The HIsarna off-gas system wall is a cooling jacket made of cooling pipes arranged in the radial direction and in a circular pattern. Part of the off-gas system cooling pipes are isolated using a low-thermal-conductivity refractory material to protect the cooling pipe from melting and thermal stresses. During long runs and due to thermomechanical stresses, the refractory material is lost, and its thickness is reduced. It is possible to measure the thickness of the refractory layer only during shutdown, which is a disadvantage during long runs. The aim is to investigate the possibility of predicting the thickness of the refractory material by using other parameters that are possible to measure during the operation. A combination of FEM and CFD modeling is used to develop a methodology for detailed wall modeling and refractory material loss prediction. Finite element method (FEM) analysis is used to obtain the thermal properties of the wall using detailed geometries for variable refractory thickness. The obtained properties are then used to build CFD models to study the effect of refractory thickness on wall heat loss, temperature and composition profiles. The proposed procedure is validated against the plant measurement, and according to the findings, it is possible to relate the wall thickness to measured parameters such as heat loss through the walls, temperature and carbon conversion. @en

In this paper a CFD analysis of HIsarna off-gas system for post combustion of CO-H2-carbon particle mixture is presented to evaluate the effect of different sub-models and parameters on the accuracy of predictions and simulation time. The effects of different mesh type, mesh grid size, radiation models, turbulent models, kinetic mechanism, turbulence chemistry interaction models, including and excluding gas-solid reactions, number of reactive solid particles are investigated in detail. Based on the accuracy of the predictions and agreement with counterpart measured values, the best combination is selected and conclusions are derived. It was found that radiation and turbulence chemistry interaction model have a major effect on the temperature and composition profile prediction along the studied off-gas system, compared to the variations in other models. The effect of these two models becomes even more evident when the temperature and fuel content of the flue gas are high.@en

Within the steelmaking industry, a large amount of zinc-bearing waste is produced which cannot be effectively treated through integrated steel mills. Concurrently, zinc smelters generate waste residues containing significant amounts of iron and zinc which are stored or landfilled. The zinc concentration of iron and steelmaking residues inhibits its recycling to the blast furnace but is insufficient to be sent directly to the zinc producers. Consequently, a means of up-concentration is required. The pilot HIsarna ironmaking furnace has shown potential for processing secondary iron-bearing resources. Furthermore, zinc can be concentrated in the off-gas flue dust, providing an enriched input for zinc smelters. The potential recyclability of blast furnace (BF) and basic oxygen furnace (BOF) dust and ‘goethite’ residue from the zinc industry has been studied. The input materials have been comprehensively characterized and their reduction–vaporization behavior, has been investigated. Individual samples were tested at temperatures of up to 1300 °C. Here, it was shown that minimal reduction of iron and volatilization of zinc occurred in the goethite and BOF samples. Conversely, even at 1000 °C, the BF dust showed complete reduction of iron and removal of zinc within 30 min. This was due to its high carbon content (40 wt%) which can act as a reductant. Consequently, mixtures of BOF dust and goethite with BF dust were studied. It has been shown that mixtures of 30:70 BF dust to goethite and 20:80 BF dust to BOF dust are suitable for recovering zinc to the gas phase and fully reducing the contained iron. Graphical Abstract: [Figure not available: see fulltext.]

@en

Galvanized steel scrap flow and injection into the HIsarna reactor are investigated using discrete element method (DEM). The scrap particle is fed into the reactor through an inclined chute and hits the slag surface where the zinc content is evaporated and solid particles melt. A DEM model is setup and validated using experimental data obtained from the exact plant-scale chute geometry and scrap particles. Using the DEM model, the effect of chute inclination, injection elevation, injection mode (batch and continuous), batch size, and flowrate on particle distribution and exerted pressure on the slag surface are investigated. It is found that continuous mode of injection is the most suitable method to increase the spread of particles and also to reduce the exerted pressure on the slag surface. Placing dent-like obstacles at the tip of the chute significantly increases the impact area, especially for batchwise injection, thus reducing force and pressure on the slag surface that minimizes the risk of liquid splash. Larger particle impact area is also beneficial to obtain higher zinc evaporation rate from particle surface and also to minimize the slag surface temperature disturbance.

@en

The HIsarna process is a new and breakthrough smelting reduction process for hot metal (liquid iron) production from iron ores and coal directly fed into the reactor. The flue gas from the main reactor enters the off-gas system containing small amounts of H₂, CO and carbon particles which need to be removed before further treatment by post combustion oxygen injection. A three-dimensional Computational Fluid Dynamics (CFD) simulation of the HIsarna off-gas system is performed and validated using a detailed reaction mechanism and kinetic data for post-combustion of a CO–H₂ mixture and carbon particles. Using the validated model, a series of simulations were performed to investigate the effect of water quenching and post combustion oxygen injection. It was found that water quenching can significantly reduce the off-gas temperature. It is also possible to reduce oxygen injection during operations where inlet CO content of the off-gas system is low.

@en

A three-dimensional computational fluid dynamics (CFD) model for the HIsarna off-gas system is set up and validated by real plant data. In the model detailed reaction mechanism and kinetic data for post-combustion of CO-H2 mixture and carbon particles are incorporated. The results are presented and discussed in another study (Part 1) by the same authors. In the present paper, the focus will be on geometry modification of the off-gas system and the effects on the operating parameters. The effect of this modification on heat loss, temperature profile, carbon conversion and gaseous phase composition across the off-gas system is investigated. It is shown that the modified geometry leads to a higher heat loss through the reflux chamber walls which can change the temperature profile and consequently species composition. The modified geometry also offers possibility of higher CO-H2 mixture and carbon particles conversion rate and reduce unwanted emission from the reflux chamber.

@en

HIsarna is a novel ironmaking process with great raw materials versatility that is attractive for various secondary resources. Among the materials that can be recycled, there is steel scrap which is fed to the furnace bath through an inclined chute. The velocity distribution of the scrap particles along the chute affects the particles’ distribution on the liquid slag and, thereupon, the efficient operation of the reactor. In this study, the flow of steel scrap particles along an inclined chute with the same dimensions as those of the actual chute of the HIsarna plant is investigated experimentally and numerically. The simulations are validated using chute tip velocity and mass fractions collected at the different compartments of a sampling device. Translational and angular velocity distributions along and across the chute are reported, and the effect of different parameters are investigated. The impact of the shape of the particles on the simulation process is found to be negligible. The angular velocity distribution in cross-sections of the chute exhibited a V-shaped orientation, whereas the translational velocity displayed similar values across the cross-sections. Moreover, translational velocity appeared to increase with increasing inclination angles, whereas angular velocity increased with decreasing batch size.

@en

HIsarna reactor is characterized by a high raw materials versatility and is therefore attractive for processing secondary iron sources. Among the materials that can be recycled through HIsarna, zinc-bearing material has drawn a special attention. Based on the plant data, once dust-containing Zinc was injected into the main reactor, a final collected dust with a zinc content of 16% was achieved which opened up possibilities of higher enrichment for direct reuse in Zn smelting as a secondary source and an alternative for Zn ore (the primary source). However Zn vapor can react with iron oxide to form zinc ferrite (ZnFe₂O₄), which is an undesired product. Hence, the main focus of this study is to minimize the formation of ZnFe₂O using thermodynamic (FactSage) and computational fluid dynamic tools. After detecting regions with high potential of ZnFe₂O₄ formation, proper geometrical and operational modifications of the off-gas system is proposed to minimize the formation of zinc ferrite.

@en