This study introduces a novel strategy for fabricating flexible nitrogen dioxide (NO₂) gas sensors based on Indium Oxide (In₂O₃) nanoparticles (NPs) employing selective reduction laser sintering (SRLS) technology. The SRSL technology utilizes ultraviolet (UV) laser selective reduction sintering to precisely and rapidly create oxygen vacancy (OV) defects in In₂O₃ NPs. These oxygen vacancies (OVs) enhance the active adsorption sites and contribute additional free electrons, significantly improving sensor performance at room temperature. The sensors demonstrate excellent response (S = 460.9 at 10 ppm), rapid response/recovery times (τ_resp/τ_reco = 27/570 s), and superior selectivity (response ratio > 400), in addition to robust resistance to light and humidity (under ppm-level NO₂ gas). The sensors also exhibit a low detection limit (200 ppb), a high signal-to-noise ratio (94.8 dB), and good long-term stability (25 days). Moreover, under photo-assisted conditions, the recovery speed of the sensors is further improved. This technology not only provides an innovative strategy for the development of high-performance flexible NO₂ gas sensors but also broadens the application potential of laser direct writing (LDW) technology in advanced materials and sensor fabrications.

This study introduces an innovative approach for fabricating flexible nitrogen dioxide (NO₂) gas sensors based on In2O3 nanoparticles (NPs) using selective reduction laser sintering (SRLS) technology. The SRLS technology enables specific chemical reduction reactions during the sintering process, achieving fabrication and control of oxygen vacancy defects and the porous structure in the In₂O₃ sintering region. The sensor exhibits exceptionally high sensitivity, fast response/recovery times, and superior selectivity for NO₂ gas detection, particularly at room temperature. Compared with traditional NO₂ gas sensor fabrication methods, this technology not only provides a potential way to fabricate highperformance NO₂ gas sensors but also further expands the application potential of laser direct writing (LDW) technology in the fields of advanced materials and sensor fabrication.

Flexible strain sensors play a crucial role in health monitoring, smart wearable devices, and human–machine interaction. Three-dimensional surface evaluation methods for strain sensors offer advantages by being closer to actual strain, featuring a larger working range, and being more suitable for multidirectional strain. In this study, a three-dimensional (3D) surface strain sensor based on polydimethylsiloxane/laser-induced graphene (PDMS/LIG) composite films has been developed. The electromechanical properties of this sensor, encompassing 3D strain range and sensitivity, can be adjusted by manipulating laser parameters and LIG patterns. The key to attaining these specific characteristics lies in the intentional design of crack types and orientations on the sensor's surface. Remarkably, the line-vertical (LV) sensor exhibits outstanding sensitivity with a GF of 211.3. The line-parallel (LP) sensor achieves a GF of 115.1. Additionally, it demonstrates a stretching range of 25% and maintains stable performance over an extensive number of strain/release test cycles (more than 3000 cycles). With these advantages, the 3D strain sensor can not only be applied in human activity monitoring but also monitoring pressure within microchannels in microfluidic chips, suggesting promising applications in the health and medical fields.

In this study, a convenient chitosan oligosaccharide laser lithograph (COSLL) technology was developed to fabricate laser-induced graphene (LIG) electrodes and flexible on-chip microsupercapacitors (MSCs). With a simple one-step CO₂ laser, the pyrolysis of a chitosan oligosaccharide (COS) and in situ welding of the generated LIGs to engineering plastic substrates are achieved simultaneously. The resulting LIG products display a hierarchical porous architecture, excellent electrical conductivity (6.3 Ω sq^-1), and superhydrophilic properties, making them ideal electrode materials for MSCs. The pyrolysis-welding coupled mechanism is deeply discussed through cross-sectional analyses and finite element simulations. The MSCs prepared by COSLL exhibit considerable areal capacitance of over 4 mF cm^-2, which is comparable to that of the polyimide-LIG-based counterpart. COSLL is also compatible with complementary metal-oxide-semiconductor (CMOS) and micro-electro-mechanical system (MEMS) processes, enabling the fabrication of LIG/Au MSCs with comparable areal capacitance and lower internal resistance. Furthermore, the as-prepared MSCs demonstrate excellent mechanical robustness, long-cycle capability, and ease of series-parallel integration, benefiting their practical application in various scenarios. With the use of eco-friendly biomass carbon source and convenient process flowchart, the COSLL emerges as an attractive method for the fabrication of flexible LIG on-chip MSCs and various other advanced LIG devices.

This research introduces a novel and convenient technology, chitosan oligosaccharide laser lithography (COSLL), enabling the creation of flexible laser-induced graphene (LIG) on-chip microsupercapacitors (MSCs) using environmentally friendly chitosan-class polymers for the first time. MSCs prepared through COSLL exhibit a significant areal capacitance exceeding 4 mF cm^-2, comparable to that of the polyimide-LIG-based counterparts. COSLL seamlessly integrates with the micro-nano thin-film process, allowing the capacitance of resulting LIG/Au MSCs to be further increased to about 8 mF cm^-2. Leveraging an eco-friendly biomass carbon source and featuring a convenient process flowchart, COSLL emerges as an appealing method for fabricating flexible LIG on-chip MSCs.

The fabrication of flexible pressure sensors with low cost, high scalability, and easy fabrication is an essential driving force in developing flexible electronics, especially for high-performance sensors that require precise surface microstructures. However, optimizing complex fabrication processes and expensive microfabrication methods remains a significant challenge. In this study, we introduce a laser pyrolysis direct writing technology that enables rapid and efficient fabrication of high-performance flexible pressure sensors with a micro-truncated pyramid array. The pressure sensor demonstrates exceptional sensitivities, with the values of 3132.0, 322.5, and 27.8 kPa^-1 in the pressure ranges of 0-0.5, 0.5-3.5, and 3.5-10 kPa, respectively. Furthermore, the sensor exhibits rapid response times (loading: 22 ms, unloading: 18 ms) and exceptional reliability, enduring over 3000 pressure loading and unloading cycles. Moreover, the pressure sensor can be easily integrated into a sensor array for spatial pressure distribution detection. The laser pyrolysis direct writing technology introduced in this study presents a highly efficient and promising approach to designing and fabricating high-performance flexible pressure sensors utilizing micro-structured polymer substrates.

Laser-induced graphene (LIG) has aroused a wide range of research interests ranging from micro-nano energy devices to the Internet of Things (IoT). Nevertheless, the non-degradability of most-used synthetic polymer carbon sources poses a serious threat to the environment. In this work, ecofriendly chitosan-based derivatives, including carboxymethyl chitosan (CMCS), chitosan oligosaccharide, and chitosan hydrochloride, are successfully converted into LIGs for the first time via a convenient one-step CO₂ laser engraving at ambient air. The obtained LIGs are characterized by a three-dimensional hierarchical porous structure and exhibit good sheet conductivity. The consecutive carbonization and graphitization mechanism of target precursors induced by laser heat accumulation is also deeply discussed. Besides, based on a mechanically reliable LIG/CMCS composite film and tribo-negative acrylic/polyimide anti-layers, two contact-separation mode triboelectric nanogenerators are built and their power densities range from 1.44 to 2.48 mW cm^-2. These devices with long cycle life can be used for low-frequency mechanical energy harvesting and commercial capacitance charging, which could be potentially applied in the wireless sensor network nodes. Such a family of chitosan derivatives paves a new route for LIG synthesis and provides new ideas for ecofriendly LIG electronics.

In recent years, metal crack-based stretchable flexible strain sensors have attracted significant attention in wearable device applications due to their extremely high sensitivity. However, the tradeoff between sensitivity and detection range has been an intractable dilemma, severely limiting their practical applications. Herein, we propose a laser transmission pyrolysis (LTP) technology for fabricating high-performance flexible strain sensors based on (Au) metal cracks with the microchannel array on the polydimethylsiloxane (PDMS) surface. The fabricated flexible strain sensors exhibit high sensitivity [gauge factor (GF) of 2448], wide detection range (59% for tensile strain), precise strain resolution (0.1%), fast response and recovery times (69 and 141 ms), and robust durability (over 3000 cycles). In addition, experiment and simulation results reveal that introducing a microchannel array enables the stress redistribution strategy on the sensor surface, which significantly improves the sensing sensitivity compared to conventional flat surface sensors. Based on the excellent performance, the sensors are applied to detect subtle physiological signals, such as pulse and swallowing, as well as to monitor large-scale motion signals, such as knee flexion and finger bending, demonstrating their potential applications in health monitoring, human-machine interactions, and electronic skin.