The sustainable development of groundwater resources in arid and semi-arid regions is a challenging task hindered by climate change and human activities. The rational utilization and management of groundwater resources is, therefore, dependent on an understanding of the influences of human and climatic factors on the spatial distribution of groundwater resources and their change over time. The thick Quaternary aquifers in the Yinchuan Basin, China were used herein as an example of how to quantitatively assess spatial and temporal trends in groundwater resources in response to human activities and climate change. A 3D transient groundwater flow model was constructed and used to simulate the evolution and spatial variability of hydrogeological processes from 1990 to 2020. By subsequently applying regime shift detection and correlation analysis to the simulation results, we found that: 1) groundwater storage was continuously depleted over the 30-year period, reaching a cumulative depletion of 1.89×10⁹ m³; 2) human activities were mainly responsible for variations in regional hydrogeological processes for a period of up to 30 years. Climate only affected short-term interannual fluctuations in groundwater storage; 3) human activities (e.g., river water diversion and groundwater abstractions) were the decisive factors causing a continuous reduction of groundwater resources. A policy-driven reduction in water diversion from the Yellow River directly led to a significant drop in groundwater storage, which had a consequent effect on surface water and groundwater interactions and altered agricultural irrigation patterns (crop patterns and irrigation methods); 4) the amount of groundwater recharge from the Yellow River and local lakes increased from 1990 to 2020, whereas the discharge of groundwater to the Yellow River and lakes decreased.

@en

Over the past decades, Floating Offshore Wind Turbine (FOWT) has gained increasing attention in wind engineering due to the rapidly growing energy demands. However, difficulties in turbine maintenance will increase due to the harsh operational conditions. Fault diagnosis techniques play a crucial role to enhance the reliability of FOWTs and reduce the cost of offshore wind energy. In this paper, a novel data-driven fault diagnosis method using regularized dynamic canonical correlation analysis (RDCCA) and Fisher discriminant analysis (FDA) is proposed for FOWTs. Specifically, to overcome the collinearity problem that exists in measured process data, dynamic canonical correlation analysis with a regularization scheme, is developed to exploit the relationship between input and output signals. Then, the residual signals are generated from the established RDCCA model for fault detection. To further classify the fault type, an FDA model is trained from the residual signals of different training faulty data sets. Simulations on a FOWT baseline model based on the widely used National Renewable Energy Laboratory FAST simulator are carried out to demonstrate the feasibility and efficacy of the proposed fault detection and classification method. Results have shown many salient features of the proposed method with potential applications in FOWTs.

@en

Currently, the offshore wind turbine has become a hot research area in the wind energy industry. Among different offshore wind turbines, floating offshore wind turbine (FOWT) can harvest abundant wind energy in deepwater areas. However, the harsh working environment will dramatically increase the maintenance cost and downtime of FOWTs. Wind turbine fault diagnosis is being regarded as an indispensable system for maintenance issues. Owing to the complexity of FOWT, it imposes an enormous challenge for effective fault diagnosis. This paper develops a novel FOWT fault diagnosis method based on a stacked denoising autoencoder (SDAE). First, a sliding window technique is adopted for time-series data to preserve temporal information. Then, SDAE is employed to extract the features from high-dimensional data. Based on the extracted features from SDAE, a classifier using multilayer perceptrons (MLP) is developed to determine the health status of the FOWT. To verify the performance of the proposed method, a FOWT simulation benchmark based on the National Renewable Energy Laboratory (NREL) FAST simulator is employed. Results show the superior performance of the proposed method by comparison with other relevant methods.

@en

In this article, a novel data-driven fault diagnosis method by combining deep canonical variate analysis and Fisher discriminant analysis (DCVA-FDA) is proposed for complex industrial processes. Inspired by the recently developed deep canonical correlation analysis, a new nonlinear canonical variate analysis (CVA) called DCVA is first developed by incorporating deep neural networks into CVA. Based on DCVA, a residual generator is designed for the fault diagnosis process. FDA is applied in the feature space spanned by residual vectors. Then, a Bayesian inference classifier is performed in the reduced dimensional space of FDA to label the class of process data. A continuous stirred-tank reactor and an industrial benchmark of the Tennessee Eastman process are carried out to test the performance of DCVA-FDA fault diagnosis. The experimental results demonstrate that the proposed DCVA-FDA fault diagnosis is able to significantly improve the fault diagnosis performance when compared to other methods also examined in this article.

@en

Floating Offshore Wind Turbines (FOWTs) operate in the harsh marine environment with limited accessibility and maintainability. Not only failures are more likely to occur than in land-based turbines, but also corrective maintenance is more expensive. In the present study, a mixed model and signal-based Fault Diagnosis (FD) architecture is developed to detect and isolate critical faults in FOWTs. More specifically, a model-based scheme is developed to detect and isolate the faults associated with the turbine system. It is based on a fault detection and approximation estimator and fault isolation estimators, with time-varying adaptive thresholds to guarantee against false-alarms. In addition, a signal-based scheme is established, within the proposed architecture, for detecting and isolating two representative mooring lines faults. For the purpose of verification, a 10MW FOWT benchmark is developed and its operating conditions, which contains predefined faults, are simulated by extending the high-fidelity simulator. Based on it, the effectiveness of the proposed architecture is illustrated. In addition, the advantages and limitations are discussed by comparing its fault detection to the results delivered by other approaches. Results show that the proposed architecture has the best performance in detecting and isolating the critical faults in FOWTs under diverse operating conditions.@en

Principal component analysis (PCA) and its modified methods have been widely applied in industrial process monitoring. In practice, industrial processes are with disparate characteristics, the process monitoring system should consider as many process characteristics as possible, such as dynamic and nonlinear characteristics. In this paper, a multi-feature extraction technique based on PCA is proposed for nonlinear dynamic process monitoring. The proposed method integrates dynamic inner PCA (DiPCA), PCA and kernel PCA (KPCA) methods through a serial structure to extract the dynamic, linear and nonlinear features among the process data. Along with the proposed method, the original data space is decomposed into several orthogonal subspaces, in which abnormal variations of different features can be monitored. For real-time process monitoring, a combined Hotelling's T² statistic based on the extracted multi-feature and a squared prediction error (SPE or Q) statistic are established. Case studies on a numerical example and the Tennessee Eastman process are carried out to demonstrate the superior process monitoring performance of the proposed method compared with other relevant methods.

@en