The application of floating wind turbines is limited by the high cost that increases with the water depth. Offshore installation and maintenance continue to consume a high percentage of the project budget. To improve the installation efficiency of the floating offshore wind turbine, a novel concept is proposed by the SFI MOVE project. Several wind turbine superstructure components are preassembled onshore and carried to the installation site by a catamaran construction vessel. Each assembly can then be installed using only one lift, and the concept is less sensitive to weather conditions. In this paper, a control algorithm of the proposed hydraulic active heave compensator system is developed using singular perturbation theory to cancel the relative motion between the spar top and gripped preassembly bottom. Closed-loop stability is proven, and the simulation results show that the installation efficiency is improved with an increase in the acceptable weather conditions.

Rain-induced leading-edge erosion (LEE) of wind turbine blades (WTBs) is associated with high repair and maintenance costs. The effects of LEE can be triggered in less than 1 to 2 years for some wind turbine sites, whereas it may take several years for others. In addition, the growth of erosion may also differ for different blades and turbines operating at the same site. Hence, LEE is a site- and turbine-specific problem. In this paper, we propose a probabilistic long-term framework for assessing site-specific lifetime of a WTB coating system. Case studies are presented for 1.5 and 10 MW wind turbines, where geographic bubble charts for the leading-edge lifetime and number of repairs expected over the blade's service life are established for 31 sites in the Netherlands. The proposed framework efficiently captures the effects of spatial and orographic features of the sites and wind turbine specifications on LEE calculations. For instance, the erosion is highest at the coastal sites and for sites located at higher altitudes. In addition, erosion is faster for turbines associated with higher tip speeds, and the effects are critical for such sites where the exceedance probability for rated wind conditions are high. The study will aid in the development of efficient operation and maintenance strategies for wind farms.

Being one of the most commonly used offshore operations, offshore lifting operations become increasingly challenging due to the gradually growing size and weight of payloads. The research on automatic control in lifting operations, e.g., anti-swing control and heave compensation, only considers simple-shaped payloads, such as lumped-mass rigid points. However, the sizes and orientations of many structures cannot be neglected. To lift heavy and large-scale payloads, larger and higher cranes are required. Alternatively, it is possible to share the total loads by enhancing the number of lift wires that may limit the tension on each lift wire. However, the complicated configuration introduces significant complexity into the design of the automatic anti-swing algorithm, especially to the control allocation module. This paper performs a preliminary study on the anti-swing control of a complex-shaped suspended payload lift using a floating crane vessel and a large number of lift wires. Inspired by the knowledge of inverse dynamics and range-based localization, a general model-free anti-swing control scheme is proposed. The controller has a simple form without considering state–space equations, but it can reduce the pendular payload motion regardless of the detailed system configuration. An offshore wind turbine tower–nacelle–rotor preassembly installation using floating crane vessel is adopted as a case study to verify the performance of the proposed control strategy.

Leading edge erosion (LEE) repairs of wind turbine blades (WTBs) involve infield application of leading edge protection (LEP) solutions. The industry is currently aiming to use factory based LEP coatings that can applied to the WTBs before they are shipped out for installation. However, one of the main challenges related to these solutions is the choice of a minimum LEP application length to be applied in the spanwise direction of the WTBs. Generally, coating suppliers apply 10–20 m of LEP onto the blades starting from the tip of the blade using the “rule of thumb”, and no studies in the literature exist that stipulate how these LEP lengths can be calculated. In this study, we extend the scope of a recently developed long-term probabilistic framework to determine the minimum LEP application length required for WTBs to combat rain-induced erosion. A parametric study is performed where different wind turbines with varying power ratings of 2.1 MW to 15 MW at different Dutch sites ranging from inland to coastal are considered. The results of the study show that the LEP application length is sensitive to the choice of the site, as well as the turbine attributes. Further, LEP lengths for WTBs are found to be the highest for turbines installed at coastal sites and turbines with higher power ratings. A detailed investigation is further performed to check the sensitivity of the LEP application length with the wind turbine parameters. The results of the study are expected to provide guidelines to the industry for efficient repair strategies for WTBs.

The presence of rain-induced leading edge erosion of wind turbine blades (WTBs) necessitates the development of erosion models. One of the essential parameters for erosion modeling is the relative impact velocity between rain droplets and the rotating blade. Based on this parameter, the erosion damage rate of a WTB is calculated to estimate the expected leading edge lifetime. The environmental conditions that govern this parameter have site-specific variations, and thus, rain and wind loading on a turbine differ for onshore and offshore locations. In addition, there are wave loads present in the offshore environment. The present paper tries to provide guidelines for erosion modeling and investigates whether there are differences in erosion of blades due to (1) varying rainfall conditions modeled using different droplet size distributions for onshore and offshore locations in combination with (2) winds of varying turbulence intensities and (3) wave-induced loads. Aero-hydro-servo-elastic simulations are carried out for an onshore wind turbine (WT) and a monopile-supported offshore WT. Furthermore, erosion variables such as the relative impact velocities and the associated erosion damage rate of a blade are analyzed for various blade azimuth angles. The study shows that the rainfall intensity and turbulence intensity minorly influence the impact velocity and pressure but have a substantial effect on the overall erosion damage rate. Additionally, a significantly higher erosion damage rate is found for blades exposed to offshore rainfall conditions than for blades under onshore rainfall conditions. Furthermore, no substantial influence on erosion is found because of wave-induced loads.

Floating structures oscillate in waves, where these wave-induced motions may be critical for various marine operations. An important consideration is thereby given to the sea states at the planning and operating stages for an offshore project. The most important information extracted from a sea state is the directional wave spectrum, indicating wave direction, significant wave height, and wave spectrum peak period. Among several available methods of measuring and estimating the directional wave spectrum, the wave buoy analogy technique based on vessel motion responses is an in situ and almost real-time solution without extra costs of devices. If the forms of the wave spectra are not predefined in the estimation, the method is called a nonparametric approach. Its most remarkable advantage is the flexible form, but the smoothness should be regulated. After the discrete Fourier transform has been applied to the measured vessel motions, smoothing is necessary. However, this process results in disturbed vessel cross-spectra and a lowpass characteristic of the windowing function. This paper presents a nonparametric approach for directional wave spectrum estimation based on vessel motion responses. It introduces novel smoothness constraints using Bézier surface and includes a more robust estimate using L1 optimization. Both techniques are applied to the wave buoy analogy for the first time. Numerical simulations are conducted to verify the proposed algorithm.

Operations and maintenance of offshore wind turbines (OWTs) play an important role in the development of offshore wind farms. Compared with operations, maintenance is a critical element in the levelized cost of energy, given the practical constraints imposed by offshore operations and the relatively high costs. The effects of maintenance on the life cycle of an offshore wind farm are highly complex and uncertain. The selection of maintenance strategies influences the overall efficiency, profit margin, safety, and sustainability of offshore wind farms. For an offshore wind project, after a maintenance strategy is selected, schedule planning will be considered, which is an optimization problem. Onsite maintenance will involve complex marine operations whose efficiency and safety depend on practical factors. Moreover, negative environmental impacts due to offshore maintenance deserve attention. To address these issues, this paper reviews the state-of-the-art research on OWT maintenance, covering strategy selection, schedule optimization, onsite operations, repair, assessment criteria, recycling, and environmental concerns. Many methods are summarized and compared. Limitations in the research and shortcomings in industrial development of OWT operations and maintenance are described. Finally, promising areas are identified with regard to future studies of maintenance strategies.

Most wind turbine blades are assembled piece-by-piece onto the hub of a monopile-type offshore wind turbine using jack-up crane vessels. Despite the stable foundation of the lifting cranes, the mating process exhibits substantial relative responses amidst blade root and hub. These relative motions are combined effects of wave-induced monopile motions and wind-induced blade root motions, which can cause impact loads at the blade root’s guide pin in the course of alignment procedure. Environmental parameters including the wind-wave misalignments play an important role for the safety of the installation tasks and govern the impact scenarios. The present study investigates the effects of wind-wave misalignments on the blade root mating process on a monopile-type offshore wind turbine. The dynamic responses including the impact velocities between root and hub in selected wind-wave misalignment conditions are investigated using multibody simulations. Furthermore, based on a finite element study, different impact-induced failure modes at the blade root for sideways and head-on impact scenarios, developed due to wind-wave misalignment conditions, are investigated. Finally, based on extreme value analyses of critical responses, safe domain for the mating task under different wind-wave misalignments is compared. The results show that although misaligned wind-wave conditions develop substantial relative motions between root and hub, aligned wind-wave conditions induce largest impact velocities and develop critical failure modes at a relatively low threshold velocity of impact.

Leading edge erosion (LEE) of a wind turbine blade (WTB) is a complex phenomenon that contributes to high operation and maintenance costs. The impact between rain droplets and rotating blades exerts cyclic fatigue stresses on the leading edge - causing progressive material loss and reduced aerodynamic performance. One of the most important parameters for erosion modelling and damage prediction is the relative impact velocity between rain droplets and rotating blade and depends upon the environmental conditions. The environmental condition, in general, could vary for onshore and offshore wind turbines (OWTs) - for instance, the presence of wave-induced loads along with less turbulent wind and varying rainfall conditions in the offshore environment. The present paper tries to provide guidelines whether all these parameters need to be included for LEE modelling. Aero-hydro-servo-elastic simulations are carried out for a rotating blade based on the NREL 5 MW turbine by considering realistic environmental conditions for a land-based wind turbine and monopile-supported OWT. Further, the impact velocities and erosion damage rate, evaluated using a surface fatigue model, are analysed and compared for different environmental conditions. It is found that rainfall intensity and turbulence intensity influences the impact velocity minorly, however, has a substantial effect on the overall erosion damage rate. For instance, for the investigated load cases, an 8% increase in the impact velocity is observed when the turbulence intensity increases from 6% to 26%, which indicates an increase of erosion damage rate by more than 40%. Furthermore, no substantial influence is found due to the effects of wave-induced loads on the wind turbine.