Person | TU Delft Repository

M.S. Ibrahim

View Pure Profile

4 records found

Authored

Effect of concrete cover on the pure torsional behavior of reinforced concrete beams

Analytical model

Journal article (2024) - M.S. Ibrahim, M.S. Ibrahim, Esayas Gebreyouhannes

Experimental data on RC members subjected to pure torsion is compiled from published studies so far. Interestingly, the past studies have concentrated largely on members with small to moderate concrete covers, with handful data on members with thick concrete cover. Widely accepted torsion models including the diagonal compression field theory (CFT), softened truss model (STM) and softened membrane model for torsion (SMMT) are verified on the domains of experimental data missing-in specimens with thick concrete cover. With increasing demand for durability design of RC structures use of thick concrete cover, say up to 75 mm, is being introduced in practice. Recent experimental investigation by the authors demonstrated that spalling of concrete cover, particularly in cases of thick covers, significantly impacts the torsional behavior of RC members. The present study uses these set of experiments to look at the response prediction capability of the existing advanced models and assess the reliability of existing concrete cover spalling theories. For cases with thick cover, the existing models either did not adequately capture the ultimate capacity or erroneously predicted the torsional behavior of the members due to the different mechanics between RC beams with thin and thick covers. Similarly, the spalling theories failed to fully explain the physically observed spalling behavior. Guided by the recent experimental observations and the apparent gaps, the study provides a rational theory for the spalling of concrete cover. The initiation and gradual evolution of concrete cover spalling is traced by observing the acting spalling moment and spalling resistance formulated in the proposed spalling model. The proposed spalling model inherently assumes members susceptibility to spalling of cover concrete and is governed by, the thickness of the concrete cover, tensile strength of concrete, presence of rebar cage and their location, and size of the member. The theory is unified and can explain the spalling of cover due to torsion as well as shear. Its capability is examined by integrating the approach into existing truss model. When compared with state-of-the-art models, the proposed method provides consistent prediction with a relatively smaller scatter, for cases with thick concrete cover as well.

@en

Measurement of Restraint Moment Effect on Lab Specimens with Precast Girders Made Continuous

Conference paper (2023) - M.S. Ibrahim, M. Poliotti, Y. Yang, M.A.N. Hendriks

Typically precast girders are designed and utilized as simple supported members. Alternatively, the precast girders can be made continuous at the intermediate support using cast-in-place concrete topping. Once the girders are made continuous, time-dependent restraint moments will ...

Challenges on the shear behavior of existing continuous precast girder bridges

Conference paper (2022) - M.S. Ibrahim, Y. Yang, M.A. Roosen, M.A.N. Hendriks

There are a large number of precast girder bridges in the Netherlands that are made continuous utilizing cast in situ layers and cross beams. When controlled by the Eurocode minimum shear reinforcement requirement, the majority of these bridges that were constructed before the 19 ...

Contributed

Modelling the Influence of Non Conforming Stirrup Detailing on Shear Capacity of Existing Reinforced Concrete Beams

Master thesis (2024) - B. van Dijk, Y. Yang, M.S. Ibrahim, J.G. Rots, M.A.N. Hendriks, B. Jongstra

In the Netherlands, numerous bridges face reassessment. During this assessment, it is observed that in some cases, the applied shear reinforcement (stirrups) does not meet the detailing requirement given in the national annex of the NEN-EN 1992-2. This requirement, which states that the stirrups must enclose the longitudinal reinforcement to ensure adequate anchorage, is referred by the RBK. This guideline calculates the shear capacity by combining the concrete and the stirrup contribution. However, the contribution of the stirrups can only be included when the detailing requirement is satisfied. In this research, a case study is used in which stirrups are applied that do not meet this requirement. These stirrups are expected to still contribute to the total shear capacity. Therefore, the main aim of this research is to develop a model that can predict the shear capacity by including the anchorage influence of these non conforming stirrups.

In this research, a layered approach is modeled to determine the shear capacity. This approach divides the cross section into several layers, and each of these layers is individually analyzed with the Modified Compression Field Theory (MCFT). The next step in the development of the model is to implement the anchorage behavior. There are two rebar anchorages included in this research; the straight and hooked rebar anchorage. Separate approaches are used to determine the anchorage capacities, which are based on existing experimental research. In both approaches, the axial stress in the applied shear reinforcement could be limited to these anchorage capacities.

Due to the limited availability of experimental research on reinforced concrete beams with non conforming stirrups, this research includes a constrained validation of the model. Subsequently, the shear capacity of the bridge within the case study is predicted. The first cross section in the span region, where the hooked rebar anchorage is governing. As a result of the high anchorage capacity, little influence is observed in the shear capacity of this cross section. The straight rebar anchorage of the stirrup is governing in the support region. This type of anchorage has a greater influence due to the lower anchorage capacity compared to the anchorage capacity of the hooked rebar. However, in both cases, the predicted shear capacity of the model exceeds the concrete shear capacity based on the RBK. Therefore, based on these results, it can be concluded that there is still a contribution of the non conforming stirrups to the total shear capacity.

The proposed model within this research could be used to predict the shear capacity of reinforced concrete beams with non-conforming stirrups. However, for more accurate results, it is recommended to further develop this model to overcome its current limitations. Additionally, it is recommended to conduct more experimental research on these types of beams, due to the limited amount found in literature. Finally, it should be taken into account that the model in this research uses a conservative assumption that the crack is perfectly aligned with the non-conforming stirrup.