In this study, the impact of different vibrational modes on the fluidization characteristics of cohesive micro- and nano-silica powder was examined. Fractional pressure drop, bed expansion measurements, and X-ray imaging were utilized to characterize the fluidization quality. The densities of the emulsion phase at the top and bottom of the column were quantified and compared, providing insights into the solid distribution within the fluidized bed. In the absence of vibration, neither powder could be fluidized within the considered range of superficial gas velocities. Vertical vibration was found to initiate fluidization for both powders. In contrast, elliptical vibration failed to overcome the channelling behavior when fluidizing the micro-powder. For nano-powder, combined channelling and powder compaction occurred when the bed was subjected to elliptical vibration. For the micro-powder, it was observed that bed homogeneity was independent of vertical vibration intensity but improved with increasing superficial gas velocity. For nano-powder, intensifying vertical vibration led to segregation, likely due to agglomerate densification. Furthermore, fractional pressure drop measurements proved to be a strong tool in assessing fluidization quality, providing insights that could not be attained by conventional indicators.

Vibro-assisted fluidization of cohesive micro-silica has been studied by means of X-ray imaging, pressure drop measurements, and off-line determination of the agglomerate size. Pressure drop and bed height development could be explained by observable phenomena taking place in the bed; slugging, channeling, fluidization or densification. It was observed that channeling is the main cause of poor fluidization of the micro-silica, resulting in poor gas-solid contact and little internal mixing. Improvement in fluidization upon starting the mechanical vibration was achieved by disrupting the channels. Agglomerate sizes were found to not significantly change during experiments.

Stirring has been recognized in the literature as a promising technique for facilitating fluidization of cohesive powders, via inputting additional energy to counteract interparticle forces. However, the influence of operating conditions and stirrer configurations on flow behavior remains largely unknown, which impedes the practical implementation of stirred fluidization. Utilizing X-ray imaging, this research demonstrates that stirring enhances fluidization in cohesive micron-silica powder (Sauter mean diameter [Formula presented]) by collapsing the powder packing structure, and transitioning channeling beds into bubbling states. Comb-like configurations featuring fewer stirrers and blades, placed in the bottom region, have shown to be highly effective. Excessive stirring can lead to air pockets and a compacted phase of particles on the column walls, undermining the interaction between particles and stirrers. Additionally, the experiments show that maximizing the sweeping coverage, employing complex asymmetrical configurations, and avoiding tortuous gas pathways are preferable.

In this study, we investigated the wettability and agglomeration characteristics of polymer microspheres coated with low-temperature deposited SiO₂ in a fluidized bed atomic layer deposition (ALD) setup. Surface characterization revealed the presence of a significant amount of deposited Si-OH groups within the first cycles. A drastic decrease in agglomerate size, water contact angle (WCA), and droplet absorption time of the powder was observed when coating was applied. Furthermore, we observed an increase in the amount of Si-OH present on the particle surface with increasing coating cycles, while no significant improvement in water affinity was found after the first coating cycles. Our findings suggest that surface coverage is the primary factor in improving the colloid stability of particles, coated at low temperatures. The low temperature operation of our system introduced a chemical vapor deposition (CVD) component to our coating process, which allowed full surface coverage to be achieved within the first two coating cycles.

The fluidization of cohesive powders has been extensively researched over the years. When looking at literature on the fluidization of cohesive particles, one will often find papers concerned with only micro- or only nano-sized powders. It is, however, unclear whether they should be treated differently at all. In this paper, we look at differences and similarities between cohesive powders across the size range of several nanometres to 10s of micrometres. Classification of fluidization behaviour based on particle size was found to be troublesome since cohesive powders form agglomerates and using the properties of these agglomerates introduces new problems. When looking at inter-particle forces, it is found that van der Waals forces dominate across the entire size range that is considered. Furthermore, when looking into agglomeration and modelling thereof, it was found that there is a fundamental difference between the size ranges in the way they agglomerate. Where the transition between the types of agglomeration is located is, however, unknown. Finally, how models are made and agglomerate sizes are measured is currently insufficient to accurately predict or measure their sizes consistently.