This paper presents a Switching-Mode Regulating Rectifier (SM-RR) with single-stage dual-output regulation for biomedical wireless power transfer applications. To achieve both a high power conversion efficiency (PCE) and a long power transfer distance, the proposed SM-RR can seamlessly switch its operation between voltage mode and resonant current mode. To meet multi-power-rail requirements in loading circuits, it employs only three power transistors to provide two regulated outputs with parallel pulse-frequency modulation, which achieves unobservable cross-regulations. The prototype chip, fabricated in a 180 nm CMOS process, achieves two regulated outputs at 1.8 V and 3.3 V, respectively, up-to- 92.33% PCE, and up-to-42% transfer range extension compared to conventional voltage-mode receivers.

@en

A single-stage dual-output regulating voltage doubler (DOVD) is proposed for biomedical wireless power transfer (WPT) systems. Derived from the full-wave voltage doubler (VD) topology, it achieves ac-to-dc rectification and dual-output voltage regulation in a single stage by using only two power transistors. The DOVD's inherent voltage conversion ratio (VCR) of 2 enhances the overall voltage gain of a WPT system, thus extending the transfer range against varying link conditions. To eliminate cross-regulation between the two outputs and provide fast load-transient responses, a parallel pulse-frequency modulation (PPFM) controller is proposed. In addition, a digital-tuning adaptive delay compensation technique with fast error-variation responses is proposed to achieve soft-switching in the power stage. Implemented in a 180-nm Bipolar-CMOS-DMOS (BCD) technology and operating at 6.78 MHz, the proposed DOVD achieves dual regulated outputs at 1.8 and 3.3 V, a VCR of up to 1.875, and a power conversion efficiency (PCE) of up to 92.95% over an output power range of 2.6-90.5 mW. It also achieves instant load-transient responses and unnoticeable cross-regulation during 25× load transients at both outputs.

@en

This work presents a switched capacitor power converter (SCPC) with instant transient response and minimized steady-state output ripple. The proposed SCPC employs a hybrid control strategy that amalgamates the strengths of hysteresis and continuous frequency modulation (CFM) controls, thus elevating transient performance while maintaining a small steady-state ripple. The system adopts a 10 -phase interleaved recursive switched capacitor (RSC) topology with adaptive capacitor sizing to achieve configurable voltage-conversion ratios (VCR) with heightened efficiency, power density, and load ability. Additionally, a novel adaptive switch-sizing technique is introduced to improve light-load efficiency. Fabricated in 180-nm BCD technology, the chip supports a wide-range load current of 0.7mA-120mA and converts a 0.8 -to-3.6V input to a 0.25 -to2.4 V output with a peak efficiency of 87.1%. The proposed converter simultaneously achieves a low voltage ripple of 12 mV and an over-/under-shoot voltage of less than 50 mV even under significant load transient steps (171X).

@en

This article presents a 13.56-MHz wireless power transfer (WPT) system with coupling variation robustness and high efficiency for powering biomedical implantable devices (IMDs). To sustain reliable power transfer against inductive-link fluctuation, a hybrid voltage-/current-mode (V/CM) receiver (RX) is proposed to provide CM recovery when the coupling becomes weak for VM operation. To optimize the end-to-end (E2E) efficiency, a digital pulsewidth modulation (PWM)-based global power regulation technique is proposed, which allows a fully on/off operation of the three-mode power amplifier (PA) at the transmitter (TX) side and fast load-transient responses. Moreover, the system adopts a fully integrated voltage-sensing load-shift-keying (LSK) demodulation technique, which replaces conventional current sensing methods with a streamlined implementation and reduced power consumption. Both prototype TX and RX chips were fabricated in a 180-nm CMOS process. The proposed system, powered by a 1.8-V supply at TX, realizes a regulated 1.8-V dc output at RX. With the help of the hybrid V/CM RX, the proposed system achieves an up-to-150% WPT range extension compared to VM-only operation and an up to 7.2-cm WPT range. Benefiting from the global digital-PWM regulation, it achieves up to 72.3% E2E efficiency over the loading range from 0.18 to 81 mW. A 10- μ s load-transient recovery is also attained at a 164 × load step with a 110-mV undershoot and unnoticeable overshoots.

@en

This article presents a 10mV-startup-voltage thermoelectric energy harvesting system, assisted by a piezoelectric generator (PEG) as a cold starter. It exploits the fact that when a thermoelectric energy harvesting system is implemented in a place where kinetic energy is also present, the PEG starter can provide a clock signal to start the system. Thanks to the high output impedance of the PEG, the generated clock voltage can easily go over several hundreds of mV, which can be used to drive the boost converter to harvest thermoelectric energy even at an extremely low thermoelectric generator (TEG) voltage. The proposed system was fabricated in a 180-nm BCD process. The measurement results show that the TEG system can start up from the cold state with a TEG voltage as low as 10 mV while maintaining a 63.9% efficiency. The peak power conversion efficiency reaches 83.7% when the TEG voltage is 55 mV.@en

In this letter, a 6.78-MHz single-stage regulating voltage-doubling rectifier is presented for biomedical wireless power transfer (WPT) applications. Derived from a full-wave voltage doubler, a theoretical voltage conversion ratio (VCR) of 2 can be achieved, which benefits the end-to-end voltage gain of a biomedical WPT system with varying link conditions. As a result, a wider WPT operational range and less coil-link loss can be achieved. To avoid efficiency loss due to cascading, the rectifier output is in-situ regulated in a sub-50-mV hysteresis window by pulse-skipping control. To ensure a high power conversion efficiency (PCE), adaptive delay-compensated active diodes are adopted with an offset locking technique. The input/output capacitors of the rectifier are fabricated on-chip, achieving a fully integrated design. The rectifier was fabricated in a 180-nm BCD process, occupying a silicon area of 0.3/2.7 mm2 without/with on-chip capacitors. The measurements show that the rectifier can realize a peak PCE at 90.6% when the output power is 79.8 mW. The PCE and VCR are achieved higher than 86.4% and 1.6, respectively, over a large loading range (from 1 to 40 mA). The rectifier can output a maximum power of 159.2 mW, satisfying most biomedical implants.

@en

Dual-output regulating rectifier is highly desired in wireless power transfer (WPT) for sub-100mW bioimplants. Such rectifiers perform voltage rectification and dual-output regulation simultaneously, thus avoiding post DC-DC conversions and cascaded power losses [1 –4]. However, the conventional dual-output structure suffers from a low voltage conversion ratio (VCR) (< 1) due to the full bridge rectifier (FBR) topology (Fig. 1), severely limiting the receiver operation when wireless link condition varies [1–2]. In order to extend the operational range without increasing the power demand from the transmitter, [3] presents a charge-pump based dual-output rectifier; however, it uses 10 power transistors (PTs) and 8 off-chip capacitors, degrading the power conversion efficiency (PCE) and increasing the integration cost. Alternatively, the current-mode dual-output rectifier can realize a VCR higher than 1, but the output power is limited to less than 10mW [4], which is insufficient for advanced bioimplants. In this work, a 13. 56MHz single-stage dual-output voltage doubler (DOVD) is proposed to address the above limitations, which employs only two PTs and a fully integrated design. lt can achieve a peak VCR of1.78 and outputs power up to 8lmWwith a 91.8% peak PCE.@en

In this article, we propose a reconfigurable regulating rectifier with a wide operational range for wireless power transfer. The proposed three-mode rectifier achieves a broad range voltage regulation without global loop control to minimize the chip area occupation. Compared with previous work, more working modes and greater voltage gain allow the proposed rectifier to regulate lower input power, which extends the voltage regulation range. A local loop control scheme is proposed for voltage rectification with three modes. It adaptively senses the duty cycle of the mode signal to determine the working mode of the rectifier, and configure the rectifier to the desired mode for voltage regulation. The proposed system was designed and fabricated in a 180-nm BCD technology with an active area of 1.17 mm2. The measurement results show that the proposed system can rectify wide-range input ac power to a regulated output. The achieved voltage conversion ratiois between 0.95X and 2.68X, with a peak power conversion efficiencyat 87.4%.

@en

A 6.78 MHz dual-output reconfigurable rectifier for wireless power transfer is presented. The proposed rectifier integrates AC-DC rectification and DC-DC regulation into a single-stage topology, alleviating received power loss and reducing system volume cost. By adding a switch matrix after rectifying bridge, a dual output can be realized and regulated by a hysteretic control unit. The proposed rectifier can work in six operation modes by reconfiguring, and each output can be regulated in three modes. As a result, fine output regulation and large output-driving capability can be achieved. Designed in a 180-nm BCD process using standard 5-V devices, the dual-output rectifier provides two output voltages at 3 V and 5 V, and delivers a maximum power of 1.6 W. The peak post-layout simulated power conversion efficiency reaches 80.1% when both load currents are 0.2 A.@en