Resonant converters are popular in power electronics due to their soft-switching capabilities, which enhance efficiency and prolong component lifetime. Three- phase resonant converters are particularly noteworthy for their higher power density and reduced ripple, making them ideal for demanding applications. A critical aspect of optimizing three-phase LLC resonant converters is the design of a transformer with adequate leakage inductance required for the resonance circuit. This paper compares two distinct transformer designs for such converters: a five-limb shell-type transformer and a symmetrical triangular transformer. Both designs are evaluated in terms of their performance, efficiency, and suitability for integration into the converter architecture. A detailed design procedure using Finite Element Method (FEM) analysis is presented to guide the development of these transformers. The practicality of this approach and its effectiveness are demonstrated through the implementation of a 3.4 kV to 60 V, 50 kVA prototype. This work provides a comparative analysis of transformer designs and introduces a validated methodology for improving the performance of three-phase LLC resonant converters through optimized transformer design.

@en

The correct identification of partial discharges (PDs) is instrumental for the maintenance plan in gas-insulated systems (GIS). However, onsite PD measurements are difficult, especially in HVDC systems, where partial discharges can be confused with interference. This paper proposes a method to discern PDs from interferences based on the GIS characteristic impedance. The characteristic impedance is measured using very-high frequency electric and magnetic sensors, and it is calculated using four approaches based on the PD charge magnitude, peak value, peak-to-peak value, and frequency spectrum. The method is first tested with a PD calibrator in a matched and open-circuited GIS testbench. Then, the identification of PDs and interference is tested in a full-scale GIS, where the measurements are subjected to pulse overlapping and noise. Five types of interferences and PDs are injected into the GIS in two positions and measured in multiple mounting holes. The results show that all four approaches can precisely calculate the characteristic impedance in a matched testbench. In the full-scale GIS, these approaches show more deviation, with the peak approach being the most accurate. A practical application of the method is demonstrated using a calibrator in the full-scale GIS. The proposed method contributes to a more reliable PD monitoring system for HVDC/AC GIS and allows better maintenance planning, reducing unnecessary costs, notably for offshore substations.@en

This paper introduces a directional coupler for partial discharge (PD) measurements in gas-insulated substations (GIS). The sensor comprises a combination of magnetic and electric couplers, effectively segregating forward and backward pulses to enhance PD charge estimation and defect location. The sensor's design was supported with finite element method simulations and measurements conducted in a transverse electromagnetic test bench. Comparative analyses were performed against independent magnetic and electric couplers. The charge estimation and the directional coupler's directivity were evaluated in both the test bench and a full-scale GIS with different PD defects. Initially, the combined magnetic and the electric couplers exhibited undesired interactions, prompting corrective measures. Subsequent adjustments included changes to the electric coupler material and modifications to the magnetic coupler construction. The resulting high-voltage directional coupler performed better than the separated couplers in a GIS with discontinuities. This partial discharge sensor emerges as a candidate for future SF₆-free alternative GIS.

@en

This paper comprehensively reviews several techniques that address the static and dynamic voltage balancing of series-connected MOSFETs. The effectiveness of these techniques was validated through simulations and experiments. Dynamic voltage-balancing techniques include gate signal delay adjustment methods, passive snubbers, passive clamping circuits, and hybrid solutions. Based on the experimental results, the advantages and disadvantages of each technique are investigated. Combining the gate-balancing core method with an RC snubber, which has proven both technically and commercially attractive, provides a robust solution. If the components are sorted and binned, voltage-balancing techniques may not be necessary, further enhancing the commercial viability of series-connected MOSFETs. An investigation of gate driver topologies yields one crucial conclusion: magnetically isolated gate drivers offer a simple and cost-effective solution for high-frequency (HF) applications (2.5–50 kHz) above 8 kV with an increased number of series devices. Below 8 kV, it is advantageous to move the isolation barrier from the gate drive IC to an optocoupler and isolated supply, allowing for a simple design with commercially available components.@en

More and more printed circuit boards (PCBs) will be used in electric aircraft to achieve higher power density of the on-board electric system, while PCBs in aircraft are more likely to generate partial discharges (PDs) due to external factors such as compact structure and low air pressure. Therefore, this paper proposes a fluorescent fiber-based method for detecting and evaluating PDs on PCBs. The detection method is effectively immune against the presence of the electromagnetic, acoustic and vibration interference. Based on the optical detection, the evolution regularities of PCB surface appearance changes, optical PRPD patterns and optical pulses during the aging process of PCB under different air pressure are analyzed in this paper. Then, 12 assessment features are extracted for the PD aging process, and the contribution of these 12 features to the severity assessment at different air pressures is obtained using the minimal-redundancy-maximal-relevance (mRMR) algorithm. Finally, different numbers of PD features are tested for PD severity assessment by the SVM algorithm. The evaluation results show that the severity assessment method proposed in this paper can achieve an assessment accuracy of at least 91.1% and up to 94.4% under all three air pressures, which has good application and guidance value.

@en

More electric aircraft (MEA) is an important direction for future aircraft development. The printed circuit boards (PCB) of power electronics equipment in MEA operates in a complex environment of low air pressure, square wave voltage, compact layout and strong electromagnetic interference, which makes the PCB more prone to partial discharge (PD). However, the effective detection method and related discharge characteristics for PCB PD under square wave voltage are still unclear. Therefore, this paper proposes a PCB PD detection method based on fluorescent optical fiber, which has good anti-electromagnetic interference ability. The PD characteristics of the PCB with three typical structures under three air pressures are studied, including PD non-breakdown characteristics, changes in optical pulse amplitude and pulse repetition rate during PD aging, PD breakdown path analysis and PCB surface electric field simulation. The analysis shows that air pressure, space charge and PCB surface flatness all have important influences on the PD of PCB under square wave voltage. It provides important theoretical support for the insulation protection design and fault diagnosis of PCB for MEA in the future.@en

This article proposes a new configuration of a modular multilevel converter (MMC) and a Marx generator to generate fast-rising impulse waveforms. This new configuration improves the capabilities of the MMC-based high voltage arbitrary wave shape generator to generate fast-rising impulse since the MMC topology faces many inherent limitations. Similar to the conventional superimposed circuit of the ac transformer or dc rectifier circuit with the Marx generator, three hybrid circuits of MMC and the Marx generator are introduced, where the most optimal choice is made considering the practical aspects of testing, such as the size, cost, and preparation time. Then, a detailed analytical study is performed on the Marx generator circuit and the MMC circuit, and both circuits are coupled together to deliver a complete guideline on choosing various system parameters when the impulse wave shape and the load capacitor are given. The concept of this new hybrid configuration is demonstrated with a scaled-down prototype where the impulse with a rise time of 1 μs is superimposed on different arbitrary wave shapes. Similarly, the MATLAB-Simulink simulation model validates the proposed configuration for a 200, k V dc link voltage and 67 submodules with the desired impulse performance.

@en

Litz wires, which are utilized to suppress eddy current, often have complex structures. This paper presents a partial element equivalent circuit (PEEC)-based 3D model for Litz wires with round conductor. The model accounts for both transverse and longitudinal magnetic fields. The discretization of the Litz wire is based on cylindrical elements resulting in a reduced number of elements. Cylindrical element analysis is based on a 2D analytical method. The proposed model is compared with 3D FEM, which shows the model has good accuracy and fast computational speed. It is promising to facilitate Litz wires optimization.

@en

To test high-voltage (HV) equipment with increasingly complex transients obtained from various power system studies, this article demonstrates a hardware implementation of a medium-voltage (MV) submodule (SM) to be used in a modular multilevel converter (MMC)-based HV arbitrary wave shape generator (AWG). The MV SM is scalable with its own onboard auxiliary power supply (APS), and it is constructed by connecting three full-bridge SMs in series from the commercially available component. The designed MV SM can be operated for a wide voltage range of 0.8-2.7 kV to incorporate different test objects ranging from HV insulation material to MV equipment and generate a wide output range of 0.12-1.2 kV. Considering the hardware nonidealities in the APS, gate driver, and switches, the series operation of three SMs is ensured using an arm energy controller. Based on the current-based model of APS, SM capacitance design criteria are updated for variable-frequency output waveform, and the minimum dc-link voltage is calculated for the proper start-up of this scalable MMC module. Apart from the variable voltage per SM, the HV AWG application poses different conditions, such as a low value of SM capacitance value and the HV dc sources with a current rating of a few tens of milliamperes. Hence, this article proposes exclusive design guidelines for the proper start-up, steady-state, and shutdown operation of the MMC-based AWG. In addition, this article dives deeper analytically into the soft start-up algorithm to understand its working principle and to design the average charging current within the limit for any number of SMs of the arm. In the end, their performance is showcased with a single MV SM per arm, operating at a different voltage (0.8-2.7 kV) and frequency levels (1-600 Hz) and generating different wave shapes, such as triangular, sinusoidal with different harmonics, and pulse waveforms. In addition, the fault ride-through capability is verified for the MMC-based HV AWG.

@en

In order to damp the resonance in the MMC-based Arbitrary Wave shape Generator (AWG) used for high voltage testing, an active damping control methodology is proposed in this paper instead of the passive damping with an arm resistor. It is vital to ensure the system’s stability when such an active damping closed loop control is implemented. Consequently, optimal parameters of a PI controller are designed by analyzing the stability margins of the involved transfer function using Bode-Plots. The performance of the designed active damping control methodology and the PI controller have been demonstrated with a 50 Hz sinusoidal waveform and arbitrary waveforms such as triangular, trapezoidal, and complex waveforms in MATLAB-Simulink. These results proves that the output voltage can track the reference without any reasonable error and does not contain any resonant frequency. Additionally, the Total Harmonic Distortion (THD) of the sinusoidal waveform and other arbitrary waveforms is less than 1% with the Phase Shift Carrier (PSC) modulation technique.@en

Magnetic components are essential parts in many power electronic applications. Their characteristics deeply impact the performances of the applications. This article proposed a 2-D calculation method for frequency-dependent winding losses and leakage inductance of magnetic components of round conductors. The method does not have any limitations on the winding arrangement and considers the impact of magnetic cores and air gaps. The method is compared with several analytical methods and the 2-D finite-element method (FEM). Measurements and 3-D FEM are also used to validate the method. The results show that the proposed method generally has more than ten times shorter computational time than 2-D FEM and comparable accuracy, which can speed up the magnetic component design.

@en

A Modular Multilevel Converter (MMC)-based Arbitrary Wave shape Generator (AWG) for High Voltage (HV) testing faces challenges in the control hardware to generate kHz-range high-frequency waveforms. Real Time Simulators (RTS) provide a simple way to implement the control of the MMC-based AWG in the FPGA. One of the commercially available RTS named Typhoon HIL is found to satisfy the small simulation step requirement such as minimum of 200 ns for generating kHz-range high-frequency waveforms. The performance of Typhoon HIL device is demonstrated with a scaled-down prototype of MMC-based AWG where sinusoidal and other arbitrary waveforms are generated up to 5kHz with a THD less than 5 %.@en

Litz wire, which is used to suppress eddy current, always have complex structure. Solving its 3-D finite element model (FEM) requires high computational resources. This article presents a 2.5-D loss calculation method for round Litz wires, which do not need mesh. One pitch of Litz wire is set as an object. The exact structure is constructed by a recursive method and then is sliced into several sections per pitch. Each section is represented by a cross section area. Two-dimensional problems are solved based on an analytical method, which is based on magnetic vector potentials in quasi magneto-statics situation. One pitch of the Litz wire is approximately represented by the summation of 2-D problems. The proposed method is compared with 3-D FEM results, which shows the proposed method has good accuracy and fast computational speed.

@en

One of the main difficulties in measuring partial discharges (PD) in gas-insulated substations (GIS) is the overlapping of pulses at the sensor's location, which distorts the pulse resolution and the charge estimation. This research presents a new method called “synergy,” which identifies and suppresses reflections using magnetic and electric antennas in the very-high frequency range. By scaling the antennas’ outputs and adding them, it is possible to segregate forward and backward pulses. Additionally, by multiplying the electric and magnetic signals, the power flow of the pulses is obtained, which identifies the propagation direction and the location of discontinuities in the transmission path. The synergy method is evaluated in three scenarios: a fully matched test bench using a calibrated pulse, a full-scale GIS using a calibrated pulse, and a full-scale GIS using a PD defect. The results showed that the pulse reflections can be eliminated from the incident pulse, improving the charge calculation when the pulses overlap. The output of this research represents an improvement for PD monitoring in GIS, exhibiting a tool for better defect localization, pulse wave shape construction, charge estimation, and possible interference rejection.

@en

Green hydrogen production uses renewable energies to energise the electrolysers for hydrogen production. The present paper compares possible solutions and configurations of a medium-frequency transformer (MFT) as part of a solid-state transformer (SST) in green hydrogen production applications. The single-phase and three-phase MFTs are compared and it is shown that a Yd three-phase MFT is the optimum choice for applications that require high power delivery and step-down of the voltage. A summary of previous works about MFT is also provided. Three-phase SST based on modular multilevel converters (MMC) is then described and various cases are investigated to obtain the optimum operational frequency. A 25 MVA, 400 Hz, 25.4 kV / 560V oil-immersed MFT design is presented and is shown that the proposed 400 Hz transformer saves 69% of the active parts' weight compared to a conventional line-frequency transformer (LFT).@en

In this paper, air discharges for different frequencies are tested in a point-plane geometry with different air gaps. The stress frequencies vary between 50 Hz to 5 kHz, and air gaps vary from 2.5mm to 10mm. It is observed that the partial discharge inception voltage of the positive corona increases with the increase of frequency, while the inception voltage of the negative corona stays nearly the same. The breakdown voltage increases with the increase of frequency in our test set, and breakdowns happen during negative half-cycle, especially at 5kHz, which is supposed to be caused by the space charges.@en

Penetration of power electronics in the grid has produced a new species of stresses, characterized by fast-rising pulsed waveforms with microsecond rise times repeating at several tens of kilohertz. Analyzing their impact on existing and future insulation systems requires pulse modulators, most often with pulse transformers (PTs), to perform aging and breakdown tests. PT design for klystron loads has been studied extensively albeit for either low repetition rates or short pulse durations. However, capacitive dielectric loads impose additional complex constraints on optimizing leakage ( ${L}_{\sigma }$ ) and parasitic capacitance ( ${C}_{d}$ ) in order to minimize rise time ( ${T}_{r}$ ) and overshoot ( $V_{\text {pk}}$ ). Ensuring consistent output pulse shape is crucial since breakdown is sensitive to voltage magnitude. This article discusses these challenges through the design procedure of a modulator prototype capable of producing bipolar pulses up to 14 kV with rise times $ < 2 ~\mu \text{s}$ at frequencies between 10 and 50 kHz. Major challenges, especially core selection, winding design, PT parasitic optimization, breakdown detection, and failure modes, are highlighted. A new PQR equation is derived to model modulators with capacitive loads. Finally, the output pulses are applied across oil-impregnated paper samples to generate statistics on insulation breakdown strength and lifetime at 10 and 50 kHz. Results illustrate a reduction in lifetime and breakdown strength at 50 kHz. This is possibly due to the nonhomogenous distribution of dielectric losses within the oil-paper leading to local hotspots and eventual thermal breakdown. Furthermore, a critical field ${F}_{c} = {21}$ kV/mm is found below which the slope of the lifeline decreases dramatically, thereby indicating a shift in the aging mechanism. Potential reasons for this phenomenon are also discussed.

@en

Partial discharge (PD) measurements in gasinsulated substations (GIS) are tested according to the standard IEC 60270. This “conventional” PD test method applies to electrically small devices. The equipment size increases the resonance, and attenuation, contributing to the total uncertainty. Additionally, when an ultra-high frequency (UHF) sensor is used as a coupling capacitor, the calibrator and PD pulse duration difference increase the measurement uncertainty. In this paper, the IEC method, using an external capacitor coupler and a UHF sensor, is simulated and tested in a full-scale GIS. The results show the uncertainty dependency with the IEC 60270 filter bandwidth. With proper measures, the UHF sensor correlates with the external coupling capacitor, resulting in a reasonable charge estimation for a 25-meter-long GIS. Knowing the calibration limits is critical to estimate the PD charge uncertainty.@en

In this article, an approach combining semi-empirical equations and the method of images is proposed for round conductor layer windings with un-gapped core. The new equation for proximity effect can convert the constant field strength from the magneto-motive force (MMF) across the core window into a frequency-dependent uniform background magnetic field strength, which can take partly the interaction between conductors into account. Geometric factors are introduced by fitting the finite element method (FEM) results to improve the accuracy. The method of images is used to calculate the field strength in order to counteract the impact of the 2-D edge effect. The new method is compared with the 2-D FEM, analytical methods, and is also validated by measurements with EE core transformers. The proposed method shows good accuracy (< 10% error) compared with 2-D FEM for both high and low porosity factor windings. Therefore, it can handle more winding configurations than other 1-D analytical methods.

@en

In the future, series-connected SiC MOSFETs will become widely used in power-electronic-based medium and high voltage (HV) applications such as modular multilevel converters (MMCs). Balanced voltage sharing among the SiC MOSFET string is hard to be achieved due to possible deviation on MOSFET switching delay. In this paper, two types of gate signal delay adjustment methods (gate balancing core and improved RC snubber method) are presented to solve the unbalanced voltage sharing caused by MOSFET turn-off delay differences. The methods are validated with laboratory experiments performed on low-voltage prototypes and a performance comparison of these two approaches is given. Both methods significantly improve the drain-source voltage sharing, but the gate balancing core method is most suitable for HV and high-frequency applications.@en