Person | TU Delft Repository

T. J.J. Maal

2 records found

Authored

Quality of life of patients with 3D-printed arm prostheses in a rural area of Sierra Leone

Journal article (2021) - A. J. Sterkenburg, M. van der Stelt, A. R. Koroma, M. D. Van Gaalen, M. J. Van der Pols, M. P. Grobusch, M. P. Grobusch, Cornelis H. Slump, T. J.J. Maal, L. Brouwers, L. Brouwers

Introduction: In Sierra Leone, access to prostheses is limited due to absence of practical knowledge, materials, trained staff, and high cost. This paper investigates the impact of a 3D printed prosthesis on the health-related quality of life (HRQoL) in prosthesis recipients. Methods: Patients with upper extremity amputations were included in this case study from December 2018 until July 2019. Data on the HRQoL was gathered until April 2020 in Masanga Hospital, central rural Sierra Leone. At two follow-up moments the HRQoL was assessed by applying the standard EQ-5D-5L questionnaire. These two follow-up moments varied between one week and just over a year after receiving the prosthesis. A second patient questionnaire was used to assess prosthesis satisfaction. Results: Seven patients were included. The results of the EQ-5D-5L questionnaire show no deterioration of the HRQoL in any patient and the overall HRQoL increased by almost 20% compared to the null measurement. One patient was lost to follow up after the first re-visit. The responses to the second questionnaire indicated that patients are satisfied with the prosthesis and use it in various situations. Patients often mentioned they feel more included in society when wearing the prosthesis. One patient says wearing the prosthesis helped in accepting the amputation. As a result, enough self-confidence was experienced without the prosthesis and the patients stopped wearing the prosthesis. Discussion: The overall HRQoL in patients wearing a 3D-printed prosthesis increases compared to not wearing one. Assessing the HRQoL at regular intervals is important for the long-term follow-up and to safeguard sustainability and long-term success of this project. Nevertheless, defining the HRQoL is challenging due to cultural differences and misunderstandings. Therefore, the use of alternative questionnaires to define the HRQoL should be investigated. To improve and warrant long-term success, identifying long-term problems is important, and the second questionnaire accounts for this need.

@en

Contributed

Validation of 3D-printed guidance systems for genioplasties in orthognathic surgery

A retrospective validation study & preparation for a multicenter intervention study

Master thesis (2020) - J.F. Sabelis, J. Dankelman, A.G. Becking, T. J.J. Maal, T.C.T. van Riet, R. Schreurs

A chin deformity does not rarely accompany dentofacial deformities. A correction of the chin (genioplasty) is sometimes indicated in addition to orthognath ...

A chin deformity does not rarely accompany dentofacial deformities. A correction of the chin (genioplasty) is sometimes indicated in addition to orthognathic surgery. Computer-assisted surgery allows virtual planning in orthognathic surgery in three-dimensions (3D). The virtually planned movements will be transferred to the patients through 3D-printed devices, such as occlusal splints for the maxillomandibular complex. Computer-assisted surgery also enables the evaluation and quantification of the surgical result in 3D, through comparison of the virtual surgical planning and postoperative imaging. The OrthoGnathicAnalyser is a software tool that enables semi-automatic quantification of the surgical result for repositioning of the mandible, maxilla and rami in orthognathic surgery. The goal of this master thesis was to validate the application of 3D-printed guidance systems for the execution of genioplasties in the context of orthognathic surgery with a new version of OrthoGnathicAnalyser.

A new version of OrthoGnathicAnalyser was developed, to allow for analysis of the genioplasty. The effect of two factors (calculation of chin analysis and registration technique) on the precision and accuracy has been evaluated. This has led to two important conclusions which are implemented in the software: 1) The difference between the postoperative chin and the planned chin with respect to the realized mandible (instead of the planned mandible) should be calculated, to isolate the mandibular positioning error from the chin error. 2) Surface-based matching resulted in more accurate pitch values and was therefore implemented in the newest version.

To present and validate the newly developed software, a multicenter study was executed. A total of 25 patients were included in the study. The inter-observer and intra-observer reliability were evaluated. It was concluded that the reported results demonstrated an excellent reproducibility (ICC >0.92) of the quantification of the skeletal movements between two image sets by the OrthoGnathicAnalyser 2.0. By implementing the chin analysis in the software tool, the complete orthognathic surgery result could be quantified and compared to the virtual plan. The results of this study will be submitted to a scientific journal.

To validate the 3D-printed guidance system for genioplasties, a multicenter randomized controlled intervention study was initiated. To acquire ethical approval of the local ethics committee, extensive preparations were required. Approval to start the study has been acquired within this graduation project and patient inclusion will start when COVID-19 circumstances allow continuation of clinical studies and regular patient care.

To validate 3D-printed guidance systems for the execution of genioplasties different projects were undertaken. A new version of the OrthoGnathicAnalyser was developed and validated. Advantageous of the OrthoGnathicAnalyser 2.0 was the implementation of the chin analysis, independence on any planning software and reduced manual input. Possible improvements were the implementation of automatic 3D landmarking and adapting the voxel-based matching algorithm to allow exclusion of the fixation material. A multicenter intervention study to evaluate the accuracy of the 3D-printed guidance system for genioplasties with the newly developed software was initiated. This study will enable a definitive conclusion about the effect of the 3D-printed guidance system on the accuracy of chin repositioning.