The Arctic is a recent focal point of the marine and offshore industries. Winterization is required for safe and efficient operations in these harsh cold environments. A riskbased approach to winterization was recently proposed to provide a quantitative way of determining the need for winterization and its appropriate level. To further validate and enhance this approach, it has been applied to a new ice-class passenger ferry design, which will operate in a particular area of the North Atlantic. This location is ideal for the application with low temperatures, strong wind, and high waves. To facilitate this application and eliminate some limitations of the proposed approach, this article proposes a generic framework of risk-based winterization. Results from this article validated the effectiveness and feasibility of using risk-based winterization on vessel designs.@en

Development of natural resources in harsh environments presents significant technical and logistical challenges. An industrial workshop on "safety and integrity management of operations in harsh environments" was organized by the safety and risk engineering group at Memorial University of Newfoundland to bring together industrial practitioners, regulatory authorities, and research and development institutions to identify the safety and integrity challenges in harsh environments, share experience, and develop a roadmap for desired solutions. This article summarizes the lessons learned from the workshop on safety issues in harsh environments. The workshop identified that there are safety challenges regarding construction and operation including a lack of detailed standards, optimization with respect to winterization, and data scarcity. The remoteness of operations in harsh environments is an additional challenge. Finally, human factors add another set of challenges that arise from the physical and psychological behavior of personnel in harsh and remote environments.

@en

Over the past eight decades the ice-infested Northern Sea Route (NSR) has been steadily developed although historically it has been of little interest to commercial shipping companies. However, the shorter routes, more open waters, and the increasing demand for shipping have caused shipping companies to reconsider shipping along these routes. The NSR is now part of an overall world transportation system. However, a key problem of shipping in Arctic environments is the extreme low temperatures encountered and sea ice during most of the year. The American Bureau of Shipping (ABS) has provided some guidance for shipping along the Arctic sea routes with winterization of the Arctic going vessel as a suggested requirement. The technology and level of winterization is determined by the design service temperature (DST) estimated by the lowest mean daily average temperature (MDAT) over at least a 20-year period for the intended geographical area and season of operation. Systems that are more susceptible to the lower temperatures have another temperature which ABS designates as the Minimum Anticipated Temperature (MAT). However, the suitability of that value with respect to a risk based assessment on a vessel and its systems is questionable. For a modern risk-based approach to winterization, knowledge of the magnitude and frequency of occurrence for a given duration are prerequisites. This paper presents a new and more rational approach to estimate the DST or MAT. The approach is based on the set of Temperature-Duration-Frequency (TDF) curves developed for a given climate station. For this study, the Arctic was divided into four regions. Annual extreme low temperatures of durations 1, 3, 6, 12, 24, 36, 48, 72, 96, 120, 144, and 168 hours were extracted from the last 20 years of historical record from three to four representative stations in each region. Magnitudes of low temperatures were then estimated from the data for return periods ranging from 2 to 100 years. These estimates are then used to construct the TDF curves that provide estimates of the magnitude of extreme low temperatures for a given return period, for various durations of practical interest. It is proposed that the 100-year return period 1-hour duration lowest extreme temperature be used as the estimate of the MAT. The proposed approach addresses the drawbacks of the current approach and provides a practical estimate of the DST or MAT for risk-based winterization decisions.

@en

Because the oil and gas industry has an increasing interest in the hydrocarbon exploration and development in the Arctic regions, it becomes important to design exploration and production facilities that suit the cold and harsh operating conditions. In addition to well-established minimum class requirements for hull strengthening, winterization should be considered as a priority measure early in the design spiral for vessels operating in the Arctic environments. The development of winterization strategies is a challenging task, which requires a robust decision support approach. This article proposes a risk-based approach for the selection of winterization technologies and determination of winterization levels or requirements on a case-by-case basis. Temperature data are collected from climatology stations located in the Arctic regions. Loading scenarios are defined by statistical analysis of the temperature data to obtain probabilistic distributions for the loadings. Risk values are calculated under different loading scenarios. Based on the risk values, appropriate winterization strategies can be determined. A case study is used to demonstrate how the proposed approach can be applied to the identification of heating requirements for gangways.@en

Vast reserves in the Arctic and sub-Arctic regions have attracted interest of the oil and gas industry. However, oil and gas development in harsh environments faces significant technical and logistical challenges. A workshop on "safety and integrity management of operations in harsh environments" was organized by the Safety and Risk Engineering Group at Memorial University of Newfoundland focusing on main aspects of asset integrity. The event featured representatives from industry, regulatory authorities, and research and development institutions. Participants shared experience and lessons learned, and together developed a roadmap for achieving desired solutions. This paper briefly reviews the lessons learned from the two-day workshop and shares recent developments and applications of risk-based approaches to degradation modeling, integrity assessment, and inspection and maintenance decision-making in harsh environments. The recently developed novel approach of risk-based winterization method is introduced. This approach helps to analyze how much winterization is sufficient to address local and regional weather loading considering operating envelop and criticality of the components or the system. A case study from the Arctic region is used for discussion.@en

Because the oil and gas industry has an increasing interest in the hydrocarbon exploration and development in the Arctic regions, it becomes important to design exploration and production facilities that suit the cold and harsh operating conditions. In addition to well-established minimum class requirements for hull strengthening, winterization should be considered as a priority measure early in the design spiral for vessels operating in the Arctic environments. The development of winterization strategies is a challenging task, which requires a robust decision support approach. This article proposes a risk-based approach for the selection of winterization technologies and determination of winterization levels or requirements on a case-by-case basis. Temperature data are collected from climatology stations located in the Arctic regions. Loading scenarios are defined by statistical analysis of the temperature data to obtain probabilistic distributions for the loadings. Risk values are calculated under different loading scenarios. Based on the risk values, appropriate winterization strategies can be determined. A case study is used to demonstrate how the proposed approach can be applied to the identification of heating requirements for gangways.@en

Development of natural resources in harsh environments presents significant technical and logistical challenges. An industrial workshop on "safety and integrity management of operations in harsh environments" was organized by the safety and risk engineering group at Memorial University to bring together industrial practitioners, regulatory authorities, and research and development institutions to identify the safety and integrity challenges in harsh environments, share experience and develop a roadmap for desired solutions. This article summarizes the lessons learned from the workshop on safety issues in harsh environments. The workshop identified that there are safety challenges regarding construction and operation including a lack of detailed standards, optimization with respect to winterization, and data scarcity. The remoteness of operations in harsh environments is an additional challenge. Finally, the human factors add another set of challenges that arise from the physical and psychological behavior of plant personnel in harsh and remote environments.

@en