amplitude of A⁺=12.7. An extension of the classical laminar Stokes layer theory is introduced, based on the linear superposition of Fourier modes, to describe the non-sinusoidal boundary condition that corresponds to the current case. The experimentally obtained spanwise velocity profiles show good agreement with this extended theoretical model. The drag reduction was estimated from a linear fit in the viscous sublayer in the range 2≤y⁺≤5. The results are found to be in good qualitative agreement with the numerical implementations of Viotti et al. (Phys Fluids 21, 2009), matching the drag reduction trend with A⁺, and reaching a maximum of 20%. Graphical abstract: (Figure presented.)

Chevron-shaped protrusions have been proposed in the literature for turbulent skin friction reduction. However, there is no consensus on the performance of this passive flow control technique; both an increase and a decrease in drag have been observed in previous studies. There is also no experimental evidence to support the working mechanism behind the drag reduction effect that has been postulated in the literature. In this study, direct force measurements were used to replicate experiments from the literature and, in addition, were used to test new array configurations to characterise the effect of individual design parameters on drag performance. A total of 23 different protrusion configurations were investigated in a turbulent boundary layer flow. In addition to the integral force measurements, particle image velocimetry was used to measure wall-parallel velocity fields in order to extract the statistical sizing and energy of the near-wall cycle turbulence. All configurations increased the drag between 2% and 10% for a friction Reynolds number of 1700. The drag reduction reported in the literature could not be replicated; however, these findings agreed with an experimental and numerical study that reported drag increase. The trend observed in the low-speed streak spacing from the PIV experiments was consistent with that observed in the balance data. Nevertheless, no evidence was found to support the working mechanism proposed in the literature. These results cast doubt on the proposed drag reduction potential of chevron-shaped protrusions. In the authors’ view, the results of this study strengthen previous conclusions regarding their minor increase in drag. Future studies to further approach a consensus are proposed.

Although several previous studies have reported a potential drag-reducing effect of dimpled surfaces in turbulent boundary layers, there is a lack of replicability across experiments performed by different research groups. To contribute to the dialogue, we scrutinize one of the most studied dimple geometries reported in the literature, which has a dimple diameter of 20 mm and a depth of 0.5 mm. There is no general consensus in literature on the drag-reduction performance of this particular dimple geometry, with some studies suggesting a drag reduction, while others report a drag increase. The present combined experimental and numerical study comprises two sets of wind tunnel experiments and a well-resolved large-eddy simulation. The wind tunnel experiments and the large-eddy simulation both depict a total drag increase of around 1%–2% compared to the flat reference case. This finding agrees with a recent study by Spalart et al. (2019). Furthermore, the present wind tunnel experiments have shed light on a plausible reason behind the discrepancy between the study by Spalart et al. (2019) and earlier results from van Nesselrooij et al. (2016). Lastly, the large-eddy simulation results reveal that the pressure drag is the main contributor to the increase in the total drag of the dimpled surface. We believe that these results will contribute to a new consensus on the drag performance of this dimple geometry.

Accurately measuring small changes in aerodynamic drag over a flat surface stands at the core of the development of technologies capable of reducing turbulent friction drag. A wind tunnel drag measurement system was developed which improves significantly on the state of the art. Experimental tests demonstrated that an uncertainty of less than 0.5% of C D at a 95% confidence level was typically achieved, already at drag values below 1 N. This was replicated in two different wind tunnels. A match with literature on riblet performance within 1% of C D was obtained. A crucial aspect of the design is the implementation of a correction for the pressure forces on the streamwise-facing surfaces of the test plate assembly. The flexible architecture of the system in the present realisation makes it suitable for most wind tunnels having a test section width of 400 mm or larger, which allows for accelerated development of turbulent drag reduction concepts from moderate-size low-cost facilities towards flow conditions relevant to the intended industrial application.

An anti-fairing is a concave deformation of the wall around a wing-body junction that can decrease the aerodynamic drag through the activation of a propulsive force generated by the interaction of the curved concave shape and the high-pressure region in proximity of the wing leading-edge. Although this mechanism is well understood, the dynamics of the interaction between the anti-fairing and the junction flow remain largely unexplored. This work brings together all the numerical and experimental studies of the anti-fairing to investigate its effect on turbulent quantities and the robustness of its design to changes to the incoming flow parameters, and to estimate the drag change with respect to a normal wing/flat-plate configuration. It is found that the interaction of the streamwise pressure gradient generated by the anti-fairing with the incoming boundary layer substantially reduces the shear responsible for viscous drag. Furthermore, no significant influence of the incoming boundary layer thickness on the anti-fairing performance is observed. However, a direct drag measurement with a force balance casts some doubts on the possibility to achieve large drag reductions.