When solid-state redox-driven phase transformations are associated with mass loss, vacancies are produced that develop into pores. These pores can influence the kinetics of certain redox and phase transformation steps. We investigated the structural and chemical mechanisms in and at pores in a combined experimental-theoretical study, using the reduction of iron oxide by hydrogen as a model system. The redox product (water) accumulates inside the pores and shifts the local equilibrium at the already reduced material back toward reoxidation into cubic Fe1-xO (where x refers to Fe deficiency, space group Fm3¯m). This effect helps us to understand the sluggish reduction of cubic Fe1-xO by hydrogen, a key process for future sustainable steelmaking.

Tungsten stands a prime candidate for plasma-facing applications in fusion reactors, attributed to its capacity to withstand high temperatures and intensive particle fluxes. The operational heat flux, however, can induce recrystallisation of the initial microstructure, increasing the brittle-to-ductile transition temperature. Although such a phenomenon is thought to result from impurity segregation to grain boundaries, direct evidence of impurity-induced grain boundary embrittlement has not yet been reported. Addressing this, our study employs microcantilever testing, coupled with local chemical analysis via atom probe tomography, to unveil the impact of impurity segregation on the fracture toughness of recrystallised tungsten with a purity of 99.98 at.%. The in situ fracture toughness measurements were performed with the notch placed directly at random high-angle grain boundaries, revealing brittle failure regardless of grain boundary misorientation or grain orientation. Notably, both single-crystalline microcantilevers and the as-received material exhibited significant plasticity before failure, with instances without crack propagation. In contrast, recrystallised grain boundaries displayed a fracture toughness of 4.7 ± 0.4 MPa·√m, determined using a linear elastic approach - notably lower than for cleavage plane fracture in tungsten microcantilevers. Local atom probe analysis of the high-angle grain boundaries exposed phosphorous segregation exceeding 2 at.% at the recrystallised interfaces, stemming from recrystallisation. Atomistic simulations confirmed the role of phosphorous in embrittling high-angle grain boundaries in tungsten, while additionally revealing mechanisms of crack-grain boundary interactions and their dependence on phosphorous segregation.

In conventional metallic materials, strength and ductility are mutually exclusive, referred to as strength-ductility trade-off. Here, we demonstrate an approach to improve the strength and ductility simultaneously by introducing micro-banding and the accumulation of a high density of dislocations in single-phase high-entropy alloys (HEAs). We prepare two compositions (Cr₁₀Mn₅₀Fe₂₀Co₁₀Ni₁₀ and Cr₁₀Mn₁₀Fe₆₀Co₁₀Ni₁₀) with distinctive different stacking fault energies (SFEs) as experimental materials. The strength and ductility of the Cr₁₀Mn₅₀Fe₂₀Co₁₀Ni₁₀ HEA are improved concurrently by grain refinement from 347.5 ± 216.1 µm to 18.3 ± 9.3 µm. The ultimate tensile strength increases from 543 ± 4 MPa to 621 ± 8 MPa and the elongation to failure enhances from 43±2% to 55±1%. To reveal the underlying deformation mechanisms responsible for such a strength-ductility synergy, the microstructural evolution upon loading is investigated by electron microscopy techniques. The dominant deformation mechanism observed for the Cr₁₀Mn₅₀Fe₂₀Co₁₀Ni₁₀ HEA is the activation of micro-bands, which act both as dislocation sources and dislocation barriers, eventually, leading to the formation of dislocation cell structures. By decreasing grain size, much finer dislocation cell structures develop, which are responsible for the improvement in work hardening rate at higher strains (>7%) and thus for the increase in both strength and ductility. In order to drive guidelines for designing advanced HEAs by tailoring their SFE and grain size, we compute the SFEs of Cr₁₀Mn_xFe_70–xCo₁₀Ni10 (10 ≤ x ≤ 60) based on first principles calculations. Based on these results the overall changes on deformation mechanism can be explained by the influence of Mn on the SFE.