Ocean-bottom seismometers (OBSs) are equipped with seismic sensors that record acoustic and seismic events at the seafloor, which makes them suitable for investigating tectonic structures capable of generating earthquakes offshore. One critical parameter to obtain accurate earthquake locations is the absolute time of the incoming seismic signals recorded by the OBSs. It is, however, not possible to synchronize the internal clocks of the OBSs with a known reference time, given that GNSS signals are unable to reach the instrument at the sea bottom. To address this issue, here we introduce a new method to synchronize the clocks of large-scale OBS deployments. Our approach relies on the theoretical time-symmetry of time-lapse (averaged) crosscorrelations of ambient seismic noise. Deviations from symmetry are attributed to clock errors. This implies that the recovered clock errors will be obscured by lapse crosscorrelations' deviations from symmetry that are not due to clock errors. Non-uniform surface wave illumination patterns are arguably the most notable source which breaks the time symmetry. Using field data, we demonstrate that the adverse effects of non-uniform illumination patterns on the recovered clock errors can be mitigated by means of a weighted least-squares inversion that is based on station-station distances. In addition, our methodology permits the recovery of timing errors at the time of deployment of the OBSs. This error can be attributed to either: i) a wrong initial time synchronization of the OBS or ii) a timing error induced by changing temperature and pressure conditions while the OBS is sunk to the ocean floor. The methodology is implemented in an open-source Python package named OCloC, and we applied it to the OBS recordings acquired in the context of the IMAGE project in and around Reykjanes, Iceland. As expected, most OBSs suffered from clock drift. Surprisingly, we found incurred timing errors at the time of deployment for most of the OBSs.@en

The timing of the recordings of ocean-bottom seismometers (OBSs) is critical for accurate earthquake location and Earth model studies. GNSS signals, however, cannot reach OBSs deployed at the ocean bottom. This prevents their clocks from being synchronized with a known reference time. To overcome this, we developed OCloC, a Python package that uses time-lapse cross-correlations of ambient seismic noise to synchronize the recordings of large-scale OBS deployments. By simultaneously quantifying deviations from symmetry of a set of lapse cross-correlations, OCloC recovers the incurred clock errors by means of a least-squares inversion. In fact, because non-uniform noise illumination patterns also break the symmetry of (lapse) cross-correlations, we introduce a distance-based weighted least-squares inversion. This mitigates the adverse effect of the noise illumination on the recovered clock errors. Using noise recordings from the IMAGE project in Reykjanes, Iceland, we demonstrate that OCloC significantly reduces the time and effort needed to detect and correct timing errors in large-scale OBS deployments. In addition, our methodology allows one to evaluate potential timing errors at the time of OBS deployment. These might be caused by incorrect initial synchronization, or by rapidly changing temperature conditions while the OBS is sunk to the sea bottom. Our work advances the use of OBSs for earthquake studies and other applications.@en

Accurate timing of seismic records is essential for almost all applications in seismology. Wrong timing of the waveforms may result in incorrect Earth models and/or inaccurate earthquake locations. As such, it may render interpretations of underground processes incorrect. Ocean bottom seismometers (OBSs) experience clock drifts due to their inability to synchronize with a GNSS signal (with the correct reference time), since electromagnetic signals are unable to propagate efficiently in water. As OBSs generally operate in relatively stable ambient temperature, the timing deviation is usually assumed to be linear. Therefore, the time corrections can be estimated through GPS synchronization before deployment and after recovery of the instrument. However, if the instrument has run out of power prior to recovery (i.e., due to the battery being dead at the time of recovery), the timing error at the end of the deployment cannot be determined. In addition, the drift may not be linear, e.g., due to rapid temperature drop while the OBS sinks to the seabed. Here we present an algorithm that recovers the linear clock drift, as well as a potential timing error at the onset. The algorithm presented in this study exploits seismic interferometry (SI). Specifically, time-lapse (averaged) cross-correlations of ambient seismic noise are computed. As such, virtual-source responses, which are generally dominated by the recorded surface waves, are retrieved. These interferometric responses generate two virtual sources: a causal wave (arriving at a positive time) and an acausal wave (arriving at a negative time). Under favorable conditions, both interferometric responses approach the surface-wave part of the medium's Green's function. Therefore, it is possible to calculate the clock drift for each station by exploiting the time-symmetry between the causal and acausal waves. For this purpose, the clock drift is calculated by measuring the differential arrival times of the causal and acausal waves for a large number of receiver-receiver pairs and computing the drift by carrying-out a least-squares inversion. The methodology described is applied to time-lapse cross-correlations of ambient seismic noise recorded on and around the Reykjanes peninsula, SW Iceland. The stations used for the analysis were deployed in the context of IMAGE (Integrated Methods for Advanced Geothermal Exploration) and consisted of 30 on-land stations and 24 ocean bottom seismometers (OBSs). The seismic activity was recorded from spring 2014 until August 2015 on an area of around 100 km in diameter (from the tip of the Reykjanes peninsula).@en

Synthetic aperture radar (SAR) image coregistration is a key procedure before interferometric SAR (InSAR) time-series analysis can be started. However, many geophysical data sets suffer from severe decorrelation problems due to a variety of reasons, making precise coregistration a nontrivial task. Here, we present a new strategy that uses a pixel-offset series of detected subimage patches dominated by point-like targets (PTs) to improve SAR image coregistrations. First, all potentially coherent image pairs are coregistered in a conventional way. In this step, we propose a coregistration quality index for each image to rank its relative 'significance' within the data set and to select a reference image for the SAR data set. Then, a pixel-offset series of detected PTs is made from amplitude maps to improve the geometrical mapping functions. Finally, all images are resampled depending on the pixel offsets calculated from the updated geometrical mapping functions. We used images from a rural region near the North Anatolian Fault in eastern Turkey to test the proposed method, and clear coregistration improvements were found based on amplitude stability. This enhanced the fact that the coregistration strategy should therefore lead to improved InSAR time-series analysis results. © 2014 IEEE.@en