Objective: The effectiveness of filtering facepiece respirators such as N95 respirators is heavily dependent on the fit. However, there have been limited efforts to discover the size of the gaps in the seal required to compromise filtering facepiece respirator performance, with prior studies estimating this size based on in vitro models. In this study, we measure the size of leak necessary to compromise the fit of N95 respirators. Methods: Two methods were used to create a gap of specific dimensions. A set of 3D-printed resin spacers and hollow steel rods were used to generate gaps in N95 respirators while worn on 2 participants. Occupational Safety and Health Administration (OSHA) quantitative fit testing methods were used to quantify mask performance with gaps between 0.4 and 2.9-mm diameters. Results: Gap size was regressed against fit factor, showing that overall, the minimum gap size to compromise N95 performance was between 1.5 mm2 and 3 mm2. Conclusions: These findings suggest the fit of a N95 respirator is compromised by gaps that may be difficult to visually detect. The study also adds to the body of evidence supporting the routine use of quantitative fit testing to ensure that masks are well-fitting.

Introduction During the course of the COVID-19 pandemic, there have been suggestions that various techniques could be employed to improve the fit and, therefore, the effectiveness of face masks. It is well recognized that improving fit tends to improve mask effectiveness, but whether these fit modifiers are reliable remains unexplored. In this study, we assess a range of common "fit hacks"to determine their ability to improve mask performance. Methods Between July and September 2020, qualitative fit testing was performed in an indoor living space. We used quantitative fit testing to assess the fit of both surgical masks and KN95 masks, with and without 'fit hacks', on four participants. Seven fit hacks were evaluated to assess impact on fit. Additionally, one participant applied each fit hack multiple times to assess how reliable hacks were when reapplied. A convenience of four participants took part in the study, three females and one male with a head circumference range of 54 to 60 centimetres. Results and discussion The use of pantyhose, tape, and rubber bands were effective for most participants. A pantyhose overlayer was observed to be the most effective hack. High degrees of variation were noted between participants. However, little variation was noted within participants, with hacks generally showing similar benefit each time they were applied on a single participant. An inspection of the fit hacks once applied showed that individual facial features may have a significant impact on fit, especially the nose bridge. Conclusions Fit hacks can be used to effectively improve the fit of surgical and KN95 masks, enhancing the protection provided to the wearer. However, many of the most effective hacks are very uncomfortable and unlikely to be tolerated for extended periods of time. The development of effective fit-improvement solutions remains a critical issue in need of further development.

Objective: Qualitative fit testing is a popular method of ensuring the fit of sealing face masks such as N95 and FFP3 masks. Increased demand due to the coronavirus disease 2019 (COVID-19) pandemic has led to shortages in testing equipment and has forced many institutions to abandon fit testing. Three key materials are required for qualitative fit testing: the test solution, nebulizer, and testing hood. Accessible alternatives to the testing solution have been studied. This exploratory qualitative study evaluates alternatives to the nebulizer and hoods for performing qualitative fit testing. Methods: Four devices were trialed to replace the test kit nebulizer. Two enclosures were tested for their ability to replace the test hood. Three researchers evaluated promising replacements under multiple mask fit conditions to assess functionality and accuracy. Results: The aroma diffuser and smaller enclosures allowed participants to perform qualitative fit tests quickly and with high accuracy. Conclusions: Aroma diffusers show significant promise in their ability to allow individuals to quickly, easily, and inexpensively perform qualitative fit testing. Our findings indicate that aroma diffusers and homemade testing hoods may allow for qualitative fit testing when conventional apparatus is unavailable. Additional research is needed to evaluate the safety and reliability of these devices.

Introduction The COVID-19 pandemic has made well-fitting face masks a critical piece of protective equipment for healthcare workers and civilians. While the importance of wearing face masks has been acknowledged, there remains a lack of understanding about the role of good fit in rendering protective equipment useful. In addition, supply chain constraints have caused some organizations to abandon traditional quantitative or/and qualitative fit testing, and instead, have implemented subjective fit checking. Our study seeks to quantitatively evaluate the level of fit offered by various types of masks, and most importantly, assess the accuracy of implementing fit checks by comparing fit check results to quantitative fit testing results. Methods Seven participants first evaluated N95 and KN95 respirators by performing a fit check. Participants then underwent quantitative fit testing wearing five N95 respirators, a KN95 respirator, a surgical mask, and fabric masks. Results N95 respirators offered higher degrees of protection than the other categories of masks tested; however, it should be noted that most N95 respirators failed to fit the participants adequately. Fit check responses had poor correlation with quantitative fit factor scores. KN95, surgical, and fabric masks achieved low fit factor scores, with little protective difference recorded between respiratory protection options. In addition, small facial differences were observed to have a significant impact on quantitative fit. Conclusion Fit is critical to the level of protection offered by respirators. For an N95 respirator to provide the promised protection, it must fit the participant. Performing a fit check via NHS selfassessment guidelines was an unreliable way of determining fit.

OBJECTIVE: We examined the ability of fabrics which might be used to create home-made face masks to filter out ultrafine (0.02-0.1 µm) particles at the velocity of adult human coughing. METHODS: Twenty commonly available fabrics and materials were evaluated for their ability to reduce air concentrations of ultrafine particles at coughing face velocities. Further assessment was made on the filtration ability of selected fabrics while damp and of fabric combinations which might be used to construct home-made masks. RESULTS: Single fabric layers blocked a range of ultrafine particles. When fabrics were layered, a higher percentage of ultrafine particles were filtered. The average filtration efficiency of single layer fabrics and of layered combination was found to be 35% and 45%, respectively. Non-woven fusible interfacing, when combined with other fabrics, could add up to 11% additional filtration efficiency. However, fabric and fabric combinations were more difficult to breathe through than N95 masks. CONCLUSIONS: The current coronavirus pandemic has left many communities without access to N95 face masks. Our findings suggest that face masks made from layered common fabric can help filter ultrafine particles and provide some protection for the wearer when commercial face masks are unavailable.