Sodium hypochlorite (NaClO) is widely used for the chemical cleaning of fouled ultrafiltration (UF) membranes. Various studies performed on polymeric membranes demonstrate that long-term (>100 h) exposure to NaClO deteriorates the physicochemical properties of the membranes, leading to reduced performance and service life. However, the effect of NaClO cleaning on ceramic membranes, particularly the number of cleaning cycles they can undergo to alleviate irreversible fouling, remains poorly understood. Silicon carbide (SiC) membranes have garnered widespread attention for water and wastewater treatment, but their chemical stability in NaClO has not been studied. Low-pressure chemical vapor deposition (LP-CVD) provides a simple and economical route to prepare/modify ceramic membranes. As such, LP-CVD facilitates the preparation of SiC membranes: (a) in a single step; and (b) at much lower temperatures (700–900 °C) in comparison with sol-gel methods (ca. 2000 °C). In this work, SiC ultrafiltration (UF) membranes were prepared via LP-CVD at two different deposition temperatures and pressures. Subsequently, their chemical stability in NaClO was investigated over 200 h of aging. Afterward, the properties and performance of as-prepared SiC UF membranes were evaluated before and after aging to determine the optimal deposition conditions. Our results indicate that the SiC UF membrane prepared via LP-CVD at 860 °C and 100 mTorr exhibited excellent resistance to NaClO aging, while the membrane prepared at 750 °C and 600 mTorr significantly deteriorated. These findings not only highlight a novel preparation route for SiC membranes in a single step via LP-CVD, but also provide new insights about the careful selection of LP-CVD conditions for SiC membranes to ensure their long-term performance and robustness under harsh chemical cleaning conditions.@en

Long-term consumption of groundwater containing elevated levels of arsenic (As) can have severe health consequences, including cancer. To effectively remove As, conventional treatment technologies require expensive chemical oxidants to oxidise neutral arsenite (As(III)) in groundwater to negatively charged arsenate (As(V)), which is more easily removed. Rapid sand filter beds used in conventional aeration-filtration to treat anaerobic groundwater can naturally oxidise As(III) through biological processes but require an additional step to remove the generated As(V), adding complexity and cost. This study introduces a novel approach where As(V), produced through biological As(III) oxidation in a sand filter, is effectively removed within the same filter by embedding and operating an iron electrocoagulation (FeEC) system inside the filter. Operating FeEC within the biological filter achieved higher As(III) removal (81 %) compared to operating FeEC in the filter supernatant (67 %). This performance was similar to an analogous embedded-FeEC system treating As(V)-contaminated water (85 %), confirming the benefits of incorporating FeEC in a biological bed for comparable As(III) and As(V) removal. However, operating FeEC in the sand matrix consumed more energy (14 Wh/m³) compared to FeEC operated in a water matrix (7 Wh/m³). The efficiency of As removal increased and energy requirements decreased in such embedded-FeEC systems by deep-bed infiltration of Fe(III)-precipitates, which can be controlled by adjusting flow rate and pH. This study is one of the first to demonstrate the feasibility of embedding FeEC systems in sand filters for groundwater arsenic removal. Such systems capitalise on biological As(III) oxidation in aeration-filtration, effectively eliminating As(V) within the same setup without the need for chemicals or major modifications.

@en

Worldwide, a considerable amount of oily wastewater is generated, with oil droplets from 2 to 200 nm that are difficult to separate because of their size and colloidal stability. This study presents a novel approach for effectively separating microemulsions via cubic silicon carbide (3C-SiC)-coated alumina (Al ₂O ₃) membranes fabricated based on low pressure chemical vapor deposition (LPCVD). SiC was deposited at a relatively low temperature at 860 °C on 100 nm Al ₂O ₃ membranes using two precursors: SiH ₂Cl ₂ and C ₂H ₂. With the increase in deposition time, up to 25 min, the pore size decreased from 41 nm to 33 nm, which is a smaller pore size of a SiC membrane than previously used for oil/water separation. The polycrystalline 3C-SiC-coated membranes showed improved hydrophilicity (water contact angle of 15°) and highly negatively charged surfaces (−65 mV). Microemulsion filtration experiments were carried out at a constant permeate flux (80 Lm ⁻² h ⁻¹) for six cycles with varying deposition time, pH, surfactant types, and pore sizes. The fouling of the SiC-coated membrane was, compared to the Al ₂O ₃ membrane, effectively mitigated due to the enhanced electrostatic repulsion and hydrophilicity. Surfactant adsorption mainly occurred when the surface charge of the microemulsion and the membranes were opposite. Therefore, the surface charge of the alumina membrane changed from positive to negative when soaked in negatively charged microemulsions, whereas SiC-coated membranes remained negatively charged regardless of surfactant type. The membrane fouling was alleviated when the membrane and oil droplets had the same charge. Lastly, the 62 nm SiC-coated membrane with 20 min coating time was the best choice for the filtration of the microemulsion, because of the high rejection of the oil droplets and low fouling tendency.

@en

Ceramic nanofiltration is a potential one-step treatment for industrial waste streams. It can remove colloidal particles, oil droplets and some organic molecules. The drawback of the technology is that backwash cannot be applied to remove the accumulated cake layer from the membrane surface. At the moment only chemical cleaning with aggressive oxidizing agents like chlorine are effective to restore the permeability of the membranes after fouling. However, calcium carbonate (CaCO3) precoating has shown potential benefits in preliminary research, but have only been executed at laboratory scale, under a constant pressure and with a limited number of experimental cycles. In the presented work, the CaCO3 precoat/acid cleaning method was comprehensively studied under varying operational conditions. Dead-end filtration of a CaCO3-dispersion was used to precoat the membrane surface. Three different acids were tested to partly dissolve the precoat and remove the cake layer from the membrane surface. It was found that citric acid performed the best to recover the permeability of the membrane, probably due to the chelating properties, capturing the calcium ions, with a good removal of the cake layer during forward flush as a result. The size of precoat particles influenced the efficacy of permeability recovery. The smaller the deposited precoating particles on the membrane surface were, the better the cleaning effect was. It is expected that, when filtering real sewage water, these membranes can operate with one precoat during about 25 days with five consecutive citric acid cleaning cycles before a chlorine-based chemical treatment should thoroughly clean the membrane module.@en

Introduction:
Water scarcity is a significant global challenge that frequently manifests as inadequate water supply for domestic purposes. However, domestic water insecurity can occur even in regions where water is naturally abundant. Despite Colombia’s plentiful surface water resources, rural and peri-urban communities often experience limited access to water. Existing water supply systems are frequently susceptible to poor maintenance, particularly in remote areas where much of the infrastructure remains outdated. Consequently, water is often lost through leaks or unintentional non-domestic use. Although a regulatory framework for water usage exists, it does not consistently translate into effective implementation.

Methodology:
Based on an extensive survey of approximately 1000 households in four rural and four peri-urban communities in the Valle del Cauca Department, Colombia, we identified the factors underlying inefficient water supply and use. Perceived water use at the household level, based on self-reported time spent on various use types, such as bathing, and water supplied at the system level, was estimated.

Results and discussion:
Household size, education level, age and occupation were found to be critical factors influencing end water use and water supply. This not only elucidates why water is supplied and used inefficiently in rural systems (e.g., due to non-domestic use), but also accounts for the variability of perceived water use within peri-urban systems. The water use perceived by households in the rural systems was statistically similar across the rural systems studied and was significantly lower than that in the peri-urban systems. Most rural systems exhibited very low ratios of perceived water use to water supplied, indicating that either water is lost in conveyance or that water is used for non-domestic purposes. Peri-urban users, who perceived to use more water than users in rural areas, were associated with younger and more educated households. Higher education levels were also associated with better financial capacity and technical ability to manage water systems; therefore, peri-urban systems were better managed.@en

Activated carbon is employed for the adsorption of organic micropollutants (OMPs) from water, typically present in concentrations ranging from ng L⁻¹ to μg L⁻¹. However, the efficacy of OMP removal is considerably deteriorated due to competitive adsorption from background dissolved organic matter (DOM), present at substantially higher concentrations in mg L⁻¹. Interpreting the characteristics of competitive DOM is crucial in predicting OMP adsorption efficiencies across diverse natural waters. Molecular weight (MW), aromaticity, and polarity influence DOM competitiveness. Although the aromaticity-related metrics, such as UV₂₅₄, of low MW DOM were proposed to correlate with DOM competitiveness, the method suffers from limitations in understanding the interplay of polarity and aromaticity in determining DOM competitiveness. Here, we elucidate the intricate influence of aromaticity and polarity in low MW DOM competition, spanning from a fraction level to a compound level, by employing direct sample injection liquid chromatography coupled with ultrahigh-resolution Fourier-transform ion cyclotron resonance mass spectrometry. Anion exchange resin pre-treatment eliminated 93% of UV₂₅₄-active DOM, predominantly aromatic and polar DOM, and only minimally alleviated DOM competition. Molecular characterization revealed that nonpolar molecular formulas (constituting 26% PAC-adsorbable DOM) with medium aromaticity contributed more to the DOM competitiveness. Isomer-level analysis indicated that the competitiveness of highly aromatic LMW DOM compounds was strongly counterbalanced by increased polarity. Strong aromaticity-derived π-π interaction cannot facilitate the competitive adsorption of hydrophilic DOM compounds. Our results underscore the constraints of depending solely on aromaticity-based approaches as the exclusive interpretive measure for DOM competitiveness. In a broader context, this study demonstrates an effect-oriented DOM analysis, elucidating counterbalancing interactions of DOM molecular properties from fraction to compound level.

@en

A large decrease in permeability is often observed during the filtration of nano-sized colloids, while fouling is widely regarded as the main explanation for this phenomenon. The osmotic pressure or concentration polarization (CP) of colloids can also contribute to the flux decline. However, the contribution of CP to flux loss cannot be determined by the traditional CP model. In this study, the effect of fouling and CP/osmotic pressure on flux was distinguished. The CP values of polyethylene glycol (PEG) and silica-colloids were determined by the osmotic pressures near the membrane surface and in the feed. The CP induced by colloids accounted for 43–95% of the flux loss in our experiments. Silica exhibited higher CP values (127–460), compared to 7–71 for PEG. This was attributed to the slower back diffusion caused by the larger colloids, as evidenced by the diffusion coefficients of 4.30 × 10⁻¹¹ m²/s for silica (10 nm) and 1.45 × 10⁻¹⁰ m²/s for PEG (2.9 nm). Although the CP was mitigated by increasing the cross-flow velocity, CP values of 31 and 250 were observed for PEG and silica at high Reynolds number of 7317, respectively. The experimentally obtained CP values were also compared with those calculated by the film diffusion model.

@en

Ceramic nanofiltration (NF) is a promising alternative for direct surface water treatment, but is hampered for full-scale applications by fouling and a lack of eco-friendly cleaning regimes. In this work, an innovative reactive pre-coat layer, consisting of an iron oxychloride catalyst, was constructed on top of commercial ceramic NF membranes, for segregating a large-sized colloid fraction in canal water and Fenton cleaning with a hydrogen peroxide (H₂O₂) solution. The large-sized colloids (3−30 μm) were identified as dominant substances fouling the TiO₂ separation layer of the pristine membranes, leading to a fast increase in their filtration resistance, in contrast to the small-sized colloids (<0.04 μm) and natural organic matter (NOM). As a consequence, the catalyst pre-coat layer with a pore size of 0.1–0.5 μm was able to segregate the large-sized colloids from the TiO₂ separation layer during direct filtration of the raw water. Moreover, filtration under an acceptable flux of around 23 L m⁻² h⁻¹ did not cause pore clogging in the catalyst pre-coat. In addition, Fenton oxidation initiated by the catalytic pre-coat efficiently restored the filtration resistance, whereas sole H₂O₂ flush of the pristine membrane was not effective. In the meantime, the TiO₂ separation layer of the membrane exerted a high NOM rejection of approximately 90%, measured as dissolved organic carbon, while the catalyst pre-coat on the membrane remained active in Fenton cleaning, over five one-day cycles. The findings of this work may provide guidance on the structural and functional design of a catalytic pre-coat layer for a dual purpose of foulant segregation and oxidative removal, particularly in response to key fouling-causing substances, during membrane-based treatment of real water matrices.

@en

Membrane technology presents an effective solution for treating oily wastewater, a significant environmental hazard stemming from industries such as food processing, metalworking, and oil extraction. Compared to polymeric membranes, ceramic ones exhibit superior mechanical, chemical, and thermal stability, enabling more effective oil removal and easier cleaning. Despite their advantages, membrane fouling remains a challenge, impacting the efficiency of oily wastewater treatment. This review explores oily wastewater characteristics and ceramic membrane applications in treatment processes. It examines the factors influencing ceramic membrane fouling, including wastewater properties (e.g., oil concentration, pH), membrane characteristics (e.g., surface hydrophilicity, charge), and operational parameters (e.g., cross-flow velocity, permeate flux). Strategies to mitigate fouling, such as pretreatment, backpulsing/backwashing for sustained operation, and chemical cleaning for fouling removal, are discussed. By using pretreatment, membrane fouling can be reduced. Backpulsing/backwashing is effective to maintain a long-term operation. Chemical cleaning is effective in removing irreversible fouling and restoring the performance of the ceramic membranes. Moreover, membrane modification techniques that enhance performance are highlighted. Ultimately, the review identifies that effective fouling control is crucial for optimizing ceramic membrane use in oily wastewater treatment, underscoring the need for ongoing research in this area.

@en

The present study investigated the utilization of blood clam shells as a potential substitute for conventional media, as well as the influence of the acclimation time on the efficacy of an intermittent slow sand filter (ISSF) in the treatment of real domestic wastewater. ISSF was operated with 16 h on and 8 h off, focusing on the parameters of turbidity, ammonia, and phosphate. Two media combinations (only blood clam shells [CC] and sand + blood clam shells [SC]) were operated under two different acclimatization periods (14 and 28 d). Results showed that SC medium exhibited significantly higher removal of turbidity (p < 0.05) as compared to CC medium (45.99 ± 26.84 % vs. 3.79 ± 9.35 %), while CC exhibited slightly higher (p > 0.05) removal of ammonia (23.12 ± 20.2 % vs. 16.77 ± 16.8 %) and phosphate (18.03 ± 11.96 % vs 13.48 ± 12 %). Comparing the acclimatization periods, the 28 d of acclimatization period showed higher overall performances than the 14 d. Further optimizations need to be conducted to obtain an effluent value below the national permissible limit, since the ammonia and phosphate parameters are still slightly higher. SEM analysis confirmed the formation of biofilm on both mediums after 28 d of acclimatization; with further analysis of schmutzdecke formation need to be carried out to enrich the results.

@en

Verwijdering van organische microverontreinigingen uit huishoudelijk afvalwater, waaronder medicijnresten, staat sterk in de belangstelling om de oppervlaktewater kwaliteit te verbeteren, de drinkwaterbronnen te beschermen en te voldoen aan toekomstige EU richtlijnen. In minder dan vijf jaar is AdOx, een technologie waarin adsorptie en oxidatie word en gecombineerd, ontwikkeld tot een veelbelovende techniek. Ten opzichte van referentietechnieken zijn de CO2-voetafdruk klein en de kosten laag. De Nederlandse richtlijn van 70% verwijdering wordt gehaald. Ondanks het gebruik van ozon resulteert AdOx niet in bromaat vorming en oxidatiebijproducten in het behandelde afvalwater. Er is nog veel ruimte voor verdere optimalisatie.@en

Catalytic ceramic nanofiltration (NF) is a promising technology for direct wastewater reclamation, given its high separation selectivity and reactive surfaces for oxidative removal of fouling. A better understanding of the relation between fouling types and oxidative cleaning efficacy under high organic loading conditions is of practical importance for realizing stable filtration/cleaning performance in long-term water reclamation operations. In this work, Fenton cleaning, using a hydrogen peroxide solution and an iron oxychloride catalyst pre-coat layer on top of commercially available ceramic NF membranes, was studied with respect to high organic loaded fouling, simulated by a concentrated sodium alginate solution in the presence of calcium. Adsorption (in the absence of a permeate flow) and constant-pressure filtration (with a permeate flow) experiments were performed to distinguish between permeance decreases as a result of either adsorptive or cake layer fouling. The results show that the flux evolution could be divided into an initial sharp flux decline, due to rapid adsorption of the foulants, and a subsequent gradual flux decrease, resulting from progressive cake build-up on the membrane. The two-stage flux decrease was enhanced during the constant-pressure filtration experiments, because they start at a high flux with a high fouling rate, while the flux gradually decreases as fouling proceeds. During multiple adsorption/cake filtration/Fenton cleaning cycles, the cake layer fouling was sufficiently removed by Fenton cleaning in contrast to the adsorptive fouling. However, the total permeate production during ceramic NF was not influenced by the remaining adsorptive fouling (after cleaning), since the adsorptive fouling always only occurs at the beginning of each cycle. The findings provide new insights into the criteria for evaluating and optimizing the efficacy of oxidative (Fenton) cleaning during ceramic NF in water treatment.

@en

Biofilters are effectively used for drinking water treatment. However, the long ripening time of virgin media for manganese (Mn) removal is a major concern. In this study, the influence of the flow regime on the ripening time of virgin pumice medium was investigated. For this purpose, pilot-scale experiments were performed to compare the start-up of flow-through and recirculating filter columns using inherent inoculation with the same groundwater source. The systems were operated at 2 m·h¹ with gradual flow increments up to 5 m·h¹ and avoiding Fe-loading. Effective Mn removal (.90%) in flow-through and recirculating columns was achieved after 8 and 23 days, respectively. Flow-through columns reached compliance with a local drinking water criterion (Mn, 0.1 mg·L¹) at 15 cm filter depth in 11 days. Recirculating filter columns required 32 days to reach compliance at 30 cm depth. The start-up in recirculation regime resulted in a water consumption reduction of about 50% compared with flow-through regime. The intermittent provision of the Mn-loading in recirculating regime impacted the Mn-oxidizing bacteria (MOB) concentration in the pumice stone medium. Both flow regimes required a similar total Mn-loading (0.16 and 0.11 kg·Mn·m², respectively), suggesting that Mn-loading was the limiting factor for the ripening of pumice.

@en

There is a global need for optimizing the use of water that has resulted from increased demand due to industrial development, population growth, climate change and the pollution of natural water resources. One of the solutions is to use reclaimed water in industrial applications that do not require water of potable quality, such as cooling water. However, for cooling water, (treated) wastewater’s hardness is too high, apart from having a high load of suspended solids and organic matter. Therefore, a combination of softening with ceramic micro-filtration was proposed for treating wastewater treatment effluent containing fouling agents for potential use in industrial cooling systems. The effectiveness of the softening process on model-treated wastewater with calcium hydroxide in the presence of phosphate and sodium alginate was first evaluated using jar tests. Furthermore, membrane fouling was studied when filtering the softened water. The results showed that the inhibition of calcium carbonate precipitation occurred when inorganic substances, such as phosphate and organic compounds, were present in the water. The fouling of the membranes due to sodium alginate in water was only slightly negatively affected when combined with softening and phosphate. Therefore, this combination of treatments could be potentially helpful for the post-treatment of secondary effluent for cooling systems.@en

Groundwater contaminated with arsenic (As) must be treated prior to drinking, as human exposure to As at toxic levels can cause various diseases including cancer. Conventional aeration-filtration applied to anaerobic arsenite (As(III)) contaminated groundwater can remove As(III) by co-oxidizing native iron (Fe(II)) and As(III) with oxygen (O₂). However, the As(III) removal efficiency of conventional aeration can be low, in part, because of incomplete As(III) oxidation to readily-sorbed arsenate (As(V)). In this work, we investigated a new approach to enhance As(III) co-removal with native Fe(II) by the anaerobic addition of hydrogen peroxide (H₂O₂) prior to aeration. Experiments were performed to co-oxidize Fe(II) and As(III) with H₂O₂ (anaerobically), O₂ (aerobically), and by sequentially adding of H₂O₂ and O₂. Aqueous As(III) and As(V) measurements after the reaction were coupled with solid-phase speciation by Fe and As K-edge X-ray absorption spectroscopy (XAS). We found that complete anaerobic oxidation of 100 µM Fe(II) with 100 µM H₂O₂ resulted in co-removal of 95% of 7 µM As(III) compared to 44% with 8.0-9.0 mg/L dissolved O₂. Furthermore, we found that with 100 µM Fe(II), the initial Fe(II):H₂O₂ ratio was a critical parameter to remove 7 µM As(III) to below the 10 µg/L (0.13 µM) WHO guideline, where ratios of 1:4 (mol:mol) Fe(II):H₂O₂ led to As(III) removal matching that of 7 µM As(V). The improved As(III) removal with H₂O₂ was found to occur partly because of the well-established enhanced efficiency of As(III) oxidation in Fe(II)+H₂O₂ systems relatively to Fe(II)+O₂ systems. However, the XAS results unambiguously demonstrated that a large factor in the improved As(III) removal was also due to a systematic decrease in crystallinity, and thus increase in specific surface area, of the generated Fe(III) (oxyhydr)oxides from lepidocrocite in the Fe(II)+O₂ system to poorly-ordered Fe(III) precipitates in the Fe(II)+H₂O₂ system. The combined roles of H₂O₂ (enhanced As(III) oxidation and structural modification) can be easily overlooked when only aqueous species are measured, but this dual impact must be considered for accurate predictions of As removal in groundwater treatment.

@en

AdOx is een combinatie van een adsorptieproces en een oxidatietechniek. Een veelbelovende technologie om medicijnresten uit afvalwater te halen. En winnaar van de Waterinnovatieprijs 2021, categorie Gezond Water en Gezonde Bodem.@en

Endogeneity or reverse causality in regression analysis results in biased estimation of the effects of independent variables on the dependent variable and leads to inaccurate interpretations. However, the biased estimation of the effects of psychological factors on water–related behaviours are rarely discussed. This study investigated the endogeneity of psychological factors in water-related behaviour using an instrument variable (IV) approach. Data from eight household water treatment (HWT) studies in Asia, Africa, and South America were utilized. A combination of several socio-economic characteristics, such as education and accessibility, was used as a control variable and three psychological factors, i.e., perception of risk, attitude towards HWT, and social norms, were used as the predictors of the adoption of HWT. Variables related to institutional quality of the countries, based on the World Governance Indicators of the World Bank were used as IVs to predict the psychological factors. The results suggest that endogeneity exists in water-related behavioural studies. Institutions were found to be valid IV for psychological factors attitude and norms, but not for the perception of risk. This suggests that the institutional quality influences households’ attitude and norms regarding behaviour. If the feedback effect of actual behaviour on the psychological factors were not considered, the effects of attitude and norms on HWT adoption were underestimated by 59% and 40%, respectively. Finally, despite the challenge of finding valid IV, the endogeneity effect of psychological factors needs to be controlled when estimating the effect of psychological factors on water-related behaviour in future water-related behavioural studies.

@en

Ceramic membranes have drawn increasing attention in oily wastewater treatment as an alternative to their traditional polymeric counterparts, yet persistent membrane fouling is still one of the largest challenges. Particularly, little is known about ceramic membrane fouling by oil-in-water (O/W) emulsions in constant flux filtration modes. In this study, the effects of emulsion chemistry (surfactant concentration, pH, salinity and Ca²⁺) and operation parameters (permeate flux and filtration time) were comparatively evaluated for alumina and silicon carbide (SiC) deposited ceramic membranes, with different physicochemical surface properties. The original membranes were made of 100% alumina, while the same membranes were also deposited with a SiC layer to change the surface charge and hydrophilicity. The SiC-deposited membrane showed a lower reversible and irreversible fouling when permeate flux was below 110 L m⁻² h⁻¹. In addition, it exhibited a higher permeance recovery after physical and chemical cleaning, as compared to the alumina membranes. Increasing sodium dodecyl sulfate (SDS) concentration in the feed decreased the fouling of both membranes, but to a higher extent in the alumina membranes. The fouling of both membranes could be reduced with increasing the pH of the emulsion due to the enhanced electrostatic repulsion between oil droplets and membrane surface. Because of the screening of surface charge in a high salinity solution (100 mM NaCl), only a small difference in irreversible fouling was observed for alumina and SiC-deposited membranes under these conditions. The presence of Ca²⁺ in the emulsion led to high irreversible fouling of both membranes, because of the compression of diffusion double layer and the interactions between Ca²⁺ and SDS. The low fouling tendency and/or high cleaning efficiency of the SiC-deposited membranes indicated their potential for oily wastewater treatment.

@en

Sequential iron (as Fe²⁺) oxidation has been found to yield improved arsenic (as As(III)) uptake than the single-step oxidation. The objective of this study was to gain a better understanding of interactions with phosphate (PO₄³⁻) and silicate (SiO₄²⁻) during sequential Fe²⁺ and As(III) oxidation and removal, as these are typically found in groundwater and known to interfere with As removal. The laboratory experiments were performed using single and multi-step jar tests with an initial As(III/V), Fe²⁺, PO₄³⁻, SiO₄²⁻ concentrations, and pH of 200 μg/L, 2.5 mg/L, 2 mg/L, 16 mg/L and 7.0, respectively representing the targeted natural groundwater in Rajshahi district, Bangladesh. The sequential Fe²⁺ and As(III) oxidation in the multi-step jar tests indicated that the PO₄³⁻ hindrance on As removal in the first Fe²⁺ oxidation step was compensated for in the second. Moreover, smaller Fe flocs (<0.45 μm) were observed in the presence of SiO₄²⁻, potentially providing more surface area during the second Fe²⁺ oxidation step leading to better overall As removal. Altogether it may be concluded that controlling the As(III) and Fe²⁺ oxidation sequence is beneficial for As removal compared to single-step Fe²⁺ oxidation, both in the presence and absence of PO₄³⁻ and/or SiO₄²⁻.

@en

It was widely acknowledged that dissolved organic matter (DOM) in natural water has ubiquitous competitiveness against organic micropollutants (OMPs) during adsorption onto activated carbon. However, some (model) low molecular weight organics have been reported to adsorb onto activated carbon, but were not competitive against co-adsorbates. The objective of this study is to identify which adsorbable DOM fractions in natural water contribute to the DOM competitiveness, and what is the impact of the OMP adsorbability and initial OMP concentration on this competitiveness. We, therefore, disassociated the adsorption of DOM fractions and OMPs (carbamazepine, caffeine and sulfamethoxazole) using a two-stage adsorption procedure, removing various adsorbable DOM fractions with powdered activated carbon pretreatment and then unraveling the competitiveness against OMPs of the remaining DOM. Our results demonstrated that DOM competition was not ubiquitous for all adsorbable fractions in natural water, and ∼ 25% of the adsorbable DOM was not competitive. The poorly adsorbable DOM was shown to be a non-competitive co-adsorbate, and its complexation even elevated the adsorption capacity of one of the OMPs (carbamazepine). The amount of DOM competitors increased for weaker adsorbable OMPs, and at higher initial OMP concentrations. The variability in DOM competition, differentiated by DOM adsorbability, has advanced the understanding of DOM competition, from ubiquitous competition to variable roles (varying competitiveness/complementary adsorption) of differently adsorbable DOM fractions during OMP adsorption.

@en