This project was designed to understand the causes and mechanisms of bicycle disc brake noise and use that information to formulate and evaluate possible mitigation techniques. Brake noise was generated by a real bicycle running on a treadmill and recorded by microphone and laser vibrometer. Six independent variables, brake force, rotor thickness, front fork stiffness, weather conditions, spoke tension, and friction coefficient, were varied according to a one-quarter fractional factorial design. A finite element model of the rotor, pads, and calliper was also formulated and analysed. The results of these two methods, particularly the disc mode shapes and frequencies, suggest that doublet mode splitting and reconverging plays a role in noise generation and that changing the rotor mass or breaking its symmetry could interfere with such noise generation. Finally, of these mitigations, breaking disc symmetry proved the most fruitful, with noise magnitude reductions from 72% to 99%, depending on frequency.

@en

We previously presented a narrow-track tilting tricycle with a variable stability mechanism integrated between the swing arms that support a pair of rear wheels, in the so-called “delta” configuration, and with recumbent seating. We now examine adopting that variable stability mechanism to work on a tricycle with a split-parallelogram linkage between a pair of front wheels, in the so-called “tadpole” configuration, and with upright seating. It was fairly straightforward to allow for tilting by replacing the front wheel and fork with a split parallelogram comprising two paired A-arms and kingpins, controlling the motion of the two halves with a bell crank and two tie rods, and then varying the handling of the vehicle by moving the connection point of the tie rods on the bell crank, just as we did with the swing arms of the previous vehicle. We have also separated the two tasks of positioning the tie rod ends on the bell crank and enforcing symmetry of the tie rods. The former does not require much force and can be easily implemented with Bowden cables, but the latter does require large forces and is better implemented with a local rigid-bar linkage. Implementing decent Ackermann steering geometry, allowing for both large tilt and steer angles, and decoupling tilting from steering, however, proved to be quite a challenge, at least while we attempted to implement it with bar linkages. Fortunately, we discovered a 2006 paper by Prof Drstvenšek et al. describing a Bowden cable and cam system that looked promising. Finally, the resulting vehicle handles very nicely. When in “full bicycle” mode, it handles quite similar to the original bicycle that we had converted into the tricycle. When in “rigid tricycle” mode, it keeps the rider upright when stationary or when riding at a walking pace. In between these two extremes, it handles even better than the original bicycle in a slalom course and when slowly following a straight line.@en

Wobble, also known as speed wobble or shimmy, and the hazard it can cause to cyclists, is a well-known behavior of some bicycles. lt is a relatively high-frequency oscillation, 4-10 Hz. of the front fork and wheel assembly about the steering axis, and it can result in loss of control if left unaddressed. The importance of tyre mechanical properties, specifically conering stiffness, to the wobble motion of bicycles has been shown. Some tyres can make a bicycle more likely to wobble, while others can make the same bicycle less likely to wobble. There are only a few facilities in the world, however, capable of measuring these properties of bicycle tyres, and facilities for testing motorcycle and automobile tyres are not designed to work with bicycle wheels and/or are prohibitively expensive to use. We introduce and characterize an inexpensive, table-top device for measuring the necessary mechanical properties of bicycle tyres.@en

The potential advantages of tilting trikes have been tantalizing for years: they can lean like a bike so that they do not have to be low, wide, or slow in turns; and they can keep the rider upright like a trike when stopped or going slow. Implementing this functionality, however, has been somewhat problematic. Many tilting trikes have been built in which the extra wheel only offers some redundant traction, in the case of inconsistent friction with the road surface. Some have been built with a so-called ''tilt-lock', in which the third wheel can also act as a kickstand to hold the trike rigid when stopped. A few tilting trikes have been built with sophisticated sensors, actuators, and control algorithms to assume the proper tilt angle in every situation, and the motorcycle press breathlessly announces the latest patent filings in this area from major motorcycle manufacturers. @en