Urban drainage models (UDMs) are often used to manage urban flooding. However, these models generally involve many parameters to represent the underlying complex hydrodynamic processes. This results in significant challenges to achieving effective and robust model calibration especially with frequently limited observations, leading to unreliable model predictions. This paper makes the first attempt at UDM calibration using the Bayesian-based Ensemble Smoother (ES) method. Three ES variants are considered, that is, the primary ES, the versions with multiple data assimilation (ES-MDA) and iterative local update (ES-ILU). Two synthetic cases and one real-world application with up to 5,236 calibration parameters are tested. Results obtained show that: (a) both ES-MDA and ES-ILU can produce effective model calibration with ES-ILU outperforming ES-MDA in terms of both accuracy and uncertainty while ES exhibits limited performance; (b) for the real-world case, both the ES-MDA and ES-ILU methods provide better calibration results than the best-known solution manually obtained, (c) a minimum number of observations are required to enable an overall accurate model calibration (e.g., four and ten more monitoring sites are needed in the two synthetic cases); and (d) the model calibrated using an intense rainfall event is generally robust to make reliable predictions across different rainfall events while the model calibrated using less intense rainfall event does not perform well for more intense rainfall events. It was also found that ubiquitous parameter equifinality significantly hinders unique parameter identification even when overall accurate state estimates are obtained. This should be clearly understood in practical applications.

Urban sewer networks (SNs) are increasingly facing water quality issues as a result of many challenges, such as population growth, urbanization and climate change. A promising way to addressing these issues is by developing and using water quality models. Many of these models have been developed in recent years to facilitate the management of SNs. Given the proliferation of different water quality models and the promise they have shown, it is timely to assess the state-of-the-art in this field, to identify potential challenges and suggest future research directions. In this review, model types, modeled quality parameters, modeling purpose, data availability, type of case studies and model performance evaluation are critically analyzed and discussed based on a review of 110 papers published between 2010 and 2019. The review identified that applications of empirical and kinetic models dominate those of data-driven models for addressing water quality issues. The majority of models are developed for prediction and process understanding using experimental or field sampled data. While many models have been applied to real problems, the corresponding prediction accuracies are overall moderate or, in some cases, low, especially when dealing with larger SNs. The review also identified the most common issues associated with water quality modeling of SNs and based on these proposed several future research directions. These include the identification of appropriate data resolutions for the development of different SN models, the need and opportunity to develop hybrid SN models and the improvement of SN model transferability.

Hydraulic modeling of a foul sewer system (FSS) enables a better understanding of the behavior of the system and its effective management. However, there is generally a lack of sufficient field measurement data for FSS model development due to the low number of in-situ sensors for data collection. To this end, this study proposes a new method to develop FSS models based on geotagged information and water consumption data from smart water meters that are readily available. Within the proposed method, each sewer manhole is firstly associated with a particular population whose size is estimated from geotagged data. Subsequently, a two-stage optimization framework is developed to identify daily time-series inflows for each manhole based on physical connections between manholes and population as well as sewer sensor observations. Finally, a new uncertainty analysis method is developed by mapping the probability distributions of water consumption captured by smart meters to the stochastic variations of wastewater discharges. Two real-world FSSs are used to demonstrate the effectiveness of the proposed method. Results show that the proposed method can significantly outperform the traditional FSS model development approach in accurately simulating the values and uncertainty ranges of FSS hydraulic variables (manhole water depths and sewer flows). The proposed method is promising due to the easy availability of geotagged information as well as water consumption data from smart water meters in near future.

Real-time hydraulic modelling can be used to address a wide range of issues in a foul sewer system and hence can help improve its daily operation and maintenance. However, the current bottleneck within real-time FSS modelling is the lack of spatio-temporal inflow data. To address the problem, this paper proposes a new method to develop real-time FSS models driven by water consumption data from associated water distribution systems (WDSs) as they often have a proportionally larger number of sensors. Within the proposed method, the relationship between FSS manholes and WDS water consumption nodes are determined based on their underlying physical connections. An optimization approach is subsequently proposed to identify the transfer factor k between nodal water consumption and FSS manhole inflows based on historical observations. These identified k values combined with the acquired real-time nodal water consumption data drive the FSS real-time modelling. The proposed method is applied to two real FSSs. The results obtained show that it can produce simulated sewer flows and manhole water depths matching well with observations at the monitoring locations. The proposed method achieved high R², NSE and KGE (Kling-Gupta efficiency) values of 0.99, 0.88 and 0.92 respectively. It is anticipated that real-time models developed by the proposed method can be used for improved FSS management and operation.