Parallel-plate capacitors (PPC) significantly reduce the size of superconducting microwave resonators, reducing the pixel pitch for arrays of single-photon energy-resolving kinetic inductance detectors (KIDs). The frequency noise of KIDs is typically limited by tunneling two-level systems (TLS), which originate from lattice defects in the dielectric materials required for PPCs. How the frequency noise level depends on the PPC's dimensions has not been experimentally addressed. We measure the frequency noise of 56 resonators with a-SiC:H PPCs, which cover a factor of 44 in PPC area and a factor of 4 in dielectric thickness. To support the noise analysis, we measure the resonators' TLS-induced power-dependent intrinsic loss and temperature-dependent resonance frequency shift. From the TLS models, we expect a geometry-independent microwave loss and resonance frequency shift, which is set by the TLS properties of the dielectric. However, we observe a thickness-dependent microwave loss and resonance frequency shift; this is explained by surface layers that limit the performance of PPC-based resonators. For a uniform dielectric, the frequency noise level should scale directly inversely with the PPC area and thickness. We observe that an increase in PPC size reduces the frequency noise, but the exact scaling is, in some cases, weaker than expected. Finally, we derive engineering guidelines for the design of KIDs based on PPC-based resonators.

Kinetic inductance detectors (KIDs) are superconducting energy-resolving detectors, sensitive to single photons from the near-infrared to ultraviolet. We study a hybrid KID design consisting of a β-phase tantalum (β-Ta) inductor and a Nb-Ti-N interdigitated capacitor. The devices show an average intrinsic quality factor Qi of 4.3×105±1.3×105. To increase the power captured by the light-sensitive inductor, we 3D print an array of 150×150μm resin microlenses on the backside of the sapphire substrate. The shape deviation between design and printed lenses is smaller than 1μm, and the alignment accuracy of this process is δx=+5.8±0.5μm and δy=+8.3±3.3μm. We measure a resolving power for 1545-402 nm that is limited to 4.9 by saturation in the KID's phase response. We can model the saturation in the phase response with the evolution of the number of quasiparticles generated by a photon event. An alternative coordinate system that has a linear response raises the resolving power to 5.9 at 402 nm. We verify the measured resolving power with a two-line measurement using a laser source and a monochromator. We discuss several improvements that can be made to the devices on a route towards KID arrays with high resolving powers.

A noiseless, photon-counting detector, which resolves the energy of each photon, could radically change astronomy, biophysics, and quantum optics. Superconducting detectors promise an intrinsic resolving power at visible wavelengths of R=E/δE≈100 due to their low excitation energy. We study superconducting energy-resolving microwave kinetic inductance detectors (MKIDs), which hold particular promise for larger cameras. A visible and near-infrared photon absorbed in the superconductor creates a few thousand quasiparticles through several stages of electron-phonon interaction. Here we demonstrate experimentally that the resolving power of MKIDs at visible to near-infrared wavelengths is limited by the loss of hot phonons during this process. We measure the resolving power of our aluminum-based detector as a function of photon energy using four lasers with wavelengths between 1545-402nm. For detectors on thick SiN/Si and sapphire substrates the resolving power is limited to 10-21 for the respective wavelengths, consistent with the loss of hot phonons. When we suspend the sensitive part of the detector on a 110-nm-thick SiN membrane, the measured resolving power improves to 19-52, respectively. The improvement is equivalent to a factor 8±2 stronger phonon trapping on the membrane, which is consistent with a geometrical phonon propagation model for these hot phonons. We discuss a route towards the Fano limit by phonon engineering.