We have designed and realized a temperature and pressure controlled cell for Neutron Reflectometry (NR) and Small Angle Neutron Scattering (SANS) that is compatible with simultaneous optical transmission and resistivity measurements. The cell can accommodate samples up to 102 mm (4 inch) in diameter, can be pressurized from vacuum up to 10 bar gas pressure and the sample temperature can be controlled up to 350°C. The four single crystal quartz windows ensure both a good neutron and optical transmission and hence can be used in combination with in-situ optical transmission measurements. We present the cell and illustrate its performance with a series of neutron reflectometry experiments performed on Ta based thin films under a hydrogen containing atmosphere.

@en

Achieving both high redox activity and rapid ion transport is a critical and pervasive challenge in electrochemical energy storage applications. This challenge is significantly magnified when using large-sized charge carriers, such as the sustainable ammonium ion (NH₄⁺). A self-assembled MXene/n-type conjugated polyelectrolyte (CPE) superlattice-like heterostructure that enables redox-active, fast, and reversible ammonium storage is reported. The superlattice-like structure persists as the CPE:MXene ratio increases, accompanied by a linear increase in the interlayer spacing of MXene flakes and a greater overlap of CPEs. Concurrently, the redox activity per unit of CPE unexpectedly intensifies, a phenomenon that can be explained by the enhanced de-solvation of ammonium due to the increased volume of 3 Å-sized pores, as indicated by molecular dynamic simulations. At the maximum CPE mass loading (MXene:CPE ratio = 2:1), the heterostructure demonstrates the strongest polymeric redox activity with a high ammonium storage capacity of 126.1 C g⁻¹ and a superior rate capability at 10 A g⁻¹. This work unveils an effective strategy for designing tunable superlattice-like heterostructures to enhance redox activity and achieve rapid charge transfer for ions beyond lithium.

@en

Mixed Sn-Pb halide perovskites are promising absorber materials for solar cells due to the possibility of tuning the bandgap energy down to 1.2-1.3 eV. However, tin-containing perovskites are susceptible to oxidation affecting the optoelectronic properties. In this work, we investigated qualitatively and quantitatively metastable oxygen-induced doping in isolated ASn_xPb_1-xI₃ (where A is methylammonium or a mixture of formamidinium and cesium) perovskite thin films by means of microwave conductivity, structural and optical characterization techniques. We observe that longer oxygen exposure times lead to progressively higher dark conductivities, which slowly decay back to their original levels over days. Here oxygen acts as an electron acceptor, leading to tin oxidation from Sn²⁺ to Sn⁴⁺ and creation of free holes. The metastable oxygen-induced doping is enhanced by exposing the perovskite simultaneously to oxygen and light. Next, we show that doping not only leads to the reduction in the photoconductivity signal but also induces long-term effects even after loss of doping, which is thought to derive from consecutive oxidation reactions leading to the formation of defect states. On prolonged exposure to oxygen and light, optical and structural changes can be observed and related to the formation of SnO_x and loss of iodide near the surface. Our work highlights that even a short-term exposure to oxygen immediately impairs the charge carrier dynamics of the perovskite, while structural perovskite degradation is only noticeable upon long-term exposure and accumulation of oxidation products. Hence, for efficient solar cells, exposure of mixed Sn-Pb perovskites to oxygen during production and operation should be rigorously blocked.

@en

Lithium metal with its high theoretical capacity and low negative potential is considered one of the most important candidates to raise the energy density of all-solid-state batteries. However, lithium filament growth and its induced solid electrolyte decomposition pose severe challenges to realize a long cycle life. Here, dendrite growth in solid-state Li metal batteries is alleviated by introducing a high dielectric material, barium titanate, as a filler that removes the electric field gradients that catalyze dendrite formation. In symmetrical Li-metal cells, this results in a very small over-potential of only 48 mV at a relatively high current density of 1 mA cm⁻², when cycling a capacity of 2 mA h cm⁻² during 1700 h. The high dielectric filler improves the Coulombic efficiency and cycle life of full cells and suppresses electrolyte decomposition as indicated by solid-state nuclear magnetic resonance (NMR) and X-ray photoelectron spectroscopy (XPS) measurements. This indicates that the high dielectric filler can suppress dendrite formation, thereby reducing solid electrolyte decomposition reactions, resulting in the observed low overpotentials and improved cycling efficiency.

@en

At ambient conditions, rare-earth oxyhydride thin films show reversible photochromism and photoconductivity, while their mechanism and relation are still unclear. In this work, this question is explored with in situ time-resolved measurements of both optical and transport properties of Gd-based oxyhydride thin films. It is found that p-type large polaron conduction is the initial mechanism of charge transport; however, upon photo-darkening, a 10⁴-fold increase of conductivity occurs, and n-type carriers become dominant. Further, photochromism and photoconductivity are shown to originate from a single process, as indicated by the fact that the photoconductivity is exponentially proportional to the increase of optical absorption. This exponential relation, notably, cannot stem from any of the optically absorbing species thought responsible for photochromism and, therefore, suggests that their formation is accompanied by a concerted increase of negative charge carriers in the Gd oxyhydride films.

@en

Silicon-aluminum-oxigen (SiAlO) coatings doped with Sm²⁺ and prepared by reactive magnetron co-sputtering of Si, Al, and Sm targets, are attractive for luminescence solar concentrator applications but suffer from the low absorption between 300 and 600 nm. This article reports that the main cause of low absorption is a high concentration of undesired Sm³⁺. This finding is supported by optical transmittance, photoluminescence emission and excitation characterization, and X-ray photoelectron spectroscopy data of the Sm's 3d^5/2 edge. We present an alternative deposition process for obtaining Sm doped SiAlO layers with enhanced Sm²⁺ absorption by incorporating Sm through the use of multilayer thin-film precursors composed of metallic Sm and SiAlO layers. After thermal post-deposition treatments, diffusion and reaction of the metallic Sm layers with the SiAlO host results in coatings showing the characteristic 5d → 4f transitions of Sm²⁺ in the region between 250 and 600 nm which were not detectable in Sm-doped single layers. This same deposition strategy produces Tm doped SiAlO coatings with Tm²⁺‘s characteristic luminescence at 1132 nm when the SiAlO host is in the mullite composition region. The photoluminescence excitation spectrum of Tm²⁺ is compared to phosphor with similar composition and covers the range between 300 and 700 nm.

@en

The electrochemical nitrogen reduction reaction (NRR) is a promising alternative to the current greenhouse gas emission intensive process to produce ammonia (NH₃) from nitrogen (N₂). However, finding an electrocatalyst that promotes NRR over the competing hydrogen evolution reaction (HER) has proven to be difficult. This difficulty could potentially be addressed by accelerating the electrocatalyst development for NRR by orders of magnitude using high-throughput (HTP) workflows. In this work, we developed a HTP gas diffusion electrode (GDE) cell to screen up to 16 electrocatalysts in parallel. The key innovation of the cell is the use of expanded Polytetrafluoroethylene (ePTFE) gas diffusion layers (GDL) which simplifies the handling of catalyst arrays compared to carbon fabrics and enables sufficient N₂ mass transport. We demonstrate the robustness of the HTP workflow by screening 528 bimetallic catalysts of composition AB (A,B = Ag, Al, Au, Co, Cu, Fe, Mn, Mo, Ni, Pd, Re, Ru, W) for NRR activity. None of the materials produced ammonia significantly over background level which emphasizes the difficulty of finding active electrocatalysts for NRR and narrows down the search space for future studies.

@en

In this study, different surface pretreatments were applied to clean and activate titanium alloy surfaces. The samples were subjected to grit blasting treatments using two different pressures and afterwards, a UV/Ozone treatment was applied at different times to study the wettability and surface oxidation of the titanium samples. Scanning electron microscopy and laser confocal microscopy showed the surface morphology and the increased roughness with grit blasting pressure. X-ray Photoelectron Spectroscopy revealed that titanium was increasingly oxidized with increasing UV/Ozone treatment time, which leads to a reduced contact angle and a better adhesive performance in a butt tension test proving the effectivity of this surface treatment for titanium. Furthermore, the addition of sol-gel AC-120 and corrosion inhibition primer BR 6747 showed to be an additional improvement in the initial adhesion and after different degrees of aging by exposure to salt-spray, making the surface treatment techniques used in this research, a promising environmental friendly alternative to improve adhesive bonding performance.

@en

Catalyzing capping layers on metal hydrides are employed to enhance the hydrogenation kinetics of metal hydride-based systems such as hydrogen sensors. Here, we use a novel experimental method to study the hydrogenation kinetics of catalyzing capping layers composed of several alloys of Pd and Au as well as Pt, Ni, and Ru, all with and without an additional PTFE polymer protection layer and under the same set of experimental conditions. In particular, we employ a thin Ta film as an optical indicator to study the kinetics of the catalytic layers deposited on top of it and which allows one to determine the absolute hydrogenation rates. Our results demonstrate that doping Pd with Au results in significantly faster hydrogenation kinetics, with response times up to five times shorter than Pd through enhanced diffusion and a reduction in the activation energy. On the other hand, the kinetics of non-Pd-based materials turn out to be significantly slower and mainly limited by the diffusion through the capping layer itself. Surprisingly, the additional PTFE layer was only found to improve the kinetics of Pd-based capping materials and has no significant effect on the kinetics of Pt, Ni, and Ru. Taken together, the experimental results aid in rationally choosing a suitable capping material for the application of metal hydrides and other materials in a hydrogen economy. In addition, the used method can be applied to simultaneously study the hydrogenation kinetics in thin-film materials for a wide set of experimental conditions.@en

Direct electrochemical nitrogen reduction holds the promise of enabling the production of carbon emission-free ammonia, which is an important intermediate in the fertilizer industry and a potential green energy carrier. Here we show a strategy for ambient condition ammonia synthesis using a hydrogen permeable nickel membrane/electrode that spatially separates the electrolyte and hydrogen reduction side from the dinitrogen activation and hydrogenation sites. Gaseous ammonia is produced catalytically in the absence of electrolyte via hydrogenation of adsorbed nitrogen by electrochemically permeating atomic hydrogen from water reduction. Dinitrogen activation at the polycrystalline nickel surface is confirmed with 15N2 isotope labeling experiments, and it is attributed to a Mars-van Krevelen mechanism enabled by the formation of N-vacancies upon hydrogenation of surface nitrides. We further show that gaseous hydrogen does not hydrogenate the adsorbed nitrogen, strengthening the benefit of having an atomic hydrogen permeable electrode. The proposed approach opens new directions toward green ammonia.

@en

Wide-band-gap perovskites such as methylammonium lead bromide (MAPB) are promising materials for tandem solar cells because of their potentially high open-circuit voltage, which is yet still far below the maximum limit. The relatively short charge-carrier lifetimes deduced from time-resolved photoluminescence (TRPL) measurements seem in strong contrast with the long lifetimes observed with time-resolved photoconductance measurements. This is explained by a large amount of hole defect states, NT > 1016 cm-3, in spin-coated layers of MAPB residing at or near the grain boundaries. The introduction of hypophosphorous acid (HPA) increases the average grain size by a factor of 3 and reduces the total concentration of the trap states by a factor of 10. The introduction of HPA also increases the fraction of initially generated holes that undergo charge transfer to the selective contact, Spiro-OMeTAD (SO), by an order of magnitude. In contrast to methylammonium lead iodide (MAPI)/SO bilayers, a reduction of the carrier lifetime is observed in MAPB/SO bilayers, which is attributed to the fact that injected holes undergo interfacial recombination via these trap states. Our findings provide valuable insight into the optoelectronic properties of bromide-containing lead halide perovskites essential for designing efficient tandem solar cells.

@en

Chemical vapour deposition (CVD) has emerged as the dominant technique to combine high quality with large scale production of graphene. The key challenge for CVD graphene remains the transfer of the film from the growth substrate to the target substrate while preserving the quality of the material. Avoiding the transfer process of single or multi-layered graphene (SLG-MLG) has recently garnered much more interest. Here we report an original method to obtain a 4-inch wafer fully covered by MLG without any transfer step from the growth substrate. We prove that the MLG is completely released on the oxidized silicon wafer. A hydrogen peroxide solution is used to etch the molybdenum layer, used as a catalyst for the MLG growth via CVD. X-ray photoelectron spectroscopy proves that the layer of Mo is etched away and no residues of Mo are trapped beneath MLG. Terahertz transmission near-field imaging as well as Raman spectroscopy and atomic force microscopy show the homogeneity of the MLG film on the entire wafer after the Mo layer etch. These results mark a significant step forward for numerous applications of SLG-MLG on wafer scale, ranging from micro/nano-fabrication to solar cells technology.

@en

This paper describes a novel method to fabricate porous graphene oxide (PGO) from GO by exposure to oxygen plasma. Compared to other methods to fabricate PGO described so far, e.g. the thermal and steam etching methods, oxygen plasma etching method is much faster. We studied the development of the porosity with exposure time using atomic force microscopy (AFM). It was found that the development of PGO upon oxygen-plasma exposure can be controlled by tapping mode AFM scanning using a Si tip. AFM tapping stalls the growth of pores upon further plasma exposure at a level that coincides with the fraction of sp² carbons in the GO starting material. We suggest that AFM tapping procedure changes the bond structure of the intermediate PGO structure, and these stabilized PGO structures cannot be further etched by oxygen plasma. This constitutes the first report of tapping AFM as a tool for local mechano-chemistry.

@en