Rebar-reinforced coarse aggregate ultra-high-performance concrete (R-CA-UHPC) has been used in the construction of new structures and strengthening of deteriorated aged infrastructures, and it inevitably sustains tension. To study the tensile behavior of R-CA-UHPC members, axial tensile tests for dog-bone-shaped specimens were designed and conducted. The investigated variables included reinforcement ratio in terms of rebar quantity/diameter, and concrete type (CA-UHPC vs. normal concrete). The test results showed that the improved rebar/CA-UHPC bond property prevents the emergence of splitting cracks, but intensifies the crack localization for CA-UHPC and strain concentration for rebar after yielding. Moreover, the restrained effect of rebar on free shrinkage of CA-UHPC leads to a decrease in the first cracking strength for R-CA-UHPC members. Based on the established development functions of elastic modulus, autogenous shrinkage, and tensile creep for CA-UHPC, the restrained effect was quantified according to Dischinger's-differential-equation-based theoretical analysis. Finally, the models to predict the first cracking stresses/strains and the yielding loads of the R-CA-UHPC members were developed and validated.@en

The article ‘Effect of matrix self-healing on the bond-slip behavior of micro steel fibers in ultra-high-performance concrete’, written by Salam Al-Obaidi, Shan He, Erik Schlangen and Liberato Ferrara, was originally published in volume 56, issue 9, article 161 without Open Access.

@en

This study investigates the bond-slip behavior of micro steel fibers embedded into an Ultra-High-Performance Concrete (UHPC) matrix as affected by the self-healing of the same matrix in different exposure conditions. The UHPC matrix contains a crystalline admixture as a promoter of the autogenous self-healing specially added to enhance the durability in the cracked state. For the aforesaid purpose, some samples were partially pre-damaged with controlled preload (fiber pre-slip at different levels) and subjected to one-month exposure in 3.5% NaCl aqueous solution and in tap water to study the fiber corrosion, if any, and the effects of self-healing; after that, they were subjected to a pull-out test, to be compared with the behavior of analogous non-pre-slipped samples undergoing the same curing history. Moreover, some samples were cured in the chloride solution, intended to simulate a marine environment, to study the effect of marine curing on the pull-out behavior of steel fiber. The steel fiber corrosion and self-healing products attached to the surface of the steel fiber were analyzed via Scanning Electron Microscopy (SEM), and Energy -Dispersive Spectroscopy (EDS). The results indicate that the newly healed particles formed on the highly damaged fiber-matrix interface significantly enhance the friction phase of the bond-slip behavior and result in a significant residual capacity compared to non-pre-slipped specimens. On the other hand, the self-healing effect in specimens subjected to low damage pre-slip contributed more to the chemical adhesion region of the bond-slip behavior. Owning to the dense microstructure of the matrix, curing in 3.5% NaCl aqueous solution was not found to significantly affect the pull-out resistance as compared to the samples cured in tap water.

@en

The form freedom enabled by digital fabrication with concrete technologies provides advantages for a wide range of concrete based objects, from architectural to structural elements. The current chapter focuses on the specifics of structural design and engineering of DFC with emphasis on those technologies based on Additive Manufacturing with extrusion. Since it is a new and innovative way to build, a clear common approach to structural engineering has not yet been developed. As a result, this chapter aims to introduce the specific challenges of structural design and engineering with the additive manufacturing technology, providing an overview of structural typologies that have been developed (especially concerning the reinforcement strategies, including fibre reinforcement). Furthermore, the structural principles adopted in DFC and the codified approaches used in conventional reinforced concrete is compared, and putative structural testing procedures and validation methods for DFC are reported.@en

The fib Model Codes aim at integrating in a single document the relevant knowledge for the structural design with concrete. Fibre reinforced concrete is already integrated in fib Model Code 2010 (fib MC2010) as a general category of materials. The group of flowable concrete consists of clusters of different types of concrete among others Self-Compacting Concrete, Ultra High Performance Concrete and Strain-Hardening Cementitious Composites. Being highly flowable is the distinguishing characteristic, flowable concrete might contain or not contain fibres. Although the fibre contribution on the structural level can be assessed on short-term, the structural behaviour also depends on the behaviour of the fibres and the matrix in which they are embedded. fib Task Group 4.3 worked on identifying and characterising different types of flowable concrete and discusses in a fib bulletin the most relevant aspects with regard to mix design, manufacturing, material performance and structural behaviour of flowable concrete which can allow innovative applications to be developed and realised. This paper discusses recent developments with regard to flowable concrete in a broader perspective and addresses the progress with regard to standardisation.@en

The increasing concern for safety and sustainability of structures is calling for the development of smart self-healing materials and preventive repair methods. The appearance of small cracks (<300 µm in width) in concrete is almost unavoidable, not necessarily causing a risk of collapse for the structure, but surely impairing its functionality, accelerating its degradation, and diminishing its service life and sustainability. This review provides the state-of-the-art of recent developments of self-healing concrete, covering autogenous or intrinsic healing of traditional concrete followed by stimulated autogenous healing via use of mineral additives, crystalline admixtures or (superabsorbent) polymers, and subsequently autonomous self-healing mechanisms, i.e. via, application of micro-, macro-, or vascular encapsulated polymers, minerals, or bacteria. The (stimulated) autogenous mechanisms are generally limited to healing crack widths of about 100–150 µm. In contrast, most autonomous self-healing mechanisms can heal cracks of 300 µm, even sometimes up to more than 1 mm, and usually act faster. After explaining the basic concept for each self-healing technique, the most recent advances are collected, explaining the progress and current limitations, to provide insights toward the future developments. This review addresses the research needs required to remove hindrances that limit market penetration of self-healing concrete technologies.@en