The present paper reports on a field experiment performed over a shallow, roughness-varying barrier reef at Maupiti island, French Polynesia. The spectral wave energy balance is examined, outside the breaking zone and accounting for non-linear transfers and mean current, to estimate the wave friction factor. This latter varies from 0.05 to 4, with dependence on the ratio between near-bed orbital amplitude and roughness height well predicted by an adjusted parameterization from Madsen (1995). The present results are discussed with respect to other field data recovered on coral and rocky grounds.

@en

Dynamic cobble berm revetments are a promising soft engineering technique capable of protecting sandy coastlines by armouring the sand and dissipating wave energy to protect the hinterland against wave attack. They also form composite beaches as they are essentially mimicking natural composite beach structure and behaviour. This type of coastal protections and beaches have recently been investigated, and this led to a better understanding of their overall behaviour under varying water levels and wave conditions. However, the short-term dynamics of the swash zone (where all bed changes occur) has never been studied at high-resolution, and this is needed to fully understand the underlying dynamics of such structures and relate it to observed processes at larger scale. To do so, the revetment at North Cove (WA, USA) was monitored for a nine-day period in January 2019 over a spring tidal cycle and with offshore significant wave height reaching 6 m. A 2-D lidar was used to survey a cross-shore profile of the revetment, and record all surface changes and interaction with swashes at high spatial (0.1 m) and temporal (swash-by-swash) resolution. The revetment was found to rapidly reshape under these energetic conditions, but reached a relatively stable state during the rising tide. The analysis of bed-level changes and net cross-shore mass fluxes over the revetment showed that revetment changes are mainly driven by very small events, with some rare large bed-level changes of a magnitude comparable to the median cobble diameter. The distribution of event mass fluxes nearly balanced out over the duration of a tide, meaning that positive and negative fluxes tended to be symmetrical. Furthermore, measured net fluxes magnitude were 18 times smaller than the absolute fluxes, which demonstrated the dynamic stability of the revetment as substantial movement occur on a wave-by-wave timescale but these balance out over time. The analysis of swash revealed that the revetment section where the swash reaches a maximum depth between 0.15 and 0.45 m undergoes the more extreme fluxes. Swashes deeper than 0.45 m only occurred in zones inundated more than 50% of the time, and smaller extreme fluxes were measured over the revetment section where these deep swashes were recorded. Bed level change oscillations over the revetment were observed, and the cross shore limit of these was correlated with the mean wave period at the toe of the revetment. Overall, the water depth at the toe of the revetment was identified as the key parameter to describe the energy reaching the revetment. This study enables the morphodynamics of dynamic revetment, observed in previous lab and field studies, to be explained at the swash scale, and brought new information on the sediment dynamics of composite beaches and dynamic revetments. These findings allow to suggest some generic guidance for dynamic cobble berm revetment design. Finally, the results are compared to a similar study on sandy beaches.@en

Pressure on the coastline is escalating due to the impacts of climate change, this is leading to a rise in sea-levels and intensifying storminess. Consequently, many regions of the coast are at increased risk of erosion and flooding. Therefore coastal protection schemes will increase in cost and scale. In response there is a growing use of nature-based coastal protection which aim to be sustainable, effective and adaptable. An example of a nature-based solution is a dynamic cobble berm revetment: a berm constructed from cobble and other gravel sediments at the high tide wave runup limit. These structures limit wave excursion protecting the hinterland from inundation, stabilise the upper beach and adapt to changes in water level. Recent experiments and field applications have shown the suitability of these structures for coastal protection, however many of the processes and design considerations are poorly understood. This study directly compares two prototype scale laboratory experiments which tested dynamic cobble berm revetments constructed with approximately the same geometry but differing gravel characteristics; well-sorted rounded gravel (DynaRev1) and poorly-sorted angular gravel (DynaRev2). In both cases the structures were tested using identical wave forcing including incrementally increasing water level and erosive wave conditions. The results presented in this paper demonstrate that both designs responded to changing water level and wave conditions by approaching a dynamically stable state, where individual gravel is mobilised under wave action but the geometry remains approximately constant. Further, both structures acted to reduce swash excursions compared to a pure sand beach. However, their morphological behaviour is response to wave action varied considerably. Once overtopping of the designed crest occurred, the poorly-sorted revetment developed a peaked crest which grew in elevation as the water level or wave height increased, further limited overtopping. By comparison, the well-sorted revetment was characterised by a larger volume of submerged gravel and a lower elevation flat crest which responded less well to changes in conditions. This occurred due to two processes: (1) for the poorly-sorted case, gravel sorting processes moved small to medium gravel material (D₅₀<70mm) to the crest and (2) the angular nature of the poorly-sorted gravel material promoted increased interlocking. Both of these processes led to a gravel matrix that is more resistant to wave action and gravitational effects. Both revetments experienced some sinking due to sand erosion beneath the front slope. The rate of sinking for the well-sorted case was larger and continued throughout due to the large pore spaces within the gravel matrix. For the poorly sorted revetment in DynaRev2, sand erosion ceased after approximately 28 h due to the development of a filter layer of small gravel at the sand-gravel interface reducing porosity at this location, hence a larger volume of sand was preserved beneath the structure. Both designs present a low-cost and effective solution for protecting sandy coastlines but from an engineering viewpoint it appears better to avoid well-sorted gravel material and greater gravel angularity has been seen to increase crest stability.

@en

The effects of climate change and sea level rise, combined with overpopulation are leading to ever-increasing stress on coastal regions throughout the world. As a result, there is increased interest in sustainable and adaptable methods of coastal protection. Dynamic cobble berm revetments consist of a gravel berm installed close to the high tide shoreline on a sand beach and are designed to mimic naturally occurring composite beaches (dissipative sandy beaches with a gravel berm around the high tide shoreline). Existing approaches to predict wave runup on sand or pure gravel beaches have very poor skill for composite beaches and this restricts the ability of coastal engineers to assess flood risks at existing sites or design new protection structures. This paper presents high-resolution measurements of wave runup from five field and large-scale laboratory experiments investigating composite beaches and dynamic cobble berm revetments. These data demonstrated that as the swash zone transitions from the fronting sand beach to the gravel berm, the short-wave component of significant swash height rapidly increases and can dominate over the infragravity component. When the berm toe is submerged at high tide, it was found that wave runup is strongly controlled by the water depth at the toe of the gravel berm. This is due to the decoupling of the significant wave height at the berm toe from the offshore wave conditions due to the dissipative nature of the fronting sand beach. This insight, combined with new methods to predict wave setup and infragravity wave dissipation on composite beaches is used to develop the first composite beach/dynamic revetment-specific methodologies for predicting wave runup.@en

Martins, K.; Bonneton, P.; Bayle, P.M.; Blenkinsopp, C.E.; Mouragues, A., and Michallet, H., 2020. Surf zone wave measurements from lidar scanners: Analysis of non-hydrostatic processes. In: Malvárez, G. and Navas, F. (eds.), Global Coastal Issues of 2020. Journal of Coastal Research, Special Issue No. 95, pp. 1189-1194. Coconut Creek (Florida), ISSN 0749-0208. Lidar scanners provide the ability to directly measure the free surface of breaking waves, however it is generally necessary to mount the scanners above the water surface on a nearshore structure such as a jetty. Pressure sensors on the other hand are easy to deploy and remain the simplest alternative to collect field measurements of surf zone waves, the free surface being generally reconstructed from the linear transfer function. Recent studies have highlighted the limitations of this traditional approach to describe geometric properties of nonlinear waves. In the surf zone, this issue remains largely overlooked, principally due to the absence of direct measurements of the free surface elevation. The present contribution addresses this gap by using data collected by collocated sub-surface pressure sensors and lidar during the DynaRev set of experiments, which were performed at the prototype scale. During these experiments, a 1:15 sandy beach was exposed to irregular waves for 20 hours, and reached a quasi-equilibrium state at the end of the test phase, exhibiting a bar-terrace profile. In the inner surf zone, errors between 10% and 40% are obtained on second and third-order wave parameters with the classic transfer function based on linear wave theory. Only a recently developed non-linear weakly dispersive reconstruction method is found to be capable of describing wave-by-wave parameters and thus the root-mean square wave height Hrms in the surf zone. This has important implications for the estimation of wave height distributions based on pressure data, which are illustrated here, and calls for a reanalysis of old datasets and reconsideration of hypotheses based on pressure transducer datasets.

@en