With the rapid urbanization and development of metropolises, urban road tunnels have been constructed at an increasing rate, significantly alleviating urban traffic pressure, and improving urban resilience. Fire hazards have become a major threat to modern road tunnels due to the growing popularity of electric vehicles and high-density transportation of goods, particularly flammable materials. Asphalt pavements, as an essential component of road tunnels, may release harmful effluences and smoke under high temperatures, exacerbating the fire and adding risk to life safety. It is hence critical to investigate fire-retarding asphalt materials and their potential use in urban road tunnels pavements. This paper provides a comprehensive review of fire-retarding asphalt pavements for urban road tunnel pavements. The review covers tunnel fire generation mechanisms, evaluation methods, flame retardants for asphalt pavements, and recent developments in flame retardant technologies. By investigating these aspects, this paper aims to better understand the flammability of asphalt mixtures and asphalt pavements in urban road tunnels, promote the research of flame-retardant technology, and ultimately reduce the damage and loss caused by asphalt road tunnel fire accidents. Additionally, this study identifies the limitations of current research and provides an outlook for future research to contribute to the resilience of urban road tunnel structures and the longer service life of asphalt pavement in semi-closed road tunnels.

@en

Polycyclic Aromatic Hydrocarbons (PAHs) in asphalt materials is a type of serious environmental hazard, and the main pollution resource in road engineering. Aiming at the requirement of PAHs rapid detection method in asphalt pavement construction for low environmental hazard, this research concentrated in experiments about PAHs content, fluorescence characteristics, solvent environment impact mechanism and correlation between fluorescence intensity and concentration in different asphalt materials, based on the fluorescence effect of PAHs from condensed ring structure. It is found that coal tar asphalt has a typical aggregation-caused quenching phenomenon and higher fluorescence quantum efficiency. Taking the three solvent environment parameters polarity, viscosity and pH value as the research objects, the optimal solvent environment for the fluorescence phenomenon of PAHs in asphalt materials was explored and established as dimethyl sulfoxide: tetrahydrofuran: deionized water: glycerol = 1 : 1 : 1 : 2. Under the optimal solvent environment, fluorescence intensity and concentration of the three asphalt materials all showed obvious linear relationship. Under the same concentration condition, fluorescence intensity of asphalt material showed positive correlation with the PAHs content. This study proves that the asphalt material has the linear relationship between fluorescence intensity and PAHs concentration, which will provide theoretical basis for the detection of PAHs content in asphalt materials, and support the development of low environmental hazard in construction technology for road engineering.

@en

This paper presents a discussion of “Study on Asphalt-Cement
Materials for Seismic Isolation Layer of Shield Tunnels” by Qi Yang,
Ping Geng, Liangjie Wang, Bingbing Zhao, and Pingliang Chen.
https://doi.org/10.1061/(ASCE)MT.1943-5533.0004466.@en

Crumb rubber modified bitumen (CRMB) can be regarded as a binary composite system in which swollen rubber particles are embedded in the bitumen matrix. Previous study has successfully implemented the micromechanics models in predicting the complex moduli of CRMB binders using more representative constituent parameters. In the regime of master curves, while the micromechanics models used predicted well in the high-frequency range, they underestimated the complex modulus in the low-frequency range. The current study aims to further improve the prediction accuracy of micromechanics models for CRMB by considering the interparticle interactions. To accomplish this goal, a new reinforcement mechanism called chain entanglement effect was introduced to account for the interparticle interaction effect. Results show that the polymer chain entanglement effect accounts for the underestimation of complex modulus and lack of elasticity (overestimation of phase angle) for CRMB at high temperatures/low frequencies. The mechanical properties of bitumen matrix and entangled polymer network can be determined based on the rubber content. The introduction of the entangled polymer network to the generalized self-consistent model significantly improved the prediction accuracy for both complex modulus and phase angle in the whole frequency range. In summary, by incorporating the physio-chemical interaction mechanism into the currently available models, a new dedicated micromechanics model for predicting the mechanical properties of CRMB has been developed. The predicted viscoelastic behaviors can thereafter be used as inputs for an improved mix design.@en

Low-temperature cracking is a major concern to improve the utilization of recycled asphalt mixture (RAM). A mechanism by which the crack propagates can provide a basis for advanced technological mitigation. Microcrack formations in the interfacial proximity of the virgin and aged binders have been identified from electron microscopy tests. Atomic force microscopy (AFM) experiment showed the trilayer phases at the virgin-aged binder interface. In this study, molecular dynamics (MD) simulations were conducted to understand the nanoscopic
crack propagation characteristics at the virgin-aged binder interface in the asphalt mixture with RAM. It was found that the blended binder of virgin and aged binders, and its interfaces with virgin and aged binders appeared to be the crack propagation zones. The relatively more significant matrix contraction of virgin binder and stiffer aged binder at a low temperature can cause more considerable tensile stress at the blended binder and its interfaces. Consequently, interfacial crack propagation became more profound and decreased the low temperature cracking resistance.@en

Considering the application scenarios of rubber granules from waste tires in the bitumen modification process (wet or dry process), both aerobic and anaerobic aging of rubber may occur. The current study aims to investigate the thermal aging behavior of waste tire rubber samples using nanoindentation and environment scanning electron microscopy (ESEM) tests. Both aerobic and anaerobic aging tests with different durations were conducted on rubber samples. The complex moduli of aged rubber samples were measured by nanoindentation tests. The surface morphology and elemental composition of aged samples were obtained by ESEM tests together with the energy dispersive X-ray analysis. Results have shown that for both aerobic and anaerobic aging, the equilibrium modulus derived from the complex modulus curve first increases and then decreases with aging time. However, the time needed for the aerobically aged sample to reach the maximum equilibrium modulus is shorter than the anaerobic case. Aging results in crack propagation and an increase of sulfur content on the rubber surface until it reaches the peak. The degree of crosslinking reflected by sulfur content for anaerobic aging is higher than aerobic aging. The morphological change and elemental change of rubber correlate well with the change of mechanical properties. The aging of rubber from the waste truck tire at 180°C can generally be separated into two stages: crosslinking dominant stage and chain scission dominant stage.@en

Rubberized asphaltic materials have been frequently combined with warm-mix asphalt technologies to tackle the issues of high energy consumptions and emissions during construction. Effective and accurate characterization of binder properties is conducive to the improvement of long-term pavement performance. The current study aims to quantify the effects of rubber content and warm-mix additives on rutting and thermal cracking performance of crumb rubber-modified bitumen (CRMB), and explore the rubber and additives modification mechanisms and their impacts on the binder performance. CRMBs containing different rubber contents and warm-mix additives after long-term aging were subject to multiple stress creep and recovery (MSCR) tests and low-temperature frequency sweep tests using a dynamic shear rheometer (DSR) with 4-mm loading plate to investigate the high- and low-temperature performance, respectively. Rheological tests were also conducted on the bitumen and rubber phases of CRMB to understand the rubber modification mechanism. Results show that CRMB binders have superior rutting and thermal cracking resistance due to rubber modification. The improvement of high- or low-temperature performance is more prominent at higher rubber concentrations. The effects of warm-mix additives on the rutting and thermal cracking performance are different. Generally, the wax-based additive improves the rutting resistance but negatively affects the low-temperature performance. In contrast, the chemical-based additive has an opposite effect except for the high-temperature performance of neat bitumen. The stiffening of the bitumen phase and the contribution of swollen rubber particles in the bitumen matrix together contribute to the peculiar viscoelastic response of CRMB, i.e., stiffer/softer and more elastic at high/low temperatures. This modification mechanism explains the superior rutting and thermal cracking performance of CRMB.

@en

Crumb rubber modified bitumen (CRMB) can be regarded as a binary composite system in which swollen rubber particles are embedded in the bitumen matrix. The current study aims to further improve the prediction accuracy of micromechanical models for CRMB by considering the interparticle interactions. To accomplish this goal, two different strategies were used. Firstly, the (n+1)-phase model was applied to the CRMB system by considering the multilayer properties of swollen rubber particles. Secondly, a new micromechanical scheme called the J-C model was used to account for the interparticle interaction issue. Results show that the (n+1)-phase models slightly increase the prediction accuracy but the underestimation of complex modulus at lower frequencies remains unsolved. The J-C model remedies the underestimation of modulus in the low-frequency range by other models and provides an overall improvement for the relative prediction accuracy by properly addressing the interparticle interactions from the perspective of particle configuration.

@en

From the pavement construction emission perspective, bitumen emulsion is considered more environment-friendly than conventional bitumen because of its much lower construction temperature. However, bitumen emulsion faces the major concern of low mechanical strength especially at high service temperatures. To improve the mechanical performance of bitumen emulsion, waterborne epoxy resin can be used as a modifier. Nevertheless, there still lacks fundamental understanding on the effects of waterborne epoxy resin on the microstructure and rheological performances of the residual bitumen of the emulsion. To fill this gap, this study aims to investigate the microstructure and develop the constitutive model of the waterborne epoxy resin-modified bitumen emulsion residue (WEBER). To achieve this objective, a confocal laser scanning microscopy was first adopted to characterise the microstructure of WEBER. The frequency sweep tests were then conducted, and the ‘2S2P1D’ model was applied to simulate the WEBER’s dynamic response at different loading frequencies. The results indicated that the waterborne epoxy resin formed a polymer-rich film around the bitumen phase in the emulsion residue when its content reached 3 wt%, and the ‘2S2P1D’ model can well describe the WEBER’s dynamic response at different loading frequencies.

@en

Permeable pavements are often affected by pore clogging, which leads to their functional failure and reduced service life. However, the clogging mechanism and its impact on the permeability and complex pore microstructures in pervious pavement remains unclear. The aim of current study is to quantify the clogging behavior in pervious pavement materials and carry out investigations on the development of pore characteristics and permeability. Novel Polyurethane bound pervious mixture (PUPM) were adopted for comparative study in present research with conventional Porous Asphalt (PA). The Aachen Polishing Machine (APM) was selected to perfectly serve as a simulator for clogging process of pavement in the actual service condition. The development of pore characteristics in terms of clogging was experimentally illustrated. The developed experiments and analysis can further strengthen the understanding of the clogging mechanism within the porous pavement material.@en