In this work, the accuracy of the Doppler beam-swinging (DBS) technique for wind measurements is studied using an imaging radar-the turbulent eddy profiler (TEP) developed by the University of Massachusetts, with data collected in summer 2003. With up to 64 independent receivers, and using coherent radar imaging (CRI), several hundred partially independent beams can be formed simultaneously within the volume defined by the transmit beam. By selecting a subset of these beams, an unprecedented number of DBS configurations with varying zenith angle, azimuth angle, and number of beams can be investigated. The angular distributions of echo power and radial velocity obtained by CRI provide a unique opportunity to validate the inherent assumption in the DBS method of homogeneity across the region defined by the beam directions. Through comparison with a reference wind field, calculated as the optimal uniform wind field derived from all CRI beams with sufficient signal-to-noise ratio (SNR), the accuracy of the wind estimates for various DBS configurations is statistically analyzed. It is shown that for a three-beam DBS configuration, although the validity of the homogeneity assumption is enhanced at smaller zenith angles, the rootmean-square (RMS) error increases because of the ill-conditioned matrix in the DBS algorithm. As expected, inhomogeneities in the wind field produce large bias for the three-beam DBS configuration for large zenith angles. An optimal zenith angle, in terms of RMS error, of approximately 9°-10° was estimated. It is further shown that RMS error can be significantly reduced by increasing the number of off-vertical beams used for the DBS processing.@en

This paper highlights recent results obtained with the Turbulent Eddy Profiler (TEP), which was developed by the University of Massachusetts. This unique 915-MHz radar has up to 64 spatially separated receiving elements, each with an independent receiver. The calibrated raw data provided by this array could be processed using sophisticated imaging algorithms to resolve the horizontal structures within each range gate. After collecting all of the closely spaced horizontal slices, the TEP radar can produce three-dimensional images of echo power, radial velocity, and spectral width. From the radial velocity measurements, it is possible to estimate the three-dimensional wind with high horizontal and vertical resolution. Given the flexibility of the TEP system, various array configurations are possible. In the present work exploitation of the flexibility of TEP is attempted to enhance the rejection of clutter from unwanted biological targets. From statistical studies, most biological clutter results from targets outside the main imaging field of view, that is, the sidelobes and grating lobes (if they exist) of the receiving beam. Because the TEP array's minimum receiver separation exceeds the spatial Nyquist sampling requirement, substantial possibilities for grating-lobe clutter exist and are observed in actual array data. When imaging over the transmit beam volume, the receiving array main lobe is scanned over a ±12.5° region. This scanning also sweeps the grating lobes over a wide angular region, virtually guaranteeing that a biological scatterer outside of the main beam will appear somewhere in the imaged volume. This paper focuses on suppressing pointlike targets in the grating-lobe regious. With a subtle change to the standard TEP array hardware configuration, it is shown via simulations and actual experimental observations (collected in June 2003) that adaptive beamforming methods can subsequently be used to significantly suppress the effects of point targets on the wind field estimates. These pointlike targets can be birds or planes with strong reflectivity. By pointlike the authors mean its appearance is a distinct point (up to the imaging resolution) in the images. The pointlike strong reflectivity signature exploits the capability of adaptive beamforming to suppress the interference using the new array configuration. It should be noted that this same array configuration does not exhibit this beneficial effect when standard Fourier beamforming is employed.@en

For many years, spatial and temporal inhomogeneities in precipitation fields have been studied using scanning radars, cloud radars, and disdrometers, for example. Each measurement technique has its own advantages and disadvantages. Conventional profiling radars point vertically and collect data while the atmosphere advects across the field of view. Invoking Taylor's frozen turbulence hypothesis, it is possible to construct time-history data, which are used to study the structure and dynamics of the atmosphere. In the present work, coherent radar imaging is used to estimate the true three-dimensional structure of the atmosphere within the field of view of the radar. The 915-MHz turbulent eddy profiler radar is well suited for imaging studies and was used in June 2003 to investigate the effects of turbulence on the formation of rain. The Capon adaptive algorithm was implemented for imaging and clutter rejection purposes. In the past several years, work by the authors and others has proven the Capon method to be effective in this regard and to possess minimal computational burden. A simple but robust filtering procedure is presented whereby echoes from precipitation and clear-air turbulence can be separated, facilitating the study of their interaction. By exploiting the three-dimensional views provided by this imaging radar, it is shown that boundary layer turbulence can have either a constructive or destructive effect on the formation of precipitation. Evidence is also provided that shows that this effect can be enhanced by updrafts in the wind field.

@en

A combination of pulse pair processing and beamforming techniques referred as pulse beamforming (PPB) for estimating velocity and spectral width using beamforming techniques was discussed. A statistical investigation into the applicability of Capron and fourier PPB techniques for high-resolution estimation of the wind and reflectivity field maps was also carried out. The pulse pair processing was extended to the beamformed imaging systems by using reflectivity derived weight vectors to estimate the pulse pair parameters for both velocity and spectral width estimates. By numerical simulation, the new technique provided robust and computationally efficient estimates of the spectral moments.@en