This technical note presents a simplified method for quantifying the added mass of the soil that is mobilised as part of the failure mechanism around a foundation during rapid loading, and the resulting additional soil resistance. This note focuses on the solutions for an embedded plate anchor, which is a potential foundation system for offshore floating facilities. In current practice, only the shear strength of the soil surrounding the foundation is considered in calculations of the ultimate bearing capacity. However, the solutions presented in this technical note show that the added mass of the soil involved in the failure mechanism around the foundation can result in a significant increase in ultimate bearing capacity during extreme dynamic wave loading events. These lead to snatch loads transmitted to the anchoring and mooring system, which are high but brief. The technical note provides a general approach applicable to all foundation types, and illustrates the effect of the added mass term and the additional capacity for an embedded plate anchor with typical input conditions.

In recent years, fibre Bragg grating (FBG) sensors have emerged as a relatively new strain sensing technology for civil engineering applications. This paper presents a field trial to assess the feasibility of using FBG sensor arrays to measure strain in driven steel piles. Two FBG arrays were installed in grooves within the wall of an open-ended steel pile such that the finished profile was completely flush with the pile shaft. The pile was then driven into a dense sand deposit using an impact hammer to provide the required installation energy. The FBG gauges were monitored throughout driving in conjunction with accelerometers to quantify the scale of the hammer impacts. The FBG sensors were subjected to hammer blows that yielded pile accelerations between 500 g and 1400 g during installation. The fibre optic sensors were measured throughout driving, where they were observed to respond to the hammer impacts, showing a rapid increase in strain and a return to their initial values between hammer strikes. After installation, a lateral load test was performed with independent load measuring devices. Excellent agreement was observed between the measured moments and those inferred from the FBG strain output. The output of this trial demonstrates that FBG strain sensors are a viable means of measuring load transfer in foundation systems and are suitably robust to withstand high pile driving accelerations.

Offshore wind turbines are typically founded on single large diameter piles, termed monopiles. Pile diameters of between 5mand 6mare routinely used, with diameters of up to 10 m, or more, being considered for future designs. There are concerns that current design approaches, such as the p − y method, which were developed for piles with a relatively large length to diameter ratio, may not be appropriate for large diameter monopiles. A joint industry project, PISA (PIle Soil Analysis), has been established to develop new design methods for large diameter monopiles under lateral loading. The project involves three strands of work; (i) numerical modelling; (ii) development of a new design method; (iii) field testing. This paper describes the framework on which the new design method is based. Analyses conducted using the new design method are compared with methods used in current practice.

There is currently a significant focus on developing offshore wind power in the UK and Europe. The most common foundation type for wind turbines is a single large diameter pile, termed a monopile, on which the turbine is located. As the diameter of such piles is envisaged to increase in future installations, there are concerns that current design methods are not applicable. To explore this problem, the joint industry project PISA has been established, with the aim to develop a new design framework for laterally loaded piles utilised in the offshore wind industry, based on new theoretical developments, numerical modelling and large scale field pile testing. This paper presents an overview of numerical modelling undertaken as part of the project.

Offshore wind power in the UK, and around Europe, has the potential to deliver significant quantities of renewable energy. The foundation is a critical element in the design. The most common foundation design is a single large diameter pile, termed a monopile. Pile diameters of between 5m and 6m are routinely used, with diameters up to 10m or more, being considered for future designs. Questions have been raised as to whether current design methods for lateral loading are relevant to these very large diameter piles. To explore this problem a joint industry project, PISA, co-ordinated by DONG Energy and the Carbon Trust, has been established. The aim of the project is to develop a new design framework for laterally loaded piles based on new theoretical developments, numerical modelling and bench- marked against a suite of large scale field pile tests. The project began in August 2013 and is scheduled to complete during 2015. This paper briefly outlines the project, focusing on the design of the field testing. The testing involves three sizes of pile, from 0.27m in diameter through to 2.0m in diameter. Two sites will be used; a stiff clay site and a dense sand site. Tests will include monotonic loading and cyclic loading. A suite of site investigation will be carried out to aid interpretation of the field tests, and will involve in-situ testing, standard laboratory testing and more advanced laboratory testing.