Bolted connections are one of the key connection configurations in steel structures. The ductile fracture prediction is one of the challenges in the structural integrity evaluating of steel structures. To guarantee the safety of steel bridge in connections, an accurate assessment of the ultimate resistance of high-strength bolts under combined tensile-shear loads is necessary. However, the impacts of various parameters on high-strength bolts under combined tensile-shear loads are not sufficiently analysed in the existing references. Hence, in this paper, the validated mesoscale critical equivalent plastic strain (MCEPS) method is used to evaluate the ultimate resistance of high-strength bolts with different bolt grades, bolt diameters, bolt types, hole clearance, and preload force when the bolts are exposed to combined tensile-shear loading. The simulation results are compared to existing design specifications. Finally, the formula modifications in the existing design standards are proposed based on statistical analysis on numerical parametric results.

@en

The development of numerical simulation for Ultra-high-performance concrete (UHPC) and Ultra-high-performance fiber-reinforced concretes (UHPFRC) is fundamental for the design and construction of related structures. The simplified engineering stress-strain relationship and the input values are necessary in the finite element modeling. Four-linear curves and modified Kent–Park model were proposed to describe the engineering tensile and compressive stress-strain relationship, respectively. An attempt was made to simulate the fracture of UHPC and UHPFRC using concrete damaged plasticity model and element deletion strategies. The predicted tensile and compressive behaviors of UHPC and UHPFRC were successfully validated by the test results in the literature. For a better understanding of the mechanical behavior of UHPC and UHPFRC exposed to biaxial loadings, mixed-mode crack propagation simulation on the double-notched specimens exposed to combined shear-tensile and shear-compressive forces was discussed.

@en

Wire arc additive manufacturing (WAAM) has increasingly attracted attention in the construction sector because of its ability to produce large metallic structural parts in short times. In this paper, Coffin-Manson and Morrow (CMM) equation is employed to compare the fatigue life of WAAM stainless steel with the structural steels S355 and S690. The results showed that the fatigue performance of structural steel is better than the WAAM stainless steel, the fatigue performance vertical to printing direction (WAAM-900) is better than it along the printing direction (WAAM-00). In addition, the fatigue cycle of the transition reversals of structural steel is much less than it of WAAM stainless. With the increasing the fatigue cycle, the maximum density of the strain amplitude ratio is gradually increased to 1.0. The probabilistic parameters of CMM equation were obtained by a stochastic analysis using Latin hypercube sampling strategies. The probabilistic strain-fatigue life behaviour obtained from the constant exponent sampling strategy is higher when compared with the varied exponent sampling strategy for both WAAM stainless and structural steels.

@en

Steel-concrete composite high bridge pier has been applied increasingly in China and around the world. Most applied steel type in the composite piers are H-shaped steel and steel pipe, while seldom research or practice is associated with angle steel. This paper conducted parametric study on the composite column with equal-leg angle steel and aimed to investigate the ultimate load and displacement ductility of the composite columns with different parameters. The parameters include the type of shear connector (stud and perfobond connectors), the type of structural steel (H-shaped steel and angle steel), steel-plate hooping ratio, shear-span ratio, and axial compression ratio. Finite element analysis was conducted for each specimen, which incorporated the concrete confinement effect, as well as the inelastic behavior of concrete, structural steel, and longitudinal and transverse steel bars. The equal-leg angle steel composite column was found to have slightly higher strength and displacement ductility than H-shaped steel composite column. The increase of steel-plate hooping result in larger strength and displacement ductility for the composite column, and the increase of shear-span ratio and axial compression ratio decrease the displacement ductility. Research results suggest stud and perfobond shear connectors should be applied as axial compression ratio being larger than 0.2 and 0.3, respectively. This paper provides reference for research and engineering practice of the concrete encased angle steel composite columns and bridge piers.@en

In this study, flexural behaviors of the pultruded composite laminate were evaluated through experiments and theoretical analysis. Three-point flexural tests were performed for pultruded specimens. The typical failure mode for the longitudinal flexural specimens was local crush on the top surface accompanied with local cracks on the bottom surface at midspan. For the transverse tests, the specimens presented a failure pattern with local cracks initiated and propagated at both the top and bottom sides at the midspan. Theoretical analysis, based on micromechanics and macromechanics, was performed to predict flexural deformation and stress distribution of the pultruded laminate beam. Based on the continuum damage model proposed by the authors, this paper mainly investigates the flexural behavior and failure pattern of pultruded lamination. The theoretical and finite element results agreed well with the test results. The results can provide a reference for the design of the structural pultruded modular systems.@en