Bitumen fatigue resistance is critical to determine the overall fatigue performance and service life of asphalt pavements. However, the mechanisms responsible for fatigue damage of bitumen have previously not been well understood. Molecular dynamics (MD) simulation has recently emerged as a powerful computer-aided numerical technique to model the microscopic failure behaviours in materials. This study aims to use the MD method to investigate the molecular origin of bitumen fatigue damage. The molecular models of the virgin and aged PEN70/100 bitumen were firstly constructed based on their saturate, aromatic, resin and asphaltene (SARA) four fractions. An MD equilibrium was run on the developed bitumen models with the assigned interatomic potentials. Following an MD-based tensile simulation, a strain-controlled fatigue simulation was performed to study the nanostructure and damage behaviours of the virgin and aged bitumen under fatigue loading by calculating the stress-strain response, potential energy, molecular structure and nanovoid volumes. Furthermore, a rheometer measurement was also conducted to characterise the fatigue damage of the bitumen directly by a crack length at the macroscale. Results indicate that the bitumen molecules become unfolded and tend to align along the loading direction when fatigue loading was applied. The change in the molecular configuration helped the molecular chains move closer together and thus contributed to the reduction of the intermolecular interactions including the van der Waals and Coulombic energies. With the increasing load cycles, nanovoids were formed and grew in the bitumen through molecular rearrangement and movement, leading to microscopic fatigue damage of the bitumen. It was found that the aged bitumen produced more severe fatigue damage than the virgin bitumen, which was indicated by the MD-based nanovoid volume at the molecular scale and the DSR-based crack length at the macroscale. The findings from MD simulation provide a fundamental understanding of the molecular origin of fatigue damage, that cannot be experimentally detected for bitumen materials.@en

The Guide for Design of Pavement Structures (AASHTO 86/93) and Mechanistic Empirical Pavement Design Guide (MEPDG) are two common methods to design continuously reinforced concrete pavement (CRCP) published by the American Association of State Highway and Transportation Officials (AASHTO) in the USA. The AASHTO 86/93 is based on empirical equations to assess the performance of highway pavements under moving loads with known magnitude and frequency derived from experiments on AASHTO road tests. The MEPDG is a pavement design method based on engineering mechanics and numerical models for analysis. It functions by incorporating additional attributes such as environment, material properties, and vehicle axle load to predict pavement performance and degradation at the selected reliability level over the intended performance period. In order to evaluate the CRCP design procedure and performance, crack width (CW) and crack spacing (CS) from five examined test tracks in Europe with different climate condition, base layer, geometry, and materials were collected in this paper and compared with predicted distresses as well as CW and CS from AASHTO 86/93 and MEPDG design methods. The results show that the interactions between geometrics, material properties, traffic, and environmental conditions in the MEPDG method are more pronounced than in the AASHTO 86/93 and the prediction of CS and CW based on MEPDG matched closely with the recorded data from sections@en

Ultrasonic wire bonding is one of the critical challenges for power semiconductor manufacturing process, especially for silicon carbide (SiC) power devices. Packaging-related strain on the dies is one of the limiting factors for SiC devices scaling towards mass-production. Furthermore, due to the high current demand for SiC power device packaging, thick bond wires are often needed, which brings major challenges for the ultrasonic wire bonding process. Thus, computational simulation methods are under development to assist the wire bonding process. This paper presents a simulation method that can quickly narrow the process window for thick bond wires on SiC power devices beforehand. A process model was created to adapt process parameters of bonding force and power. This model aims to simulate the bond deformation for a discretized bonding area. Wire deformation and equivalent plastic strain were then examined and compared. The model was further validated through experiments. Experimental validation of the wire bonding model reveals a suitable deformation of bond wires, which helps to improve thick wire bonding reliability for power electronics packaging.@en

Permeable pavements are often affected by pore clogging, which leads to their functional failure and reduced service life. However, the clogging mechanism and its impact on the permeability and complex pore microstructures in pervious pavement remains unclear. The aim of current study is to quantify the clogging behavior in pervious pavement materials and carry out investigations on the development of pore characteristics and permeability. Novel Polyurethane bound pervious mixture (PUPM) were adopted for comparative study in present research with conventional Porous Asphalt (PA). The Aachen Polishing Machine (APM) was selected to perfectly serve as a simulator for clogging process of pavement in the actual service condition. The development of pore characteristics in terms of clogging was experimentally illustrated. The developed experiments and analysis can further strengthen the understanding of the clogging mechanism within the porous pavement material.@en

To improve the energy harvesting efficiency of the piezoelectric device, a stack units-based structure was developed and verified. Factors such as stress distribution, load resistance, loads, and loading times influencing the piezoelectric properties were investigated using theoretical analysis and experimental tests. The results show that the unit number has a negative relationship with the generated energy and the stress distribution has no influence on the power generation of the piezoelectric unit array. However, with a small stress difference, units in a parallel connection can obtain high energy conversion efficiency. Additionally, loaded with the matched impedance of 275.0 kΩ at 10.0 kN and 10.0 Hz, the proposed device reached a maximum output power of 84.3 mW, which is enough to supply the low-power sensors. Moreover, the indoor load test illustrates that the electrical performance of the piezoelectric device was positively correlated with the simulated loads when loaded with matched resistance. Furthermore, the electrical property remained stable after the fatigue test of 100,000 cyclic loads. Subsequently, the field study confirmed that the developed piezoelectric device had novel piezoelectric properties with an open-circuit voltage of 190 V under an actual tire load, and the traffic parameters can be extracted from the voltage waveform@en

Porous asphalt (PA) pavements are widely employed in areas with wet climates. As particle enhancement inclusions in asphalt mastic, mineral fillers play essential roles in improving the performance of PA pavements. This study developed a coupled multiscale finite element (FE) model, involving the mesostructure of PA mixture and PA pavement. Four types of mastic properties were employed with four mineral fillers (Granodiorite, Limestone, Dolomite, and Rhyolite) in the mesoscale portion of the pavement model to analyse the effects of filler types on the performance of pavements. The performances (load-bearing capacity, rutting resistance, and ravelling resistance) of pavements with different fillers were identified and ranked, and their correlations with the chemical components of the four fillers were analysed. The computational results showed that pavements with Rhyolite and Granodiorite fillers have higher load-bearing capacities and rutting resistance, while the Limestone and Dolomite fillers can improve the ravelling resistance of the PA pavements. In the correlation analysis, the chemical components Al₂O₃ and SiO₂ play dominant roles in improving the load-bearing capacities and rutting resistance of the PA pavements, and the fillers with high percentages of CaO can improve the ravelling resistance of the PA pavements.

@en

The pore-water pressure generated by intermittent dynamic vehicle loading under various saturation states is recognized as a critical factor influencing the behaviour of permeable pavement structures, especially the behaviour of UGB layer. However, the underlying mechanisms of hydro-mechanical interaction in the UGB layer and the influence on the pavement structure are still unclear. This study aims to characterize the changes in dynamic response in permeable pavement structures under various saturation conditions by considering the hydro-mechanical interaction within the UGB layer. To achieve this objective, a full-scale test track with a PUPM wearing course was constructed. Pressures and water distribution were characterized by embedded sensors within different layers of the test track when subjected to the accelerating pavement test. Based on the coupled SAME model, the water distribution and the dynamic response of UGB in the rainfall events were both characterised and solved by FEM. The results predicted by the proposed SAME model correspond to the field measurements, and the influence of the water content on the resilient modulus distribution within the UGB layer was then estimated. Based on the predictions for the stress state of the UGB layer, the sensitivity analysis was also proposed.

@en

Sustainable and resilient pavement infrastructure is critical for current economic and environmental challenges. In the past 10 years, the pavement infrastructure strongly supports the rapid development of the global social economy. New theories, new methods, new technologies and new materials related to pavement engineering are emerging. Deterioration of pavement infrastructure is a typical multi-physics problem. Because of actual coupled behaviors of traffic and environmental conditions, predictions of pavement service life become more and more complicated and require a deep knowledge of pavement material analysis. In order to summarize the current and determine the future research of pavement engineering, Journal of Traffic and Transportation Engineering (English Edition) has launched a review paper on the topic of “New innovations in pavement materials and engineering: A review on pavement engineering research 2021”. Based on the joint-effort of 43 scholars from 24 well-known universities in highway engineering, this review paper systematically analyzes the research status and future development direction of 5 major fields of pavement engineering in the world. The content includes asphalt binder performance and modeling, mixture performance and modeling of pavement materials, multi-scale mechanics, green and sustainable pavement, and intelligent pavement. Overall, this review paper is able to provide references and insights for researchers and engineers in the field of pavement engineering.

@en

Permeable pavements have been widely used as an effective means to improve hydrological characteristics and the ecology of the urban environment. This study aims to investigate the response of fully permeable pavement (FPP) subjected to dynamic loading under dry and saturated conditions. A full-scale test track topped with polyurethane bound permeable material (PUPM) was built to obtain the stress response with an accelerated pavement test (APT) system. In addition, comprehensive analyses were performed based on the coupled Stress-dependent Moisture-sensitive Cross-anisotropic Elastoplastic (SMAEP) model in FEM. The APT test showed that the worst state was observed when the pavement structure was fully saturated, and that and brittle failure of the pavement surface occurred when the critical load level was achieved. The prediction of vertical stress predicted by Stress-dependent Cross-anisotropic Elastic (SAE) and SMAEP were both validated with the field data. The horizontal stress predicted by SAE gave a very high and unreasonable tensile stress prediction at the bottom of the unbounded granular base (UGB) layer when subjected to the high load level. With the consideration of moisture effect and the plastic properties of the material, the prediction made by SMAEP is effective to estimate the dynamic response of the UGB layer. Based on the sensitivity analysis, the optimized designs for FPP based on PUPM were suggested.

@en

To reduce the thermal-oxidative aging of asphalt and the release amount of harmful volatiles during the construction of asphalt pavement, a new composite anti-aging agent was developed. Since the volatiles were mainly released from saturates and aromatics during the thermal-oxidative aging of asphalt, expanded graphite (EG) was selected as a stabilizing agent to load magnesium hydroxide (MH) and calcium carbonate (CaCO₃) nanoparticles for preparing the anti-aging agents of saturates and aromatics, respectively. Thermal stability and volatile constituents released from saturates and aromatics before and after the thermal-oxidative aging were characterized using the isothermal Thermogravimetry/Differential Scanning Calorimetry-Fourier Transform Infrared Spectrometer test (TG/DSC-FTIR test). Test results indicate that anti-aging agents of EG/MH and EG/CaCO₃ effectively inhibit the volatilization of light components in asphalt and improve the thermal stability of saturates and aromatics. Then, the proportions of EG, MH, and CaCO₃ added in the developed composite anti-aging agent of EG/MH/CaCO₃ are 2:1:3 by weight. EG/MH/CaCO₃ plays a synergetic effect on inhibiting the thermal-oxidative aging of asphalt, and reduces the release amount of harmful volatiles during the thermal-oxidative aging after EG/MH/CaCO₃ is added into asphalt at the proposed content of 10 wt. %. EG plays a synergistic role with MH and CaCO₃ nanoparticles to prevent the chain reactions, inhibiting the thermal-oxidative aging of asphalt.

@en

For a heavy-haul locomotive within a wheel repairing period, wheel polygonal wear with different operating mileages is obtained by field testing. The test results show that the maximum radial runout of the wheel can increase to 0.87 mm and accompany with the typical damage of wheel tread shelling. Taking the wheel polygons as input excitation, the locomotive-track coupled dynamic model is established, which is verified by the comparisons of test and calculated wheelset vertical acceleration in time and frequency domains. The variable wheel-rail friction coefficient is introduced so as to consider the dry and wet rail conditions. The wheel-rail dynamic contact characteristics under the traction and dry-wet rail surface conditions are analysed simultaneously. It is found that the wheel polygon deteriorates the locomotive traction performance and induces the obvious wheel-rail slipping with large tangential stress, especially in wet rail condition. In dry condition, the wheel-rail could contact generally in the adhesion state. But the longitudinal creep forces fluctuate locally with some larger amplitudes closed to the adhesion force, which is mainly attributed to the excitation of serious wheel polygon. Comparing with the results of the newly repaired wheel, the maximum wheel-rail vertical force, longitudinal force, normal stress and tangential stress at the end of wheel repairing period can increase by 55 kN, 28 kN, 240 MPa and 470 MPa in sequence. The wheel-rail slipping and high-stress state in traction condition should be the dominant factors contributing to the wheel damage of tread shelling.

@en