Self-healing is a biological phenomenon in which living organism responds to the suffered damage in a complex way. Inspired by the self-healing phenomenon in nature, various biomimetic healing methods rooted in intrinsic or extrinsic healing mechanisms have been explored. Research on novel self-healing asphalt materials with intelligent response is at the cutting-edge of materials science and offers a potential strategy for building long-life and low-carbon asphalt concrete infrastructure. This paper describes the progress of research on extrinsic self-healing asphalt materials and makes a clear distinction between intrinsic and extrinsic self-healing. The asphalt self-healing mechanism is interpreted by capillary flow theory, phase field theory, molecular diffusion theory and surface energy theory form various perspective. The extrinsic self-healing strategies including thermal induced healing and rejuvenator induced healing are proposed to enhance the healing level of cracked asphalt materials. A brief review of the methods including fracture-healing test and fatigue-healing test for assessing the efficacy of different extrinsic healing methods is presented. The thermal induced healing method bring high crack repair efficiency for asphalt concrete and the rejuvenator induced healing strategy not only improve the healing ratio of cracked asphalt concrete but also regenerate the ageing asphalt in situ. Important lessons for prospective research on the creation of novel self-healing asphalt materials are highlighted.

As a kind of solid waste, using Prestressed High-Strength Concrete Pile Waste Concrete (PPWC) as the replacement for limestone filler in asphalt concrete can not only reduce the accumulation of PPWC and increase its utilization but also avoid the increased road construction costs and environmental degradation associated with limestone mining. This study aims to investigate the effect of using PPWC filler to replace limestone filler on the road performance of asphalt concrete. Firstly, PPWC was ground into filler particles with a diameter less than 0.075 mm. The particle characteristics such as surface morphology, particle size distribution and chemical composition of PPWC filler and limestone filler were compared. Then, PPWC filler was used to replace limestone filler with different volume fractions to prepare asphalt concrete, and the water damage resistance, high-temperature rutting resistance, low-temperature crack resistance, fatigue resistance and adhesion performance of asphalt concrete were tested. The results showed that PPWC filler has a smaller particle size and rougher surface than limestone filler, and it contains Ca(OH)₂ produced by hydration. The addition of PPWC filler can effectively improve the mechanical properties of asphalt concrete without reducing its water damage resistance. PPWC filler can improve the high-temperature rutting resistance and low-temperature crack resistance of asphalt concrete, but reduce its low-temperature fatigue resistance. The low content of PPWC filler will enhance the adhesion between asphalt mortar and aggregate. However, when the content of PPWC filler exceeds 50%, Ca (OH)₂ in PPWC will reduce the adhesion between acid asphalt mortar and alkaline basalt aggregate. Therefore, the use of PPWC as filler in asphalt mixtures provides a reliable solution for the sustainable development of road materials.

Aimed to address the low utilization rate of steel slag (SS) and its challenge in resource utilization in China, this study developed ternary geopolymers made by high-content (50%) SS together with fly ash (FA) and granulated blast furnace slag (GBFS). The effects of GBFS content (0–40%) and curing methods (water curing, standard curing, sealed curing, and heat curing) on the working performance and microstructure of geopolymers were investigated. Microscopic analysis such as X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG-DTG), and scanning electron microscopy (SEM) were utilized to investigate the hydration process and products of geopolymers under different curing conditions and GBFS content. The results indicated that when the GBFS content increased from 0% to 40%, the fluidity of the mixture decreased by 11.7%, the initial setting time of the geopolymer slurry decreased by 76%, and the geopolymer mortar's 28d compressive strength increased from 31.9 MPa to 60.6 MPa. At room temperature, the geopolymer mortar's 28d compressive strength was higher under standard curing (70.8 MPa) compared to water curing (57.5 MPa) and sealed curing (68 MPa). The geopolymer mortar cured at 60 °C for 24 h exhibited the highest 28d compressive strength (76.3 MPa). However, excessively high curing temperatures or prolonged durations led to more shrinkage cracks and reduced the compressive strength. The microscopic analysis revealed that the main gel products of ternary geopolymer were C-(A)-S-H gel. The amount of gel products is directly related to the strength of geopolymers. The developed ternary geopolymer has the potential to promote the large-scale utilization of SS in the concrete industry, making a significant contribution to sustainable development.

Using solid waste to replace limestone filler in asphalt concrete can not only reduce the cost of road construction, but also improve the utilization rate of solid waste. In this study, PHC pile waste concrete (PPWC) was innovatively used to replace limestone filler in asphalt mixture and its effect on the physical and rheological properties of asphalt mastics was studied. Firstly, PPWC was ground into filler particles with a diameter less than 0.075 mm. The physical properties, particle characteristics and chemical composition of PPWC filler and limestone filler were compared. Asphalt mastics were prepared with different filler-asphalt volume ratios (20%, 30% and 40%) and the physical properties, high-temperature rheological properties and low-temperature cracking resistance of asphalt mastics were tested. The experimental results showed that the surface of PPWC filler is rougher and has lower density and smaller particle size than limestone filler. When the filler content is the same, PPWC filler asphalt mastics have lower penetration and ductility, higher softening point than limestone filler asphalt mastics, and the viscosity of PPWC filler asphalt mastics is more sensitive than limestone filler asphalt mastics. PPWC filler asphalt mastics demonstrated superior high-temperature stability, but poorer low-temperature cracking resistance compared to limestone filler asphalt mastics. In conclusion, PPWC fillers can be used to replace limestone fillers in asphalt mixtures. The finding of this study will provide a new solution for the construction of eco-friendly roads.