A standard procedure in processing vertical seismic profile (VSP) data is the separation of up-and downgoing wavefields. We show that the up-down wavefields in boreholes can be reconstructed using only singlecomponent borehole data, given that a full set of surface reflection data is also available. No medium parameters are required. The method is wave-equation based for a general inhomogeneous lossless medium with moderately curved interfaces. It relies on a focusing wavefield from the Marchenko method, which gives the recipe for finding this wavefield that satisfies certain focusing conditions in a reference medium. The up-down wavefields are then reconstructed at borehole positions using this focusing wavefields and the surface reflection response. We show that the method is applicable to boreholes with any general orientation. The requirement is that the source positions in the surface data are regularized to be the same as those in the borehole data, and that source deconvolution and surface multiple removal are applied for the surface data. Numerical results from a field in the North Sea are shown, and three different borehole geometries (horizontal, deviated and vertical) are tested. The result shows that the reconstructed up-down wavefields agree well with those by conventional separation methods. @en

Understanding seismic changes in the subsurface is important for reservoir management and health, safety and environmental (HSE) issues. Typically the changes are interpreted based on the time shifts in seismic time-lapse (4D) data, where sources are at the surface and receivers are either at the surface or in a borehole. With these types of acquisition geometry, it is more straightforward to detect and interpret changes in the overburden, close to the source and receivers, than changes in the deeper part close to the reservoir, because the time shift is accumulative along its ray path from source to receiver. We propose a new method for reconstructing the reflection responses of the overburden and the reservoir, separately, for 4D time shift analysis. This method virtually moves sources and receivers to a horizontal borehole level, which enables a more direct interpretation of the time shifts to the changes close to the borehole, instead of to the surface. A realistic field model is used to demonstrate the method, and we observe a clear discrimination of the different time shifts in the overburden and reservoir, which is not obvious in the original datasets.@en

A novel application of seismic interferometry (SI) and Marchenko imaging using both surface and borehole data is presented. A series of redatuming schemes is proposed to combine both data sets for robust deep local imaging in the presence of velocity uncertainties. The redatuming schemes create a virtual acquisition geometry where both sources and receivers lie at the horizontal borehole level, thus only a local velocity model near the borehole is needed for imaging, and erroneous velocities in the shallow area have no effect on imaging around the borehole level. By joining the advantages of SI and Marchenko imaging, a macrovelocity model is no longer required and the proposed schemes use only single-component data. Furthermore, the schemes result in a set of virtual data that have fewer spurious events and internal multiples than previous virtual source redatuming methods. Two numerical examples are shown to illustrate the workflow and to demonstrate the benefits of the method. One is a synthetic model and the other is a realistic model of a field in the North Sea. In both tests, improved local images near the boreholes are obtained using the redatumed data without accurate velocities, because the redatumed data are close to the target. @en

The standard requirement for up-down wavefield separation in seismic data is to use multi-component data. An important application for such separation is to remove the interference from multiple reflections from either the free surface or the internal subsurface structures. As an alternative, we propose an automatic scheme of estimating the up-down wavefields in a horizontal borehole using only single component measurements. The scheme builds upon recent developments of the Marchenko method. The up-down fields are constructed essentially from the surface reflection response (surface seismic data), together with the direct waves' travel time from the borehole data. No prior information of the subsurface is needed, and an automatic working flow is suggested. The numerical test using a synthetic field model shows good results compared to that from a conventional multi-component approach. @en

In the field of seismic interferometry, researchers have retrieved surface waves and body waves by cross-correlating recordings of uncorrelated noise sources to extract useful subsurface information. The retrieved wavefields in most applications are between receivers. When the positions of the noise sources are known, inter-source interferometry can be applied to retrieve the wavefields between sources, thus turning sources into virtual receivers. Previous applications of this form of interferometry assume impulsive point sources or transient sources with similar signatures. We investigate the requirements of applying inter-source seismic interferometry using nontransient noise sources with known positions to retrieve reflection responses at those positions and show the results using synthetic drilling noise as source. We show that, if pilot signals (estimates of the drill-bit signals) are not available, it is required that the drill-bit signals are the same and that the phases of the virtual reflections at drillbit positions can be retrieved by deconvolution interferometry or by cross-coherence interferometry. Further, for this case, classic interferometry by cross-correlation can be used if the source power spectrum can be estimated. If pilot signals are available, virtual reflection responses can be obtained by first using standard seismic-whiledrilling processing techniques such as pilot cross-correlation and pilot deconvolution to remove the drill-bit signatures in the data and then applying cross-correlation interferometry. Therefore, provided that pilot signals are reliable, drill-bit data can be redatumed from surface to borehole depths using this inter-source interferometry approach without any velocity information of the medium, and we show that a well-positioned image below the borehole can be obtained using interferometrically redatumed reflection responses with just a simple velocity model. We discuss some of the practical hurdles that restrict the application of the proposed method offshore. @en