Compact and efficient power converter solutions are seen to be the backbone of future transportation systems in order to cope with the ongoing transition toward greener systems. Such systems usually comprise a main load section, in which one or more propulsion or traction motors are connected, in addition to an auxiliary load, which might comprise the hotels and air conditioning for example. This auxiliary load can be as low as 5-10% of the main load power. Therefore, it can be challenging to drive this power from a typical high-power system that employs a medium-voltage (MV) dc (MVDC) grid, which is typical in high-power systems. In such MVDC-integrated systems, neutral-point-clamped and active neutral-point-clamped (ANPC) converters are commonly used, where the auxiliary load converter is overrated in this case, resulting in a bulky and inefficient power system. Thus, in order to enable a lighter and efficient transportation power system, a multiport hybrid converter (MHC) is presented in this article. This converter can feed the main MV motor, in addition to two auxiliary low-voltage loads. Compared with the state-of-the-art ANPC converter, the proposed MHC utilizes only two extra switches per phase leg in order to achieve this multiport operation along with increasing the voltage rating of another two switches. The proposed MHC is analyzed in this article, where its operation, modulation, and mathematical derivation are presented. These analyses are supported by simulation and experimental results utilizing a reduced-scale 5-kW system.

This work proposes a hybrid space vector modulation (HSVM) scheme for multiport hybrid converters (MHCs). Moreover, the impact of shifting the auxiliary currents from the main ones is proposed and investigated in order to enhance the converter efficiency. The proposed operational schemes have been implemented in a three-phase 5 kW MHC prototype. It is shown that the proposed HSVM scheme can improve the MHC efficiency by 0.3% at full load with respect to space vector modulation. At partial loads, the improvement is even more significant, reaching +0.7% at 30% of the rated power. A further 0.15% increase in efficiency at full power can be achieved by a 180$^{\circ }$ phase shifting of the auxiliary currents with respect to the main terminal currents, reaching a peak efficiency of 98.5%.

This article discusses the application of battery energy storage systems (BESSs) as power redistributors in three-phase distribution grids as an add-on functionality to typical BESS applications, such as congestion management and energy arbitrage. Combining those ancillary services into a single power unit is not yet performed in practice but may constitute an emerging business opportunity to increase the BESS revenues. The unbalanced operation of the BESS voltage source converter (VSC) leads to the circulation of low-frequency current harmonics in the dc-link through the capacitors and the battery cells. Therefore, it is particularly interesting whether relatively large 50- and 100-Hz currents can safely circulate within these components. Analytical modeling and design guidelines for the dc-link of a three-leg four-wire two-level VSC operating under unbalanced loads are detailed. Furthermore, a low-power VSC prototype is used to demonstrate the working principle of the BESS, providing power unbalance redistribution and symmetric power exchange. Additionally, the ICR18650-26F Lithium-ion cells are cycled to reach end-of-life with different current profiles and C-ratings. The analysis shows that charging with a 100 Hz ripple superimposed to the dc current leads to a 10% increment in degradation.

In this article, a hybrid Si/Si carbide (SiC) switch (HyS) modulation with minimum SiC MOSFET conduction (mcHyS) is experimentally characterized, so as to derive its conduction and switching performance. These are later used to derive a silicon (Si) area analytical model for the HyS configuration. The chip area model is used to benchmark the mcHyS modulation concepts against single-technology switches and typical HyS modulation when considering the implementation of a 100-kW two-level voltage-source converter (VSC) deployed for three industrial applications: photovoltaic inverter, electric vehicle fast-charging station, and battery storage systems for grid ancillary service. The two additional switching events of the SiC MOSFET, which differentiate the mcHyS modulation from the typical HyS one, are proven to happen in soft switching; therefore, the mcHyS switching performances are not penalized. Furthermore, the analysis presented shows how the studied mcHyS modulation performs against the single semiconductor technology and the typical HyS solution in terms of cost and power conversion efficiency. More specifically, it is shown that the HyS solutions are particularly competitive versus the full Si-based VSCs when the application at hand often operates at low partial loads. Finally, a 10-kW two-level VSC assembled with mcHyS is tested, so as to compare its efficiency versus single-technology switches.

Variable switching frequency PWM (VSFPWM) modulation can be advantageously implemented in industrial applications, such as renewable energy, motor drives, and uninterrupted power supply (UPS) systems, to reduce the injected current harmonic amplitudes, to suppress audible noise, and to improve semiconductor power efficiency. In this article, the usage of periodic VSFPWM methods in a voltage source converter (VSC) is proposed, analyzed, and benchmarked in terms of harmonic spectrum spreading, following the IEEE-519 current harmonic standard for the connection to the distribution grid. Particular attention is paid to the influence of VSFPWM on the ac filter design. First, the analytical model of the voltage harmonic spectrum generated by a three-phase three-wire two-level VSC implementing several periodic VSFPWM methods is derived. Subsequently, a design guideline for the commonly used LCL filter in the grid-tied VSC application is proposed, which minimizes the size requirement of the necessary components. The voltage spectrum models of the proposed VSFPWM method and the optimal switching profiles are verified by MATLAB/Simulink simulations and a 5-kW three-phase two-level VSC hardware demonstrator. The study shows that the ac filter power density for the studied VSFPWM methods can be greatly increased when compared with the conventional and widely employed constant switching frequency continuous PWM strategies.

This paper discusses a qualitative comparison between Two and Three-Level Voltage Source Converter (VSC) topologies for battery energy storage applications. Three-Level Neutral Point Clamped (NPC) and T-Type circuit topologies are benchmarked versus the state-of-art Two-Level VSC in terms of efficiency and power density considering a 100 kW system. Analytical equations for determining the power losses in the semiconductor modules are given, and the procedure for designing the output LCL filter and the DC-link capacitors is described. The analysis, based on off-the-shelf circuit components, shows that the Three-Level topologies perform better than the Two-Level one in both considered metrics, mainly due to their lower switching losses that allow operating at higher switching frequency without significantly degrading the system efficiency, and, at the same time, increasing the system power density. Additionally, it is found that the T-Type topology shows better performances than the NPC topology at full and high partial loads, being then more suitable for applications that require most of the operation at maximum power.