Coexistence of lipid domains in cell membranes is associated with vital biological processes. Here, we investigate two such membranes: a multi-component membrane composed of DOPC and DPPC lipids with gel and fluid separated domains, and a single component membrane composed of PMPC lipids forming ripples. We characterize their mechanical properties below their melting point, where ordered and disordered regions coexist, and above their melting point, where they are in fluid phase. To conduct these inquiries, we create lipid bilayers in a microfluidic chip interfaced with a heating system and optical tweezers. The chip features a bubble trap and enables high-throughput formation of planar bilayers. Optical tweezers experiments reveal interfacial hydrodynamics (fluid-slip) and elastic properties (membrane tension and bending rigidity) at various temperatures. For PMPC bilayers, we demonstrate a higher fluid slip at the interface in the fluid-phase compared to the ripple phase, while for the DOPC:DPPC mixture, similar fluid slip is measured below and above the transition point. Membrane tension for both compositions increases after thermal fluidization. Bending rigidity is also measured using the forces required to extend a lipid nanotube pushed out of the freestanding membranes. This novel temperature-controlled microfluidic platform opens numerous possibilities for thermomechanical studies on freestanding planar membranes.@en

Eukaryotes swim with coordinated flagellar (ciliary) beating and steer by fine-tuning the coordination. The model organism for studying flagellate motility, Chlamydomonas reinhardtii, employs synchronous, breaststroke-like flagellar beating to swim, and it modulates the beating amplitudes differentially to steer. This strategy hinges on both inherent flagellar asymmetries (e.g. different response to chemical messengers) and such asymmetries being effectively coordinated in the synchronous beating. In C. reinhardtii, the synchrony of beating is known to be supported by a mechanical connection between flagella; however, how flagellar asymmetries persist in the synchrony remains elusive. For example, it has been speculated for decades that one flagellum leads the beating, as its dynamic properties (i.e. frequency, waveform, etc.) appear to be copied by the other one. In this study, we combine experiments, computations, and modeling efforts to elucidate the roles played by each flagellum in synchronous beating. With a non-invasive technique to selectively load each flagellum, we show that the coordinated beating essentially only responds to load exerted on the cis flagellum; and that such asymmetry in response derives from a unilateral coupling between the two flagella. Our results highlight a distinct role for each flagellum in coordination and have implication for biflagellates’ tactic behaviors.@en

Inspired by biological functions of living systems, researchers have engineered cells as independent functional materials or integrated them within a natural or synthetic matrix to create engineered living materials (ELMs). However, the ‘livingness’ of cells in such materials poses serious drawbacks, such as a short lifespan and the need for cold-chain logistics. Bacterial spores have emerged as a game changer to bypass these shortcomings as a result of their intrinsic dormancy and resistance against harsh conditions. Emerging synthetic biology tools tailored for engineering spores and better understanding of their physical properties have led to novel applications of spore-based materials. Here, we review recent advances in such materials and discuss future challenges for the development of time- and cost-efficient spore-based materials with high performance.

@en

Soft materials are usually defined as materials made of mesoscopic entities, often self-organised, sensitive to thermal fluctuations and to weak perturbations. Archetypal examples are colloids, polymers, amphiphiles, liquid crystals, foams. The importance of soft materials in everyday commodity products, as well as in technological applications, is enormous, and controlling or improving their properties is the focus of many efforts. From a fundamental perspective, the possibility of manipulating soft material properties, by tuning interactions between constituents and by applying external perturbations, gives rise to an almost unlimited variety in physical properties. Together with the relative ease to observe and characterise them, this renders soft matter systems powerful model systems to investigate statistical physics phenomena, many of themrelevant as well to hard condensed matter systems. Understanding the emerging properties from mesoscale constituents still poses enormous challenges, which have stimulated a wealth of new experimental approaches, including the synthesis of new systems with, e.g. tailored self-assembling properties, or novel experimental techniques in imaging, scattering or rheology. Theoretical and
numerical methods, and coarse-grained models, have become central to predict physical propertiesof soft materials, while computational approaches that also use machine learning tools are playing a progressively major role in many investigations. This Roadmap intends to give a broad overview of recent and possible future activities in the field of soft materials, with experts covering various developments and challenges in material synthesis and characterisation, instrumental, simulation and theoretical methods as well as general concepts.@en

Engineered living materials (ELMs) are a novel class of functional materials that typically feature spatial confinement of living components within an inert polymer matrix to recreate biological functions. Understanding the growth and spatial configuration of cellular populations within a matrix is crucial to predicting and improving their responsive potential and functionality. Here, this work investigates the growth, spatial distribution, and photosynthetic productivity of eukaryotic microalga Chlamydomonas reinhardtii (C. reinhardtii) in three-dimensionally shaped hydrogels in dependence of geometry and size. The embedded C. reinhardtii cells photosynthesize and form confined cell clusters, which grow faster when located close to the ELM periphery due to favorable gas exchange and light conditions. Taking advantage of location-specific growth patterns, this work successfully designs and prints photosynthetic ELMs with increased CO₂ capturing rate, featuring high surface to volume ratio. This strategy to control cell growth for higher productivity of ELMs resembles the already established adaptations found in multicellular plant leaves.

@en

Vital biological processes, such as trafficking, sensing, and motility, are facilitated by cellular lipid membranes, which interact mechanically with surrounding fluids. Such lipid membranes are only a few nanometers thick and composed of a liquid crystalline structure known as the lipid bilayer. Here, we introduce an active, noncontact, two-point microrheology technique combining multiple optical tweezers probes with planar freestanding lipid bilayers accessible on both sides. We use the method to quantify both fluid slip close to the bilayer surface and transmission of fluid flow across the structure, and we use numerical simulations to determine the monolayer viscosity and the intermonolayer friction. We find that these physical properties are highly dependent on the molecular structure of the lipids in the bilayer. We compare ordered-phase with liquid disordered-phase lipid bilayers, and we find the ordered-phase bilayers to be 10 to 100 times more viscous but with 100 times less intermonolayer friction. When a local shear is applied by the optical tweezers, the ultralow intermonolayer friction results in full slip of the two leaflets relative to each other and as a consequence, no shear transmission across the membrane. Our study sheds light on the physical principles governing the transfer of shear forces by and through lipid membranes, which underpin cell behavior and homeostasis.

@en

FtsH is a membrane-bound protease that plays a crucial role in proteolytic regulation of many cellular functions. It is universally conserved in bacteria and responsible for the degradation of misfolded or misassembled proteins. A recent study has determined the structure of bacterial FtsH in detergent micelles. To properly study the function of FtsH in a native-like environment, we reconstituted the FtsH complex into lipid nanodiscs. We found that FtsH in membrane scaffold protein (MSP) nanodiscs maintains its native hexameric conformation and is functionally active. We further investigated the effect of the lipid bilayer composition (acyl chain length, saturation, head group charge and size) on FtsH proteolytic activity. We found that the lipid acyl chain length influences AaFtsH activity in nanodiscs, with the greatest activity in a bilayer of di-C18:1 PC. We conclude that MSP nanodiscs are suitable model membranes for further in vitro studies of the FtsH protease complex.

@en

Biofilms are three-dimensional (3D) bacterial communities that exhibit a highly self-organized nature in terms of their composition and complex architecture. Bacteria in biofilms display emergent biological properties, such as resistance to antimicrobials and disinfectants that the individual planktonic cells lack. Bacterial biofilms possess specialized architectural features including unique extracellular matrix compositions and a distinct spatially patterned arrangement of cells and matrix components within the biofilm. It is unclear which of these architectural elements of bacterial biofilms lead to the development of their emergent biological properties. Here, we report a 3D printing-based technique for studying the emergent resistance behaviors of Escherichia coli biofilms as a function of their architecture. Cellulose and curli are the major extracellular-matrix components in E. coli biofilms. We show that 3D-printed biofilms expressing either curli alone or both curli and cellulose in their extracellular matrices show higher resistance to exposure against disinfectants than 3D prints expressing either cellulose alone or no biofilm-matrix components. The 3D-printed biofilms expressing cellulose and/or curli also show thicker anaerobic zones than nonbiofilm-forming E. coli 3D prints. Thus, the matrix composition plays a crucial role in the emergent spatial patterning and biological endurance of 3D-printed biofilms. In contrast, initial spatial distribution of bacterial density or curli-producing cells does not have an effect on biofilm resistance phenotypes. Further, these 3D-printed biofilms could be reversibly attached to different surfaces (bacterial cellulose, glass, and polystyrene) and display resistance to physical distortions by retaining their shape and structure. This physical robustness highlights their potential in applications including bioremediation, protective coatings against pathogens on medical devices, or wastewater treatment, among many others. This new understanding of the emergent behavior of bacterial biofilms could aid in the development of novel engineered living materials using synthetic biology and materials science approaches.

@en

Living materials, which are fabricated by encapsulating living biological cells within a non-living matrix, have gained increasing attention in recent years. Their fabrication in spatially defined patterns that are mechanically robust is essential for their optimal functional performance but is difficult to achieve. Here, a bioprinting technique employing environmentally friendly chemistry to encapsulate microalgae within an alginate hydrogel matrix is reported. The bioprinted photosynthetic structures adopt pre-designed geometries at millimeter-scale resolution. A bacterial cellulose substrate confers exceptional advantages to this living material, including strength, toughness, flexibility, robustness, and retention of physical integrity against extreme physical distortions. The bioprinted materials possess sufficient mechanical strength to be self-standing, and can be detached and reattached onto different surfaces. Bioprinted materials can survive stably for a period of at least 3 days without nutrients, and their life can be further extended by transferring them to a fresh source of nutrients within this timeframe. These bioprints are regenerative, that is, they can be reused and expanded to print additional living materials. The fabrication of the bioprinted living materials can be readily up-scaled (up to ≥70 cm × 20 cm), highlighting their potential product applications including artificial leaves, photosynthetic bio-garments, and adhesive labels.

@en

The swift deformations of flagella and cilia are crucial for locomotion and fluid transport on the micron scale. Most hydrodynamic models of flagellar and ciliary flows assume the zero Reynolds number limit and model the flow using Stokes equations. Recent work has demonstrated that this quasi-steady approximation breaks down at increasing distances from the cilia. Here, we use optical tweezer-based velocimetry to measure the flow velocity with high temporal accuracy, and to reconstruct the entire unsteady flow field around beating cilia. We report both the steady and the unsteady component of the ciliary flow and compare them with the solutions to both the Stokes and the Navier-Stokes equations. Our experimental measurements of the velocity and vorticity fields are in agreement with the numerical solution to the Navier-Stokes equations and show significant differences with the solution to the Stokes equations. We characterize the phase difference between the flow oscillations and the oscillations of the ciliary motion and evidence a significant anisotropic phase lag. We show that this phase lag presents the spatiotemporal characteristics of the unsteady Stokes equations and that the flow field around beating cilia is well represented by the fundamental solution to the unsteady Stokes equations: the oscillet.

@en

Sustainable structural materials with excellent impact-resistance properties are urgently needed but challenging to produce, especially in a scalable fashion and with control over 3D shape. Here, we show that bacterial cellulose (BC) and bacterially precipitated calcium carbonate self-assemble into a layered structure reminiscent of tough biomineralized materials in nature (nacre, bone, dentin). The fabrication method consists of biomineralizing BC to form an organic/inorganic mixed slurry, in which calcium carbonate crystal size is controlled with bacterial poly(γ-glutamic acid) and magnesium ions. This slurry self-assembles into a layered material that combines high toughness and high impact and fire resistance. The rapid fabrication is readily scalable, without involving toxic chemicals. Notably, the biomineralized BC can be repeatedly recycled and molded into any desired 3D shape and size using a simple kitchen blender and sieve. This fully biodegradable composite is well suited for use as a component in daily life, including furniture, helmets, and protective garments.

@en

Natural materials, such as nacre and silk, exhibit both high strength and toughness due to their hierarchical structures highly organized at the nano-, micro-, and macroscales. Bacterial cellulose (BC) presents a hierarchical fibril structure at the nanoscale. At the microscale, however, BC nanofibers are distributed randomly. Here, BC self-Assembles into a highly organized spiral honeycomb microstructure giving rise to a high tensile strength (315 MPa) and a high toughness value (17.8 MJ m-3), with pull-out and de-spiral morphologies observed during failure. Both experiments and finite-element simulations indicate improved mechanical properties resulting from the honeycomb structure. The mild fabrication process consists of an in situ fermentation step utilizing poly(vinyl alcohol), followed by a post-Treatment including freezing-Thawing and boiling. This simple self-Assembly production process is highly scalable, does not require any toxic chemicals, and enables the fabrication of light, strong, and tough hierarchical composite materials with tunable shape and size.

@en

Bioinspired bacterial cellulose (BC) composites are next-generation renewable materials that exhibit promising industrial applications. However, large-scale production of inorganic/organic BC composites by in situ fermentation remains difficult. The methods based on BC mechanical disintegration impair the mechanical property of dried BC films, while the static in situ fermentation methods fail to incorporate inorganic particles within the BC network because of the limited diffusion ability. Furthermore, the addition of other components in the fermentation medium significantly interferes with the production of BC. Here, a tough BC composite with a layered structure reminiscent of the tough materials found in nature (e.g., nacre, dentin, and bone) is prepared using a semistatic in situ fermentation method. The bacterially produced biopolymer γ-poly(glutamic acid) (PGA), together with graphene oxide (GO), is introduced into the BC fermentation medium. The resulting dried BC-GO-PGA composite film shows high toughness (36 MJ m-3), which makes it one of the toughest BC composite film reported. In traditional in situ fermentation methods, the addition of a second component significantly reduces the wet thickness of the final composites. However, in this report, we show that addition of both PGA and GO to the fermentation medium shows a synergistic effect in increasing the wet thickness of the final BC composites. By gently agitating the solution, GO particles get entrapped into the BC network, as the formed pellicles can move below the liquid level and the GO particles suspended in the liquid can be entrapped into the BC network. Compared to other methods, this method achieves high toughness while using a mild and easily scalable fabrication procedure. These bacterially produced composites could be employed in the next generation of biodegradable structural high-performance materials, construction materials, and tissue engineering scaffolds (tendon, ligament, and skin) that require high toughness.

@en

Graphene oxide (GO) has recently been highlighted as a promising multipurpose two-dimensional material. However, free-standing graphene oxide films suffer from poor strength and flexibility, which limits scaling-up of production and lifetime structural robustness in applications. Inspired by the relationship between the organic and inorganic components of the hierarchical structure of nacre found in mollusk shells, we have fabricated self-assembled, layered graphene-based composite films. The organic phase of our composite is produced via environmentally friendly and economical methods based on bacterial production of γ-poly(glutamic acid) (PGA). Composite films made of GO, PGA, and divalent cations (Ca2+) were prepared through a slow solvent evaporation method at ambient temperature, resulting in a nacre-like layered structure. These biobased nanocomposite films showed impressive mechanical properties, which resulted from a synergistic combination of hydrogen bonding with the bacterially produced PGA and ionic bonding with calcium ions (Ca2+). The GO/PGA/Ca2+ composite films possessed a high strength of 150 ± 51.9 MPa and a high Young's modulus of 21.4 ± 8.7 GPa, which represents an increase of 120% and over 70% with respect to pure GO films. We provide rational design strategies for the production of graphene-based films with improved mechanical performance, which can be applied in filtration purification of wastewater in the paper, food, beverage, pigment, and pharmaceuticals industries, as well as for manufacturing of functional membranes and surface coatings.

@en

AAA+ proteases are degradation machines that use ATP hydrolysis to unfold protein substrates and translocate them through a central pore toward a degradation chamber. FtsH, a bacterial membrane-anchored AAA+ protease, plays a vital role in membrane protein quality control. How substrates reach the FtsH central pore is an open key question that is not resolved by the available atomic structures of cytoplasmic and periplasmic domains. In this work, we used both negative stain TEM and cryo-EM to determine 3D maps of the full-length Aquifex aeolicus FtsH protease. Unexpectedly, we observed that detergent solubilization induces the formation of fully active FtsH dodecamers, which consist of two FtsH hexamers in a single detergent micelle. The striking tilted conformation of the cytosolic domain in the FtsH dodecamer visualized by negative stain TEM suggests a lateral substrate entrance between the membrane and cytosolic domain. Such a substrate path was then resolved in the cryo-EM structure of the FtsH hexamer. By mapping the available structural information and structure predictions for the transmembrane helices to the amino acid sequence we identified a linker of ~20 residues between the second transmembrane helix and the cytosolic domain. This unique polypeptide appears to be highly flexible and turned out to be essential for proper functioning of FtsH as its deletion fully eliminated the proteolytic activity of FtsH.

@en

Ocean acidification is a threat to the net growth of tropical and deep-sea coral reefs, due to gradual changes in the balance between reef growth and loss processes. Here we go beyond identification of coral dissolution induced by ocean acidification and identify a mechanism that will lead to a loss of habitat in cold-water coral reef habitats on an ecosystem-scale. To quantify this, we present in situ and year-long laboratory evidence detailing the type of habitat shift that can be expected (in situ evidence), the mechanisms underlying this (in situ and laboratory evidence), and the timescale within which the process begins (laboratory evidence). Through application of engineering principals, we detail how increased porosity in structurally critical sections of coral framework will lead to crumbling of load-bearing material, and a potential collapse and loss of complexity of the larger habitat. Importantly, in situ evidence highlights that cold-water corals can survive beneath the aragonite saturation horizon, but in a fundamentally different way to what is currently considered a biogenic cold-water coral reef, with a loss of the majority of reef habitat. The shift from a habitat with high 3-dimensional complexity provided by both live and dead coral framework, to a habitat restricted primarily to live coral colonies with lower 3-dimensional complexity represents the main threat to cold-water coral reefs of the future and the biodiversity they support. Ocean acidification can cause ecosystem-scale habitat loss for the majority of cold-water coral reefs.

@en

Abstract: In the study of micro-scale biological flows, velocimetry methods based on passive tracers, such as micro-PIV and micro-PTV, are well established to characterize steady flows. However, these methods become inappropriate for measuring unsteady flows of small amplitude, because, on these scales, the motion of passive tracers cannot be distinguished from Brownian motion. In this study, we use optical tweezers (OTs) in combination with Kalman filtering, to measure unsteady microscopic flows with high temporal accuracy. This method is referred to as optical tweezers-based velocimetry (OTV). The OTV method measures the nanometric displacements of a trapped bead, and predicts the instantaneous velocity of the flow by employing a Kalman filter. We discuss the accuracy of OTV in measuring unsteady flows with 1.5–70 μ m s^{- 1} amplitudes and 10–90 Hz frequencies. We quantify how the bead size and the laser power affect the velocimetry accuracy, and specify the optimal choices for the bead size and laser power to measure different unsteady flows. OTV accurately measures unsteady flows with amplitudes as small as 3–6 μ m s^{- 1}. We compare the accuracy of OTV and micro-PTV, and characterize the flow regime for which OTV outperforms micro-PTV. We also demonstrate the robustness of OTV by measuring the unsteady flow created by the cilia of green alga Chlamydomonas reinhardtii, and comparing with numerical predictions based on Stokes equations. An open-source implementation of the OTV software in Matlab is available through the 4TU.Centre for Research Data. Graphic abstract: [Figure not available: see fulltext.].

@en

The flagella of Chlamydomonas reinhardtii possess fibrous ultrastructures of a nanometer-scale thickness known as mastigonemes. These structures have been widely hypothesized to enhance flagellar thrust; however, detailed hydrodynamic analysis supporting this claim is lacking. In this study, we present a comprehensive investigation into the hydrodynamic effects of mastigonemes using a genetically modified mutant lacking the fibrous structures. Through high-speed observations of freely swimming cells, we found the average and maximum swimming speeds to be unaffected by the presence of mastigonemes. In addition to swimming speeds, no significant difference was found for flagellar gait kinematics. After our observations of swimming kinematics, we present direct measurements of the hydrodynamic forces generated by flagella with and without mastigonemes. These measurements were conducted using optical tweezers, which enabled high temporal and spatial resolution of hydrodynamic forces. Through our measurements, we found no significant difference in propulsive flows due to the presence of mastigonemes. Direct comparison between measurements and fluid mechanical modeling revealed that swimming hydrodynamics were accurately captured without including mastigonemes on the modeled swimmer's flagella. Therefore, mastigonemes do not appear to increase the flagella's effective area while swimming, as previously thought. Our results refute the longstanding claim that mastigonemes enhance flagellar thrust in C. reinhardtii, and so, their function still remains enigmatic.

@en

The impressive mechanical properties of natural composites, such as nacre, arise from their multiscale hierarchical structures, which span from nano- to macroscale and lead to effective energy dissipation. While some synthetic bioinspired materials have achieved the toughness of natural nacre, current production methods are complex and typically involve toxic chemicals, extreme temperatures, and/or high pressures. Here, the exclusive use of bacteria to produce nacre-inspired layered calcium carbonate-polyglutamate composite materials that reach and exceed the toughness of natural nacre, while additionally exhibiting high extensibility and maintaining high stiffness, is introduced. The extensive diversity of bacterial metabolic abilities and the possibility of genetic engineering allows for the creation of a library of bacterially produced, cost-effective, and eco-friendly composite materials.

@en

Bacterial biofilms are three-dimensional networks of cells entangled in a self-generated extracellular polymeric matrix composed of proteins, lipids, polysaccharides, and nucleic acids. Biofilms can establish themselves on virtually any accessible surface and lead to varying impacts ranging from infectious diseases to degradation of toxic chemicals. Biofilms exhibit high mechanical stiffness and are inherently tolerant to adverse conditions including the presence of antibiotics, pollutants, detergents, high temperature, changes in pH, etc. These features make biofilms resilient, which is beneficial for applications in dynamic environments such as bioleaching, bioremediation, materials production, and wastewater purification. We have recently described an easy and cost-effective method for 3D printing of bacteria and have extended this technology for 3D printing of genetically engineered Escherichia coli biofilms. Our 3D printing platform exploits simple alginate chemistry for printing of a bacteria-alginate bioink mixture onto calcium-containing agar surfaces, resulting in the formation of bacteria-encapsulating hydrogels with varying geometries. Bacteria in these hydrogels remain intact, spatially patterned, and viable for several days. Printing of engineered bacteria to produce inducible biofilms leads to formation of multilayered three-dimensional structures that can tolerate harsh chemical treatments. Synthetic biology and material science approaches provide the opportunity to append a wide range of useful functionalities to these 3D-printed biofilms. In this article, we describe the wide range of future applications possible for applying functional 3D-printed biofilms to the construction of living biofilm-derived materials in a large-scale and environmentally stable manner.

@en