The vertical axis wind turbine (VAWT) concept in its current, fixed-pitch iteration is hindered by lower aerodynamic efficiency compared to existing horizontal axis wind turbines. Implementing a form of circulation control on the VAWT by actively pitching the blades throughout the turbine’s rotation could potentially enhance power capture efficiency and reduce loads variability. In this thesis, circulation control is investigated in 3D, since the 3D flow field differs significantly from the 2D equivalent.After a review of available 2D and 3D aerodynamic models for the VAWT, a suitable candidate emerges in the form of HAWC2 NW, which is a lifting-line based extension to popular aeroelastic modelling suite HAWC2 designed to model trailed vorticity in the near wake of the blade. HAWC2 NW is used to conduct fast 3D aerodynamic simulations of a highly simplified vertical axis wind turbine geometry to demonstrate the influence of 3D effects on the flow field surrounding the VAWT. The slenderness of the turbine geometry, expressed using the turbine aspect ratio H/D, turns out to be a major factor in determining the performance losses due to 3D effects.Subsequently, HAWC2 NW is used to analyze optimized pitch sequences with various objectives, such as maximum power or a certain normal loading distribution. A relationship is found between the ratio of upwind and downwind normal loading, the turbine aspect ratio H/D and the 3D power coefficient CP,3D. The most important conclusion is that when considering the design of a vertical axis wind turbine with a turbine aspect ratio H/D < 5, losses due to 3D effects can be minimized by implementing a circulation control strategy in such a way that the normal loading is uniformly distributed between the upwind and downwind half-cycles.

Multiple concepts for hybrid vehicles capable of both road and flight transport are becoming a reality. However, through incorporation of both flight and road hardware into one vehicle these designs become inefficient. The aim of this project is to design an alternative strategy for realising optimised hybrid vehicles. The objective of this project is to "Develop a personal transport vehicle suitable for commuter use on which flight hardware can be attached within 5 minutes, by 10 students within 10 weeks". This was derived from the mission statement which was to "Develop a faster and cheaper personal transport vehicle for the European market with detachable flight/road hardware that combines the advantages of road transport with flight capability". From this objective, the three most key requirements are that the vehicle shall have a road and flight configuration, that the flight hardware shall be separable from the road hardware and that the flight hardware shall be attached/detached from the road hardware within 5 minutes. When analysing the performance of the vehicle, typical flight stages and stalling configurations were investigated in terms of speed and power setting. At cruise speed, the 12 DEP (Distributed Electric Propulsion) propellers in the midsection of the wing are turned off and folded . However, for take-off and landing configuration, all the propellers are switched on. For fuel use two options are present. E10 gasoline for maximum range, or E85 for decent range, but a 70% lower eco-impact. 122 kW of power is supplied to the 6 outboard motors during cruise. The take-off distance is 450 m and the landing distance is 462 m. Two different propellers were designed and optimized for DEP and cruise conditions. To verify the noise requirements, a propeller noise analysis of the vehicle was carried out, since that is the largest contributer to overall vehicle noise. From that analysis it was concluded that the propeller noise level of the vehicle is 52.3 dBA at 1000 ft, which is low compared to other general aviation aircraft. The airfoil of the wing was selected using the design lift coefficient of 0.56. The airfoils chosen for the wing and tail are, respectively, theNACA4418 andNACA0012. Thewingwas designed to have an aspect ratio of 17, a surface area of 8.414 m2 and a span of 11.96 m. Using these values, the induced drag and pitching moment coefficients were determined. To investigate the overall efficiency of the aerodynamics of the wing, the lift over drag ratio (L/D) was calculated for each configuration. For cruise, landing and take-off, the L/D is 12.93, 7.74 and 9.48, respectively. The packaging of the vehicle resulted in the centre of gravity of the operative empty weight of the full configuration to act at 37.4% of the fuselage length at an empty mass of 1174.7 kg. The longitudinal and lateral stability and control of the vehicle were assessed. Due to the large downwash caused by the DEP propellers of the wing, a T-tail configuration was designed to move the tail away from the downwash and make it more effective. A fully-movable horizontal tail was necessary to counter the large lift coefficient and, consequently, the moment created by distributed electrical propulsion. The horizontal and vertical stabiliser were designed with a surface area of 2.42m2 and 1.1m2 respectively. After analysing the strengths and manufacturing methods of several materials it was found that the wingbox would be made using aluminium (AL7075-T6) with taper in the sheet thickness. Due to the slender wing, the weight of the wing became relatively high at 200 kg. For the skin, the most suitable material was polyester with glass fibres for its specific strength, price and compatibility with a foam or balsa core. For the linkage system, the location where the linkage is established needed to be considered. After investigating this, it was determined that the best place for the linkage would be the rear of the road hardware and the front of the flight hardware. For the linkage the Scharfenberg train coupling was used together with safety pins. The Scharfenberg connection was scaled down to suit the vehicle as it was originally designed for trains. After the final design is concluded, it is necessary to plan for future research in order to make this concept a reality. There are still uncertainties in how DEP affects the performance and aerodynamics of the concept. Therefore, it is recommended to conduct more lowspeed tests to properly establish those effects. Computational FluidDynamics (CFD) and wing tunnel testing is also recommended to visualise and analyse the fluid flow of the wing. A structural analysis using the finite elementmethod and full scale tests of themajor components are also recommended. As the coupling mechanism has never been used in aerospace application, further research into the adaptability and the integration of this mechanism should be performed. As a single-engine Private Pilot License is preferred, recommendations were also made on tests that need to be performed in order to make a case for the airworthiness authorities.