A 40-nm CMOS wakeup timer employing a bang-bang digital-intensive frequency-locked loop for Internet-of-Things applications is presented. A self-biased ΣΔ digitally controlled oscillator (DCO) is locked to an RC time constant via a single-bit chopped comparator and a digital loop filter. Such highly digitized architecture fully exploits the advantages of advanced CMOS processes, thus enabling operation down to 0.7 V and a small area (0.07 mm 2 ). Most circuitry operates at 32× lower frequency than the DCO in order to reduce the total power consumption down to 181 nW. High frequency accuracy and a 10× enhancement of long-term stability is achieved by the adoption of chopping to reduce the effect of comparator offset and 1/f noise and by the use of ΣΔ modulation to improve the DCO resolution. The proposed timer achieves the best energy efficiency (0.43 pJ/cycle at 417 kHz) over prior art while keeping excellent on-par long-term stability (Allan deviation floor <;20 ppm) and temperature stability (106 ppm/°C).@en

This paper presents a 1.8-2.7 GHz low-power ring-oscillator-based fractional-N injection-locked digital PLL (IL-DPLL) in 40-nm CMOS for Internet-of-Things clock generation. A two-path injection technique is proposed to improve the in-band phase noise and the integrated jitter of the implemented PLL by 6 dB and 1.8×, respectively. Furthermore, a digital foreground calibration is introduced to effectively reduce reference spurs in a short calibration time of 2 μs. In the worst-case channel, the proposed DPLL using a 64 MHz reference input shows a 1.6 ps integrated jitter, -43.6 dBc reference spur, -45.8 dBc fractional spur and 1 kHz frequency resolution while consuming 1.33 mW power.

@en

This paper presents the system and circuit design of a compact radio frequency (RF)-powered 2.4-GHz CMOS transmitter (TX) to be used for autonomous wireless sensor nodes (WSNs). The proposed TX utilizes the received dedicated RF signal for both energy harvesting as well as frequency synthesis. A TX RF carrier is derived from the received RF signal by means of a delay locked loop and XOR-based frequency multiplier. The 50-Ω load is subsequently driven by a tuned switching RF power amplifier (PA) with 25% duty cycle input for high global efficiency. The design is fabricated in 40-nm CMOS technology and occupies a die area of 0.16 mm2. Experimental results show a rectifier with 36.83% peak efficiency and power management circuit with 120-nA current consumption that enables a low start-up power of -18.4 dBm. The TX outputs a continuous 2.44-GHz RF signal at -2.57 dBm with 36.5% PA drain efficiency and 23.9% global efficiency from a 915-MHz RF input and supports ON-OFF keying modulation.@en

This paper introduces an ultra-low power 1.7-2.7-GHz fractional-N sub-sampling digital PLL (SS-DPLL) for Internet-of-Things (IoT) applications targeting compliance with Bluetooth Low Energy (BLE) and IEEE802.15.4 standards. A snapshot time-to-digital converter (TDC) acts as a digital sub-sampler featuring an increased out-of-range gain and without any assistance from the traditional counting of DCO edges, thus further reducing power consumption. With a proposed DCO-divider phase rotation in the feedback path, the impact of the digital-to-time converter's (DTC's) non-linearity on the PLL is reduced and improves fractional spurs by at least 8 dB across BLE channels. Moreover, a “variable-preconditioned LMS” calibration algorithm is introduced to dynamically correct the DTC gain error with fractional frequency control word (FCW) down to 1/16384. Fabricated in 40 nm CMOS, the SS-DPLL achieves phase noise performance of -109 dBc/Hz at 1 MHz offset, while consuming a record-low power of 1.19 mW.@en

We propose an ultra-low-power (ULP) and low-voltage phase-tracking RX for IoT applications. Several popular standards are defined for IoT, e.g., IEEE802.15.4 and Bluetooth Low Energy (BLE), where they envision massive numbers of interconnected sensors; however, the cost of replacing/recharging batteries can become an impediment to their massive deployment. In this work, aggressively improving the transceiver energy efficiency, lowering the supply, and simultaneously reducing the cost (die area) of the design are our primary goals. Hence, we propose a digitally-controlled oscillator (DCO)-based phase-tracking RX, which efficiently combines frequency downconversion, channel selection, carrier generation and signal demodulation, all of which lead to an ultra-low-power, low-voltage and low-cost RX.

@en