The clinker in cement largely determines the environmental footprint of concrete. Therefore, concrete recycling should focus on retrieving high-quality cementitious fractions to replace clinker. This requires a shift from current traditional recycling techniques towards innovative recycling methods, enabling recovery of not only clean secondary aggregates, but also residual cementitious fines (RCF), potentially eliminating the carbon dioxide emissions associated with them. The production and upcycling of RCF offer new implementation routes that were previously deemed unfeasible. However, the properties of RCF may vary based on their origin, affecting their replacement and upcycling potential. Consequently, assessing the original concrete quality, with a focus on the binder type, before demolition is important. A handheld x-ray fluorescence technique appears promising for this purpose. To achieve effective separation of clean secondary aggregates from the original cementitious content, innovative crushing and separation techniques are needed. Additionally, electrostatic separation shows significant research potential for further optimizing RCF.@en

This paper draws attention to the environmental impact of passive smart windows, a novel high-performance glazing technologies that can change their solar transmittance to control the amount of solar gain, thus reducing cooling energy demand. Despite the large influence of building envelope technologies on overall embodied carbon in buildings, the environmental impact of passive smart windows has been inadequately addressed, with a dearth of numerical data on various impact categories beyond energy consumption and Global Warming Potential (GWP). While current literature focuses on the advantages of these technologies in terms of operational energy savings, other critical environmental considerations are currently missing. This paper aims to bridge the existing gap by introducing a novel framework for evaluating the broader environmental impact of passive smart windows through a multi-category LCA method. By analysing the life cycle of these technologies, including production, usage, and disposal, the research seeks to provide a holistic understanding of their contribution to sustainability. The framework is based on systematic literature review on current state-of-art approaches and Interviews with key stakeholders in the dynamic glazing value chain. Literature review and interview results are presented, and then the framework is demonstrated through a case study of a thermochromic technologies for an office building in the Netherlands. Preliminary results show the critical areas where improvements on the methods or on the performance of the technology are required for the achievement of holistically sustainable high-performing glazing.@en

Given the ongoing global urbanization and the rise of heat, flooding, and drought in cities, the integration of climate adaptive measures based on “ecosystem functions and services” becomes imperative in design. This study details the implementation process of a microclimate design model in the design and retrofitting of the housing project Ecohof Noorderveer in Wormerveer, the Netherlands. The model, which quantifies local urban heat and mitigating measures through ecosystem functionalities, was incorporated into the program of requirements. The design process followed a research-by-design trajectory, involving iterative creative collaboration among all stakeholders, including future residents, the municipality, the water board, and the architect. The research employed the CFIR method to compare anticipated implementation outcomes with actual results. The findings suggest that introducing the microclimate design model into the program of requirements proved beneficial for the implementation process in the early design stage. The research-by-design approach was also deemed helpful, contingent on careful involvement of all participants in the knowledge-sharing process. This implementation method demonstrates significant potential for scaling up to standard urban development projects.@en

The environmental footprint of concrete is largely influenced by the binder. It is therefore of high interest to investigate the potential reuse of the binder retrieved by modern separation techniques. However, studies found that the recycled cement fraction (RCF) still contained a certain amount of siliceous concrete aggregates, which forms an obstacle in the upcycling of RCF. In this study, the potential of electrostatic separation as a method to separate cementitious binder (hydrated and unhydrated) and sand (silica) is evaluated. Different cementitious powders and silica (sand) were prepared, resulting in a total of 9 powders and 8 mixtures. The mixtures consisted of a combination of silica and one of the cementitious powders (50/50 wt%) with a particle size of the components <125 μm. The potential of the studied technique was evaluated through charging measurements and x-ray fluorescence (XRF). Silica was assumed to contain no CaO and the detected CaO was therefore assigned to the cementitious powders. Results showed that silica and silica-rich fly ash (FA) particles became negatively charged, blast furnace slag (BFS) particles remained largely charge neutral and all other cementitious particles obtained a positive charge. Through electrostatic separation an enrichment of the cementitious binder fraction for all mixtures was obtained at the negative electrode. FA-Silica achieved the highest enrichment (89.9%), CEM III/B-Silica the lowest (4.7%) and the hydrates were enriched ranging from 28.0 to 31.8%.@en

De essentie van het goed nabehandelen van beton is al vaak besproken. Nabehandeling is noodzakelijk voor beton met een lange levensduur en een mooi uiterlijk. Een CROW-onderzoek naar betonaantasting in combinatie met mosgroei was aanleiding het thema nogmaals te bestuderen. Resultaat is een nieuw studierapport van Stutech-studiegroep 68 ‘Nabehandeling’.@en

Implementing nature in cities has great potential to improve urban liveability by providing ecosystem services, which can help mitigate heat stress, improve air quality, attenuate noise, and reduce rainwater run-off. However, widespread adoption of urban nature and green building typologies is still limited due to their costs, environmental impact, and space constraints. Bioreceptive concrete can form the basis of a new green building typology, where the concrete mixture is adjusted to allow for biological growth, specifically mosses, to occur on its surface. This literature review aims to give an overview of the current state of the art on bioreceptive concrete as a material in general and specifically the (potential) ecosystem services provided by the mosses growing on this bioreceptive concrete. This review shows that bioreceptivity can be achieved in concrete in several ways, including minor adjustments to standard concrete recipes. While quantitative data on the ecosystem services provided by mosses in an urban context is still limited, potential gains appear significant. The main challenges lie in the durable long-term development of mosses on the bioreceptive concrete and the valuation through quantification of the ecosystem services they provide. However, moss-receptive concrete shows promise as a new green building typology if these challenges are bridged. @en

Potted plants have been reported to uptake VOCs and help “cleaning” the air. This paper presents the results of a laboratory study in which two species of plants (peace lily and Boston fern) and three kinds of substrates (expanded clay, soil, and activated carbon) were tested and monitored on their capacity to deplete formaldehyde and CO2 in a glass chamber. Formaldehyde and CO2 were selected as indicators to evaluate the biofiltration efficacy of 28 different test conditions; relative humidity (RH) and temperature (T) were monitored during the experiments. To evaluate the efficacy of every test, the clean air delivery rate (CADR) was calculated. Overall, soil had the best performance in removing formaldehyde (~0.07–0.16 m3/h), while plants, in particular, were more effective in reducing CO2 concentrations (peace lily 0.01m3/h) (Boston fern 0.02–0.03 m3/h). On average, plants (~0.03 m3/h) were as effective as dry expanded clay (0.02–0.04 m3/h) in depleting formaldehyde from the chamber. Regarding air-cleaning performance, Boston ferns presented the best performance among the plant species, and the best performing substrate was the soil@en

Asphalt pavement consists of aggregates resulting in a waste material at end of its life. The aggregates can be reused as basic material for asphalt or cementitious binding agents. In both scenarios, the recycled aggregates should provide a good bond with the binder to achieve strength. This study focuses on reusing recycled asphalt aggregates (RAA) in mortar. The major weakness of RAA is the thin oily film originating from the asphalt residue, weakening the bond with cement. The pyrolysis method is accessed in an attempt to overcome this weakness. Three scenarios were investigated; the use of virgin aggregates (VA), RAA, and pyrolysis recycled asphalt aggregate (PRAA) as constituent in mortar. All variables were set a constant except for the aggregate type, the VA mortar function as controlling element. This research is methodologically based on experimental data conducted in the laboratory, while aggregate samples were taken from the field. To analyze the influence of pyrolysis to the aggregate-to-cement bond behaviour, qualitative and quantitative data were collected. The quantitative data were the mechanical properties, the mortar tensile, and compression strength. The qualitative data were obtained from scanning electron microscope readings to visually observe the aggregate surface roughness and voids, including the aggregates cross-section and pre-existing micro-cracks in the aggregate-to-cement interface. Supporting data were the aggregates‘ abrasion rate and absorption. The RAA resulted in a significant mortar strength decrease. This conclusion was supported by the findings of pre-existing cracks in the interfacial transition zone. The pyrolysis method improved the compression strength but negligibly affected the tensile behavior. The compression and tensile strength increased as a function of time for both RAA and PRAA, and a strength convergence was reached at 28 days. The PRAA is considered an option for reuse in mortar, supporting nature conservation.

@en

The urban heat island, is a serious threat for the urban well-being, and can be determined by the local energy balance. The surface energy balance, with respect to incoming radiative energy and subsequent partitioning into reflected energy (albedo), absorbed energy and further partitioning of latter into convectional heat (QH), radiative heat (QR) and latent heat (QE) by using commonly applied urban materials and vegetation types, was therefore experimentally quantified in this study. In agreement with previous studies it was found that materials convert most of absorbed energy into convectional heat (>92%) while vegetation channels a substantial part of absorbed radiative energy into latent heat (27–50%). It is for the first time experimentally demonstrated that significant differences in thermal behaviour between different types of urban vegetation surfaces occur. Of the investigated vegetation types ivy and moss showed respectively the highest (0.10) and lowest (0.07) albedo, but sedum and moss channelled respectively lowest (27%) and highest (50%) percentage of the absorbed radiative energy into latent heat production. Of the four investigated plant types, moss appeared most effective in preventing UHI, converting only 50% of incoming radiative energy into convectional heat, while sedum was least effective converting 73% of incoming radiative energy into convectional heat. These quantitative measurements show that strategic use of specific types of urban vegetation surfaces, instead of commonly applied building materials, can be an effective measure for mitigation of UHI leading to improved climate resilient cities.@en

Kansen in de circulaire economie zijn er voor beton volop. Hoewel de winst het grootste is door hergebruik van gebouwen of constructies is het bekendste voorbeeld nog altijd het hergebruik van betonpuin als granulaat in nieuw beton. Maar dat laatste levert lang niet altijd een reductie op van de CO₂-uitstoot. Door nieuwe recyclingmethoden kunnen de kwaliteit en vervangingspercentage van het granulaat echter flink worden verhoogd en ontstaan meer kansen met betrekking tot CO₂-reductie. @en

A bioreceptive material allows for biological content (biofilms) to grow on it, without necessarily affecting the material itself. If a bioreceptive concrete could therefore be integrated into a building façade, it could lead to green façades that do not need additional technical systems. As part of previous research by the authors, a promising bioreceptive concrete mixture was formulated. The aim of this research is to develop this concept by using the previously developed mixture to create a bioreceptive concrete façade panel prototype, made using commonly available materials, that can direct where the biological growth takes place. The latter is done by combining the bioreceptive concrete with a non-bioreceptive (UHPC-based) concrete in the same panel, through a two-stage pouring process. A biofilm was developed on this prototype panel and results show that full coverage of the bioreceptive parts of the panel can be achieved within two weeks under optimal growing conditions and biological growth can be directed. However, exterior survivability is an issue for now. The concept of bioreceptive façades therefore shows promise, yet further investigation into improving exterior survivability is necessary, while further research into the underlying ecology, material, economics, and climate effects is also necessary.@en

Increased urbanisation will put an increasing strain on our green spaces, which is expected to have a significant effect on our physical and mental health, as well as the health of our ecosystems. As such it is important to integrate more green spaces in our urban fabric. One way of doing this is by making use of so-called bioreceptive concrete on our façades and other structures, which allows for biological growth to take place on the concrete substrate itself, without requiring any additional systems or maintenance. However, the challenge is to create an affordable concrete mixture that is sufficiently bioreceptive for biological growth to take place. As such, in our research we test four possible measures to make concrete more bioreceptive: changing the aggregate to CEC (crushed expanded clay), adding bone ash to the mixture, increasing the wcf (water cement factor) and using a surface retarder on the concrete. Of these measures, changing the aggregate to CEC (p = 0.024), the addition of bone ash (p = 0.022) and the use of a surface retarder (p < 0.001) were found to significantly increase bioreceptivity. Increasing the wcf factor, however, was not found to significantly increase bioreceptivity (p = 0.429). It was also found that whereas it was previously though a pH below 10 is necessary for biological growth to take place, this does not appear to be the case. Although further research under natural conditions is necessary, the creation of an inexpensive bioreceptive concrete looks to be feasible.@en

Active plant-based systems are emerging technologies that aim to improve indoor air quality (IAQ). A person’s olfactory system is able to recognize the perceived odor intensity of various materials relatively well, and in many cases, the nose seems to be a better perceiver of pollutants than some equipment is. The aim of this study was to assess the odor coming out of two different test chambers in the SenseLab, where the participants were asked to evaluate blindly the level of acceptability, intensity, odor recognition, and preference at individual level with their noses. Two chambers were furnished with the same amount of new flooring material, and one of the chambers, Chamber A, also included an active plant-based system. The results showed that in general, the level of odor intensity was lower in Chamber B than in Chamber A, the level of acceptability was lower in Chamber A than in Chamber B, and the participants identified similar sources in both chambers. Finally, the preference was slightly higher for Chamber B over Chamber A. When people do not see the interior details of a room and have to rely on olfactory perception, they prefer a room without plants. @en

Bio-receptivity refers to the aptitude of a material to allow for the natural growth of small plant species on stony surfaces with minimum external influence. Despite the numerous associated environmental benefits, the growth of mosses and lichens on facades has always been viewed as a negative phenomenon due to the random and shabby growth conditions. This research dealt with the design of a self-sustaining bio-receptive concrete facade system with an aim to create a more sustainable and green concrete for the construction industry. The research used surface geometry as a design variable to facilitate moss growth on concrete panels in an ordered and systematic manner. The exercise was an attempt to not only address the functional aspect of bio-receptivity but also its aesthetical quality, which has a primary influence on people’s perception of bio-receptivity and can promote mass use of this type of concrete material. The research was conducted in a top-down approach, where first, through design by research, six distinctly designed concrete panels were fabricated using adapted material composition (blast furnace cement with 75% slag, 0.6 water/cement, sand 0–4 mm and gravel 5–8 mm) as the boundary condition. The concrete mixture together with no curing policy resulted in highly porous concrete panels, suitable for bio-receptive properties. Next in the design validation phase, the influence of surface geometry/roughness on the water retention ability of the panels and the subsequent moss growth on the panels were evaluated through in vitro experiments. The water retention experiment of the panels was based on quantitative measurements for weight, relative humidity and temperature at several time intervals. The moss-growing experiment was carried out within an ideal greenhouse condition where the panels were initially inoculated with moss spores; the results were based on qualitative observation for a period of 4 months. According to the comparative analysis of these results, with the same material composition, Panel 2 showed the highest bio-colonization owing to its prominent surface geometry, whereas Panel 5 showed the least bio-colonization owing to its plain surface despite high absorption capacity. Thus, the role of geometry has been extensively proven in this research and as an outcome a set of general design guidelines have been formulated for a self-sustaining bio-receptive concrete facade panel, using geometry as a design variable for bio-receptivity.@en

Bijna alle stedelijke klimatologische problemen zijn te herleiden naar het ontbreken van ecosysteemdiensten. Dat blijkt uit onderzoek van de TU Delft Faculteit Civiele Techniek, afdeling Materialen en Duurzaamheid. ‘Ook vonden we dit gebrek medeverantwoordelijk voor veel stedelijke sociale problemen,’ aldus de auteurs. Op basis van het onderzoek ontwikkelden zij een module die inzicht verschaft in de verbeteringen die ecosysteemdiensten ons bieden.@en

Examining the actual major environmental and social problems of the modern city, e.g., pollution, difficulties in food and water supply, poverty or homelessness, this study argues that insights from the field of ecology could offer structural solutions. In particular, specific ecosystem services could be used to fight/solve specific urban problems. Today, on a large scale, only a few different ecosystem services from outside the urban area are used as ecosystems, as biotopes are insufficiently available inside the city boundary. Their physical absence obstructs the use of their benefits and leaves an important potential of urban ecological space unused. Most vegetation was banned from cities during urban history, what may have been the fundamental cause of several major urban problems emerging today. Therefore, the solving potential was analyzed of 20 ecological services if consistently located inside the urban boundary. According to the results, respectively, 14 and 7 ecosystem services can be linked as solutions to 10 environmental and 8 social problems eminent in contemporary cities. This study, therefore, concludes that structural integrating ecosystem services in the built-up urban space: (1) could solve major urban environmental and social problems; (2) improve urban sustainability; (3) revitalize degraded urban areas.@en

This paper reviews the state of art of vegetation systems and their effect on the indoor environmental quality (IEQ), based on scientific studies from the past 30 years. Some studies have shown that biophilic workspaces and interaction with plants may change human attitudes, behaviours, improve productivity and the overall well-being. Evapotranspiration from plants helps lowering the temperature around the planting environment and this can be utilised for air cooling and humidity control. Also, indoor greenery can be used to reduce sound levels as a passive acoustic insulation system. Living wall systems in combination with biofiltration are emerging technologies to provide beneficial effects on improvement of indoor comfort. Several studies have indicated that green systems may improve indoor air quality and that they have different pathways for pollutant removal of volatile organic compounds. The plant root zone in potted plants may be an effective area for removing volatile organic compounds under controlled conditions. In conclusion, the full capacity of plants in real-life settings will need to be clarified to establish the true pollutant-removal mechanisms and the general effect on IEQ. The effects of green systems in combination with mechanical elements such as conventional heating, ventilation and air conditioning would need to be studied.

@en

Owners of concrete structures would benefit from knowing when to expect corrosion initiation in a particular structure. Presently, no accepted procedures for testing existing structures for the remaining time to corrosion initiation are available. This paper proposes such a procedure, based on our experience and additional considerations. From about 20 years age, existing structures contain the concrete’s response to actual environmental loads, e.g. chloride ingress profiles. By measuring the actual cover depth, taking chloride profiles, assuming a few parameters and a simple model, the expected time to corrosion initiation for a particular test area can be predicted. Numbers of cores and samples per core are given. Uncertainties can be taken into account by applying a calculatory reduction of the cover depth. Results of at least six cores per test area are classified and suggested interpretations are given. Because of large variability, the results are classified in three ranges of time to corrosion initiation: five years or less, five to fifteen years, or more than 15 years. The procedure has been approved by the relevant national Standards committees and is issued early 2018. It was applied to a field case and the obtained results are discussed. @en

Groen in de stedelijke omgeving, zoals bomen en struiken, hebben een positieve werking op het welzijn van de mens. Zo blijken mensen te herstellen van stress en vermoeidheid en leidt groen tot minder gezondheidsklachten. Verschillende bladkleuren en geuren kunnen bijdragen aan een aangenaam gevoel. En de stad wordt levendiger doordat planten door de seizoenen heen veranderen.@en

Vegetation systems in combination with biofiltration processes are emerging processes that are expected to have beneficial effects on the improvement of indoor air quality (IAQ). Common indoor plants may provide a valuable strategy to avoid rising levels of indoor air pollution. In an active vegetation system air cleaning rates may be significantly higher than in passive vegetation systems using active fan-assisted hydroponics technology, which draws the air through the root rhizomes of the plants. However, to evaluate the real effect of active green systems on IAQ it is important to create a reliable experimental setup and protocol regarding not only components of the prototype but also the methods for analysis and evaluation.@en