Guaranteeing high-quality test solutions for Spin-Transfer Torque Magnetic RAM (STT-MRAM) is a must to speed up its high-volume production. A high test quality requires maximizing the fault coverage. Detecting permanent faults is relatively simple compared to intermittent faults; the latter are faults (caused by non-environmental conditions) that appear and disappear as a function of time, and are therefore hard to detect. Testing for such faults in STT-MRAMs is even worse considering the Magnetic Tunneling Junction inherent property ‘intrinsic switching stochasticity’, which results in inevitable random write errors. This paper presents a novel Design-for-Testability (DFT) scheme for detecting intermittent faults in STT-MRAMs; it is based on monitoring the write current. The strength of the write current is inversely correlated to the write error rate; when the write current is smaller than the specification, the device is considered faulty. A reduction in the write current can be caused by any defect in the write path of the memory (e.g., interconnects and contacts). Simulation results based on industrial design show that applying DFT yields a superior coverage of intermittent faults compared to functional test methods, such as march tests.@en

While Resistive RRAM (RRAM) offers attractive features for artificial neural networks (NN) such as low power operation and high-density, its conductance variation can pose significant challenges when the storage of synaptic weights is concerned. This paper reports an experimental evaluation of the conductance variations of manufactured RRAMs at the memory array level. Working at the memory array level allows to catch cycle-to-cycle (C2C) as well as device-to-device (D2D) variability and, hence, to propose a realistic evaluation of the conductance variation. Variability is evaluated with respect to the RRAM low resistance state (LRS) and high resistance state (HRS) conductance ratio. This ratio is selected as the parameter of interest as it guarantees the proper operation of the RRAM: the larger the ratio, the more reliable and robust the RRAM cell is in storing and retrieving data. The measurement results show that the conductance ratio is heavily affected by variability. Large spatial and temporal variations are reported, making challenging RRAM-based analog weight storage.

@en

Resistive Random Access Memories (RRAMs) are now undergoing commercialization, with substantial investment from many semiconductor companies. However, due to the immature manufacturing process, RRAMs are prone to exhibit unique defects, which should be efficiently identified for high-volume production. Hence, obtaining diagnostic solutions for RRAMs is necessary to facilitate yield learning, and improve RRAM quality. Recently, the Device-Aware Test (DAT) approach has been proposed as an effective method to detect unique defects in RRAMs. However, the DAT focuses more on developing defect models to aid production testing but does not focus on the distinctive features of defects to diagnose different defects. This paper proposes a Device-Aware Diagnosis method; it is based on the DAT approach, which is extended for diagnosis. The method aims to efficiently distinguish unique defects and conventional defects based on their features. To achieve this, we first define distinctive features of each defect based on physical analysis and characterizations. Then, we develop efficient diagnosis algorithms to extract electrical features and fault signatures for them. The simulation results show the effectiveness of the developed method to reliably diagnose all targeted defects.

@en

Due to the immature manufacturing process, Resistive Random Access Memories (RRAMs) are prone to exhibit new failure mechanisms and faults, which should be efficiently detected for high-volume production. Those unique faults are hard to detect but require specific Design-for-Test (DfT) circuit design. This paper proposes a DfT based on a parallel-reference write circuit that can detect all RRAM array faults during diagnosis, production testing, and its application in the field.@en

The development of Spin-Transfer Torque Magnetic RAMs (STT-MRAMs) mass production requires high-quality test solutions. Accurate and appropriate fault modeling is crucial for the realization of such solutions. This paper targets fault modeling and test generation for all interconnect and contact defects in STT-MRAMs and shows that using the defect injection and circuit simulation for fault modeling without incorporating the impact of magnetic coupling will result in an incomplete set of fault models; hence, not obtaining accurate fault models. Magnetic coupling introduced by the stray field is an inherent property of STT-MRAMs and may foster the occurrence of additional memory faults. Not considering the magnetic coupling clearly will give rise to test escapes. The paper introduces a compact model for STT-MRAM that incorporates the intra- and inter-cell stray field, uses this model to derive the full set of fault models for interconnect and contact defects, and finally proposes an efficient test solution.

@en

Resistive Random Access Memories (RRAMs) are being commercialized with significant investment from several semiconductor companies. In order to provide efficient and high-quality test solutions to push high-volume production, a comprehensive understanding of manufacturing defects is significantly required. This paper identifies and characterizes the over-RESET phenomenon based on silicon measurements. In our case study, 30% cycles suffered from intermittent extremely high resistance state exceeding the high resistance state criteria. The paper shows the limitations of conventional defect modeling based on linear resistors. To address this challenge, the Device-Aware (DA) defect modeling method is applied; a model of the defective RRAM device is developed and calibrated using measurements to accurately describe the impact of the defect on the electrical behavior of the memory device. Afterward, fault analysis is performed based on the DA defect model, and appropriate fault models are introduced; they show that the DA defect model will sensitize deep (extremely high resistance) state faults. Finally, dedicated test solutions for over-RESET devices are proposed.@en

Resistive Random Access Memory (RRAM) is a potential technology to replace conventional memories by providing low power consumption and high-density storage. As various manufacturing vendors make significant efforts to push it to high-volume production and commercialization, high-quality and efficient test solutions are of great importance. This paper analyzes interconnect and contact defects in RRAMs, while considering the impact of the memory Data Background (DB), and proposes test solutions. The complete interconnect and contact defect space in a layout-independent RRAM design is defined. Exhaustive defect injection and circuit simulation are performed in a systematic manner to derive appropriate fault models, not only for single-cell and two-cell coupling faults, but also for multi-cell coupling faults where the DBs are important. The results show the existence of unique 3-cell and 4-cell coupling faults due to e.g., the sneak path in the array induced by defects. These unique faults cannot be detected with traditional RRAM test solutions. Therefore, the paper introduces a test generation method that takes into account the DB, which is able to efficiently detect all these faults; hence, further improving the fault/defect coverage in RRAMs.@en

Many companies are heavily investing in the commercialization of Resistive Random Access Memories (RRAMs). This calls for a comprehensive understanding of manufacturing defects to develop efficient and high-quality test and diagnosis solutions to push high-volume production. This paper identifies and characterizes a new defect based on silicon measurements; the defect is called Ion Depletion (ID). In our case study, 45% cycles suffered from an intermittent reduction in high resistance state and did not impact low resistance state. The paper shows that the traditional fault modeling based on linear resistors as a defect model is not accurate. To address this challenge, the Device-Aware (DA) defect modeling method is applied; an RRAM model of the defective device is developed and calibrated using measurements to accurately describe the impact of the defect on the electrical behavior of the memory device. Afterward, fault analysis is performed based on the DA defect model, and appropriate fault models are introduced; they show that the ID defect may sensitize undefined state faults. Finally, dedicated test and diagnosis solutions for the ID defect are proposed.@en

The development of Spin-transfer torque magnetic RAM (STT-MRAM) mass production requires high-quality dedicated test solutions, for which understanding and modeling of manufacturing defects of the magnetic tunnel junction (MTJ) is crucial. This paper introduces and characterizes a new defect called Back-Hopping (BH); it also provides its fault models and test solutions. The BH defect causes MTJ state to oscillate during write operations, leading to write failures. The characterization of the defect is carried out based on manufactured MTJ devices. Due to the observed non-linear characteristics, the BH defect cannot be modelled with a linear resistance. Hence, device-aware defect modeling is applied by considering the intrinsic physical mechanisms; the model is then calibrated based on measurement data. Thereafter, the fault modeling and analysis is performed based on circuit-level simulations; new fault primitives/models are derived. These accurately describe the way the STT-MRAM behaves in the presence of BH defect. Finally, dedicated march test and a Design-for-Test solutions are proposed.

@en