Induction furnace steel slag is a secondary product obtained when molten steel is separated from the impurities in the steel-producing furnaces. Though numerous studies have been published on the mechanical strength of concrete/mortar made with steel slag as fine aggregate, relatively few studies focus on the shrinkage, durability (i.e., porosity, water absorption, and resistance to chloride penetration) at ambient temperature, and especially the mechanical and durability performances after exposure to elevated temperatures. Within this context, the present study investigates mechanical strength, shrinkage, and durability of mortar made with different contents of steel slag powder (SSP) at two different water-to-cement (w/c) ratios before and after exposure to elevated temperatures (120, 250, 400 and 600 °C). Mortars made with SSP showed significantly higher mechanical strength and better durability than mortar made with 100% natural sand (control mortar). Compressive, tensile, and flexural strength increased by 45%, 72% and 56%, respectively, when SSP entirely replaced natural sand. Porosity, water absorption, and chloride penetration decreased by 42%, 61% and 52%, respectively, for 100% SSP mortar. Furthermore, the shrinkage of the mortar decreased with increasing percentages of SSP. Conversely, residual compressive strength after heat exposure was lower for 100% SSP mortar than for the control mortar. Therefore, this study presents a first step towards the successful utilization of SSP in cementitious mortar.@en

This study evaluates the mechanical, durability, and residual compressive strength (after being exposed to 20, 120, 250, 400 and 600 °C) of mortar that uses recycled iron powder (RIP) as a fine aggregate. Within this context, mechanical strength, shrinkage, durability, and residual strength tests were performed on mortar made with seven different percentages (0%, 5%, 10%, 15%, 20%, 30% and 50%) of replacement of natural sand (NS) by RIP. It was found that the mechanical strength of mortar increased when replaced with up to 30% NS by RIP. In addition, the increase was 30% for compressive, 18% for tensile, and 47% for flexural strength at 28 days, respectively, compared to the reference mortar (mortar made with 100% NS). Shrinkage was observed for the mortar made with 100% NS, while both shrinkage and expansion occurred in the mortar made with RIP, especially for RIP higher than 5%. Furthermore, significantly lower porosity and capillary water absorption were observed for mortar made with up to 30% RIP, compared to that made with 100% NS, which decreased by 36% for porosity and 48% for water absorption. As the temperature increased, the strength decreased for all mixes, and the drop was more pronounced for the temperatures above 250 °C and 50% RIP. This study demonstrates that up to 30% RIP can be utilized as a fine aggregate in mortar due to its better mechanical and durability performances. @en

Studies have shown that the incorporation of waste tire rubber aggregates reduces the strength, increases permeability and decrease thermal conductivity of concrete. However, only a few studies have investigated the effect of surface-modified rubber aggregates on the properties of concrete. This study investigates the effect of the surface treatment of waste tire rubber as coarse aggregates with different oxidizing solutions and different treatment durations on the mechanical, durability and thermal properties of concrete. The properties of concrete incorporated with 8% rubber coarse aggregates (by volume of natural aggregates) which were treated with three different solutions: water (H2O), 20% sodium hydroxide (NaOH) and 5% calcium hypochlorite [Ca(ClO)2] (both as% weight of water) for durations of 2, 24, and 72 h, respectively. The effect of these treatments on the compressive strength, splitting tensile strength, water permeability, thermal conductivity and diffusivity of concrete was investigated. Results show that Ca(ClO)2 has a more positive effect on the strength and permeability compared to NaOH solution and water. Experimental results were statistically analyzed using ANOVA and Post Hoc tests. The analyses showed that the improvement of concrete strength is only significant when the treatment with NaOH and Ca(ClO)2 is prolonged to 72 h. Furthermore, the microstructural analysis of concrete showed that the improvement in the strength is due to the improved bonding between cement paste and rubber aggregates as a result of surface treatment. This microstructural improvement also resulted in lower water permeability of concrete. However, the thermal conductivity and diffusivity increased when the surface treatment duration increases as there are less air voids in the samples. This study shows that, with appropriate pretreatment, a certain percentage of natural aggregates can be safely replaced with waste tire rubber aggregates while maintaining sufficient quality of the resulting concrete.@en

Disposal of consumer waste is a major challenge in urban areas around the world. In the field of building materials, it has long been recognized that many types of wastes can be used instead of raw materials. In addition, production of binders such as Portland cement is a CO₂ intensive process. However, for widespread use of wastes in construction, it is important that the properties of resulting building materials are satisfactory. For concrete, the most important are the fresh, hardened and durability properties. A promising waste material that can be utilized to create sustainable concrete composites is waste recycled glass. In this paper, literature dealing with use of waste recycled glass as partial replacement of either cement or aggregate in concrete is systematically reviewed. The focus of this review is the influence of recycled waste glass on the engineering properties of concrete. Main advantages and drawbacks of using recycled waste glass are discussed. The aim of this review is to identify major research needs in the field that will help bring this class of materials closer to worldwide practical use. Given that concrete is the most used man-made material in the world, such development would significantly reduce the need for landfilling of waste recycled glass that is unsuitable for reuse in glass production.

@en

The abundance of waste plastic is a major issue for the sustainability of the environment as plastic pollutes rivers, land, and oceans. However, the versatile behavior of plastic (it is lightweight, flexible, strong, moisture-resistant, and cheap) can make it a replacement for or alternative to many existing composite materials like concrete. Over the past few decades, many researchers have used waste plastic as a replacement for aggregates in concrete. This paper presents a comprehensive review of the engineering properties of waste recycled plastic. It is divided into three sections, along with an introduction and conclusion. The influence of recycled waste plastics on the fresh properties of concrete is discussed first, followed by its influence on the mechanical and durability properties of concrete. Current experimental results have shown that the mechanical and durability properties of concrete are altered due to the inclusion of plastic. However, such concrete still fulfills the requirements of many engineering applications. This review also advocates further study of possible pre-treatment of waste plastic properties for the modification of its surface, shape, and size in order to improve the quality of the composite product and make its use more widespread@en