AM Hoogstrate | TU Delft Repository

A

AM Hoogstrate

Book chapter (2)

Conference paper (31)

Doctoral thesis (1)

Journal article (22)

Report (1)

57 records found

1

Micromilling of thin ribs with high aspect ratios.

Journal article (2010) - P Li (author), D Zdebski (author), HH Langen (author), AM Hoogstrate (author), JAJ Oosterling (author)

Improving micro-milling technology

Journal article (2010) - RS Blom (author), P Li (author), HH Langen (author), AM Hoogstrate (author), H. Oosterling (author), P.M.J. van den Hof (author), R.H. Munnig Schmidt (author)

Study of the relation between cutting toll conditions and machined surfaces in micro square endmilling

Conference paper (2009) - P Li (author), JAJ Oosterling (author), AM Hoogstrate (author), HH Langen (author), R.H. Munnig Schmidt (author)

A Study of Factors affecting the Performance of Micro Square Endmills in milling of Hardened Tool Steels

Conference paper (2008) - P Li (author), AM Hoogstrate (author), JAJ Oosterling (author), HH Langen (author), R.H. Munnig Schmidt (author)

Experimental validation of micro endmill design for hard milling application

Conference paper (2008) - P Li (author), AM Hoogstrate (author), JAJ Oosterling (author), R.H. Munnig Schmidt (author)

Design of the neck geometry to improve the stiffness of micro endmills

Conference paper (2008) - P Li (author), PM Rozing (author), JAJ Oosterling (author), AM Hoogstrate (author), HH Langen (author), R.H. Munnig Schmidt (author)

Improvement of Micro Endmill Geometry for Micro Hard Milling Application

Conference paper (2008) - P Li (author), JAJ Oosterling (author), AM Hoogstrate (author), HH Langen (author)

Improved Method for the Cutting Coefficients Calculation in Micromilling Force Modeling

Conference paper (2008) - P Li (author), JAJ Oosterling (author), AM Hoogstrate (author), HH Langen (author)

Form Crush Dressing of Diamond Grinding Wheels

Journal article (2008) - J.M. Derkx (author), AM Hoogstrate (author), J.J. Saurwalt (author), B Karpuschewski (author)

Experimental study of the roughness of hardened tool steel Bohler W300 milled by micro square endmills

Conference paper (2008) - P Li (author), AM Hoogstrate (author), JAJ Oosterling (author), HH Langen (author), R.H. Munnig Schmidt (author)

Experimental study of the surface roughness of hardened tool steel bohler w300 milled by micro square endmills

Conference paper (2008) - P Li (author), PX Aristimuno (author), AM Hoogstrate (author), JAJ Oosterling (author), HH Langen (author), R.H. Munnig Schmidt (author)

Momentum Transfer Efficiency in Abrasive Waterjet Cutting

Conference paper (2007) - VN Pi (author), AM Hoogstrate (author)

Cost Calculation for Recycled Abrasives and for Abrasive Selecting in Abrasive Waterjet Machining

Journal article (2007) - VN Pi (author), AM Hoogstrate (author)

Thermal Distortions in the Machining of Small Bores

Journal article (2007) - IV Bana (author), B Karpuschewski (author), J Kundrak (author), AM Hoogstrate (author)

Performance Evaluation of Micromilling of Hardened Tool Steel

Conference paper (2007) - P Li (author), JAJ Oosterling (author), AM Hoogstrate (author)

A method for synchronizing grinding wheel and form roll speed in point crush profiling of grinding wheels

Conference paper (2007) - J.M. Derkx (author), AM Hoogstrate (author), B Karpuschewski (author), J.J. Saurwalt (author)

Cost Optimization of Abrasive Blasting Systems: A New and Effective Way for Using Blasting Nozzles

Journal article (2007) - VN Pi (author), AM Hoogstrate (author)

Indirect Force measurement of Micromilling with an Active Magnetic Bearing spindle

Conference paper (2007) - RS Blom (author), AM Hoogstrate (author), P.M.J. van den Hof (author), HH Langen (author)

Cost Calculation for Abrasive Recycling and for Abrasive Comparing for Abrasive Waterjet (AWJ) Cutting Systems

Conference paper (2006) - VN Pi (author), AM Hoogstrate (author)

Cost Optimization for Multiple-head AWJ Cutting

Conference paper (2006) - AM Hoogstrate (author), VN Pi (author)