This study uses the acoustic emission structural health monitoring method to identify fracture mechanisms in composite bonded joints when varying the substrate stacking sequence. Quasi-static mode I loading tests were performed on secondary adhesively bonded multidirectional composite substrates (0, 90, 45, −45, 60 and −60° fibre orientations). An unsupervised artificial neural network combined with the visual fracture evaluation of the specimens and the Morlet continuous wavelet transform was used to cluster and give the acoustic emission signals a physical meaning. Different fracture mechanisms could be identified within the adhesive layer (i.e., cohesive failure) and in the composite substrates, including non-visible damage mechanisms (matrix micro-cracking, fibre/matrix debonding, fibre pull-out and fibre breakage). Using the Morlet continuous wavelet transform, it was possible to recognise that the highest peak frequency does not always represent the most relevant signature of the fracture mechanism. Moreover, multiple peak frequencies can be associated with multiple fracture mechanisms, such as the fibre pull-out that occurs in the combination of matrix cracking and fibre breakage. Furthermore, no differences were observed in mode I loading conditions between the acoustic emission signatures from the cohesive failure in the adhesive layer and the matrix cracking within the composite substrate. The findings of this study present a great opportunity to gain more insight into the fracture behaviour of polymer materials and fibre-reinforced polymer materials and to improve the quality of adhesively bonded joints.

@en

Understanding the relationship between the sensors’ outputs and the damage evolution within the joints is becoming increasingly crucial to improving structural health monitoring systems and collecting data to improve the joint’s design. Therefore, a study of the acoustic emission method associated with visual fracture evaluation was proposed to give insights into the toughening of composite bonded joints and better understand the relationship between the acoustic emission features and the damage mechanism involved. Thus, two different layups were proposed for the substrates: [0]8 and [0/902/0]S. In addition, a toughened epoxy adhesive with an embedded carrier (AF163-2k) was used to bond the substrates. Five specimens of each stacking sequence were tested under quasi-static mode I loading conditions. A travelling microscope and a regular digital camera were used on the lateral sides of the specimens to track the crack propagation paths. One piezoelectric sensor linked to the AMSY-6 Vallen system was used to assess the acoustic emission features produced within the joints during the tests. Unsupervised machine learning algorithms based on artificial neural networks and the Morlet continuous wavelet transformation were used to pattern recognition of the acoustic emission data. Self-organising maps, together with k-means algorithms, were used for data clustering. Following that, the acoustic emission features of each cluster were associated with the insights obtained from the crack propagation images. Finally, it was observed that the different layups triggered simultaneous toughening mechanisms. The combination of the acoustic emission and the visual evaluation was crucial for a deeper understanding of the underlying phenomena.@en

Aiming to increase damage tolerance of adhesively bonded joints, this work explores the influence of CFRP layup of the adherends on the crack onset and crack propagation of composite bonded joints under mode I loading. Quasi-static Double Cantilever Beam tests were performed using four different CFRP layups bonded with two adhesives. Parallel to the experimental program, finite element analyses were performed to aid in understanding and identifying the various damage mechanisms in each specimen type. The results show that the CFRP layup and adhesive fracture toughness significantly influence the joint fracture phenomena at crack onset and further crack propagation. An enhancement of the joint's mode I fracture toughness values at crack onset was observed in the specimens where a crack competition between the propagation within the bondline and the composite's layers was triggered. During crack propagation, the fracture toughness of the joint increases at crack deflections between the different plies of the CFRP layup until reaching the 0° ply, where sudden delamination occurs. It has been shown that CFRP layup tailoring is a promising toughening method that, when carefully designed, has the potential to increase the maximum effective fracture toughness up to 100% when compared to pure cohesive failure.

@en

Delamination growth in fibre reinforced polymer composites is generally evaluated with experiments that have been standardized for quasi-static load conditions. These tests characterize unidirectional delamination growth in mode I (DCB), mode II (ELS or ENF) of mixed mode conditions (MMB). However, little attention is paid in literature to the applicability of these tests to in-service delamination problems that are generally characterized by planar delamination growth. In this study, the relation between planar delamination growth, induced by transverse quasi-static indentation loading, and these unidirectional delamination tests was investigated. To that aim, prior planar delamination growth tests reported in literature, performed at EPFL, were analysed to identify up to what extent this planar growth could be correlated to the concepts of strain energy release and strain energy density. Once this appeared to successful, an experimental setup was designed to measure the delamination boundary during the transverse indentation loading of planar delamination specimens made of nontransparent carbon fibre reinforced polymer composites. With that set-up, quasi-static and fatigue planar delamination growth experiments were performed, and delamination contours could be successfully captured. While the quasi-static tests revealed limited growth, evaluation with numerical simulations revealed that the indentation force required to extend the delamination quasi-statically would cause damage to the specimen. This is attributed to the increasing length of the delamination contour when delaminations expand, which is not the case with standard unidirectional specimen. With the fatigue tests, however, delamination growth was achieved, but interestingly enough two phases were observed; first the delamination propagated in a planar fashion, while at some point in time work did not exceed an apparent threshold. Instead of no growth, however, the delamination still increased but then in a transverse manner. What makes this study of particular interest, is that the strain energy density as criterion could capture the strain energy offered (work) along the entire delamination contour, while the strain energy release rate described the resistance to delamination growth. This latter observation is in agreement with the original concept employed by Griffith when he formulated the basis of linear elastic fracture mechanics. This presentation present the experiments performed, the analysis of results, and will conclude with a proposal how to relate standard unidirectional tests to planar growth, considering that these standard tests contain little to no information on transverse phenomena with respect to strain energy density (work) and strain energy release (dissipation). @en