Piezoelectric energy harvesting (PEH) is a promising approach to collecting ambient kinetic energy as the power supply for electronic devices. In many PEH designs, the maximum power point tracking (MPPT) technique is exploited to enhance the output power of the system. However, a typical PEH system requires a separate power stage for MPPT, which requires a large external rectified capacitor for MPPT operation and suffers from cascaded power efficiency loss. This paper presents an MPPT-integrated bias-flip rectifier where the MPPT and AC-DC rectifier are merged into one stage, resulting in fewer off-chip capacitors, faster MPPT, and less cascaded energy loss. The proposed circuit was fabricated in a 0.18μm CMOS process, and the measurement results show a 7.7 × energy extraction enhancement.

@en

The agglomeration of cohesive particles can deteriorate fluidization quality and cause the defluidization of a bed, which is a common issue found in the applications of fluidized beds. This study aims to gain a better understanding of particle cohesion on agglomeration/fluidization behaviors and the effective methods for achieving a better fluidization quality, through numerical simulations based on the coupled approach of computational fluid dynamics and discrete element method (CFD-DEM). The effects of particle cohesion, gas velocities or flow conditions, and the bed geometry on the agglomeration and fluidization behaviors are analyzed. It is shown that the increase of particle cohesion can lead to deteriorated particle mixing, significant agglomeration of particles, and defluidization of the bed; the agglomeration-induced defluidization of highly cohesive particles is difficult to mitigate in a conventional flat-bottom fluidized bed. As large-sized agglomerates are more frequently found in the bottom of the bed, the spouted gas flow is then utilized and demonstrated to be effective in assisting the deagglomeration and fluidization of highly cohesive particles. Through the comparison of various spouted beds and spouted fluidized beds, the effective design of the bed bottom is identified for achieving a higher fluidization quality. Corresponding mechanisms underlying spout-assisted deagglomeration and fluidization are found to be much related to not only the enhanced particle-fluid but also particle-wall interactions in the confined space of a conical bed bottom, thus explaining the effectiveness and the importance of the bottom conical geometry of spouted beds. The obtained findings may help to understand the agglomeration-induced defluidization of fluidized beds and assist the fluidization of highly cohesive particles by the effective design of spouted beds.

@en

This article presents a 10mV-startup-voltage thermoelectric energy harvesting system, assisted by a piezoelectric generator (PEG) as a cold starter. It exploits the fact that when a thermoelectric energy harvesting system is implemented in a place where kinetic energy is also present, the PEG starter can provide a clock signal to start the system. Thanks to the high output impedance of the PEG, the generated clock voltage can easily go over several hundreds of mV, which can be used to drive the boost converter to harvest thermoelectric energy even at an extremely low thermoelectric generator (TEG) voltage. The proposed system was fabricated in a 180-nm BCD process. The measurement results show that the TEG system can start up from the cold state with a TEG voltage as low as 10 mV while maintaining a 63.9% efficiency. The peak power conversion efficiency reaches 83.7% when the TEG voltage is 55 mV.@en

Piezoelectric energy harvesting (PEH) has attracted much attention as an approach to exploit ambient vibrational energy to power self-sustained devices. Among the proposed interface circuits for PEH, Synchronized Switch Harvesting on Capacitor (SSHC) rectifier distinguishes itself since it achieves high power efficiency while requires no inductor. The power SSHC can extract is a function of the voltage flip efficiency. In previous studies the flip efficiency is given only under particular condition, which limits the analysis and design of SSHC circuits. This paper presents the derivation of a generic flip efficiency expression. From the result, a novel capacitor-scaling design is proposed which can reduce the total switched capacitance by up to 50% while achieving the same performance (or to enhance performance while maintaining the total capacitance). This is particularly preferred for a fully integrated design and can validated by simulations implemented in a 0.18 m. CMOS BCD technology.@en

Ultrasonic wireless power transfer (WPT) has been proved to be a promising approach to power biomedical implants. To extract the energy generated from the transducer, a rectifier is typically required. Previous inductor-based rectifiers (SSHI and SECE) require a large off-chip inductor to achieve good performance, which is not desired for miniaturization and safety reasons. Synchronized switch harvesting on capacitors (SSHC) rectifiers have been proved to achieve high performance without inductors; however, they are mainly designed for low-frequency kinetic energy harvesting. In this paper, an improved SSHC rectifier is designed to achieve a fully integrated design with all flying capacitors implemented on-chip. The proposed SSHC rectifier can properly operate at ultrasonic excitation frequency (100 KHz) with precise switching time control and ultrafast voltage flipping techniques. In addition, an on-chip ultralow-power LDO allows the system to be self-sustained. The system is designed in a TSMC 180nm BCD technology and post-layout simulation results are presented.@en

A nanopower highly efficient low-dropout (LDO) regulator for energy harvesting (EH) applications is presented in this paper. The LDO is fully autonomous with a bandgap reference (BGR) featuring a novel bandgap supply-switching (SS) topology, an over-voltage protection (OVP), a under-voltage lockout (UVLO) and control block to obtain stable output and robust cold-start. The system provides configurable voltage supply (1.1 \sim2V) for potential loads, while consuming as low as 66 nW power. The entire system achieves a peak power efficiency of 95.6% at Vout=2V and I-{\iota-{oad}}=100\muA.

@en

Synchronized switch harvesting on inductor (SSHI) is an efficient active rectifier to extract energy generated from piezoelectric transducer in piezoelectric energy harvesting system. Unlike passive rectifiers, SSHI rectifiers require a power supply to drive synchronized switches. Unfortunately, there is no stable supply when the system starts from the cold state. Most designs let the system work as a passive full bridge rectifier (FBR) to charge power capacitor until a supply is available. However, a FBR requires high open-circuit voltage (VOC) and the FBR’s output voltage cannot go over VOC. This prevents the system from starting the SSHI rectifier if VOC is low. This paper proposes a new transducer reconfiguration design to lower the required VOC by 4 $\times$ to start up the SSHI system from the cold state. The proposed system is designed in a 0.18$-\mu$m BCD process and post-layout simulations show that the successful cold-startup under low VOC voltage.@en