Rapid sand filters (RSF) are an established and widely applied technology for groundwater treatment. Yet, the underlying interwoven biological and physical-chemical reactions controlling the sequential removal of iron, ammonia and manganese remain poorly understood. To resolve the contribution and interactions between the individual reactions, we studied two full-scale drinking water treatment plant configurations, namely (i) one dual-media (anthracite and quartz sand) filter and (ii) two single-media (quartz sand) filters in series. In situ and ex situ activity tests were combined with mineral coating characterization and metagenome-guided metaproteomics along the depth of each filter. Both plants exhibited comparable performances and process compartmentalization, with most of ammonium and manganese removal occurring only after complete iron depletion. The homogeneity of the media coating and genome-based microbial composition within each compartment highlighted the effect of backwashing, namely the complete vertical mixing of the filter media. In stark contrast to this homogeneity, the removal of the contaminants was strongly stratified within each compartment, and decreased along the filter height. This apparent and longstanding conflict was resolved by quantifying the expressed proteome at different filter heights, revealing a consistent stratification of proteins catalysing ammonia oxidation and protein-based relative abundances of nitrifying genera (up to 2 orders of magnitude difference between top and bottom samples). This implies that microorganisms adapt their protein pool to the available nutrient load at a faster rate than the backwash mixing frequency. Ultimately, these results show the unique and complementary potential of metaproteomics to understand metabolic adaptations and interactions in highly dynamic ecosystems.

Iron in anaerobic groundwater is commonly removed by oxidation followed by sand filtration. This produces large volumes of iron(III)(hydr)oxide sludge with little value. Our research investigates the novel concept of anaerobic iron(II) recovery from groundwater as the valuable mineral vivianite (Fe₃(PO₄)₂ • 8 H₂O) by the addition of phosphate to the water. We found that vivianite precipitated both in synthetic and natural groundwater when the saturation index (SI) was higher than 4. The SI can be increased by elevating the pH, which allows for iron removal at lower concentrations. Anaerobic iron removal reached 93.7% in natural groundwater, which increased further to 99.9% after a subsequent aeration step. Vivianite precipitation followed second order kinetics with a rate constant of 2.3 M⁻¹s⁻¹ and the sludge volume decreased by two third compared to iron oxidation. We therefore conclude that anaerobic iron removal is a promising new approach towards sustainable groundwater treatment.

Iron-electrocoagulation is a promising contaminant (e.g. arsenic) removal technology that is based on electrochemical Fe(II) production from steel electrodes and subsequent transport of Fe(II) to the bulk solution, where contaminant removal occurs. Although Fe-electrocoagulation systems have been shown to effectively remove contaminants in extended field trials, the efficiency of field systems can be lower than in laboratory studies. One hypothesis for this disparity is that the Faradaic efficiency of short-term laboratory experiments is higher than field systems operated over extended periods. The Faradaic efficiency is a pivotal performance indicator that we define as the measured Fe dosage normalized by the theoretical Fe dosage calculated by Faraday's law. In this work, we investigated the Faradaic efficiency in laboratory experiments for up to 35 operating cycles (>2 months) with varied Fe(0) anode purity, charge dosage rate, and electrolyte composition. Our results showed that the Faradaic efficiency decreased continuously during repeated operation under typical field conditions (charge dosage rate = 4 C/L/min, synthetic groundwater) regardless of the Fe(0) anode purity, leading to a Faradaic efficiency ≈ 0.6 after 2 months. By contrast, increasing the charge dosage rate to ≥15 C/L/min produced a Faradaic efficiency >0.85 over the entire experiment for both Fe(0) anode purities. Electrolyte solutions free of oxyanions also resulted in sustained Faradaic efficiency >0.85, regardless of the charge dosage rate. Our results confirm a previously proposed relationship between low Faradaic efficiency and the formation of macroscopic electrode surface layers, which consist of Fe (oxyhydr)oxides on the anode and a mixture of Fe (oxyhydr)oxides and calcite on the cathode. Based on these results, we discuss potential strategies to maintain a high Faradaic efficiency during Fe-electrocoagulation field treatment.