Aromatic micropollutants found in wastewater pose threats to human health, and it is necessary to remove them from wastewater. Cyclodextrin hydrogel is one of the most promising environmentally friendly materials for removing aromatic micropollutants from wastewater by means of adsorption. In this study, we have synthesized a cyclodextrin hydrogel designed to simultaneously adsorb a cationic dye (methylene blue, MB) and an endocrine-disrupting compound, EDC (bisphenol A, BPA) and provide insights into the design of adsorbents for multicomponent wastewater purification. Polymeric dextran-poly(acrylic acid)-β-cyclodextrin (Dex-PAA-CD) was prepared by the copolymerization of glycidyl methacrylate (GMA), methacrylate-substituted dextran (Dex-MA), acrylic acid, and vinyl-derivatized β-cyclodextrin (β-CD-MA). The adsorption of MB and BPA by the Dex-PAA-CD hydrogel presented short equilibrium time. The adsorption of MB and BPA was independent of each other, and their adsorption mechanisms were proved to be electronic interaction and cyclodextrin host-guest interaction, respectively. The maximum adsorption capacities of MB and BPA onto Dex-PAA-CD are determined to be 5.60 and 0.144 mmol/g by the Sips isotherm. The Dex-PAA-CD hydrogel retains a high adsorption capacity even after five adsorption/desorption cycles and demonstrates the feasibility of designing reusable adsorbents to remove multiple pollutants from wastewater.

A biocompatible Dex-MA/PAA hydrogel was prepared through copolymerization of glycidyl methacrylate substituted dextran (Dex-MA) with acrylic acid (AA), which was applied as the adsorbent to remove cationic dyes from aqueous solutions. Dex-MA/PAA hydrogel presented a fast adsorption rate and the removal efficiency of Methylene Blue (MB) and Crystal Violet (CV) reached 93.9% and 86.4%, respectively within one minute at an initial concentration of 50 mg L^-1. The adsorption equilibrium data fitted the Sips isotherm model well with high adsorption capacities of 1994 mg g^-1 for MB and 2390 mg g^-1 for CV. Besides, dye adsorption occurred efficiently over the pH range 3-10 and the temperature range 20-60 °C. Moreover, the removal efficiencies for MB and CV were still >95% even after five adsorption/desorption cycles which indicates the robust nature of the Dex-MA/PAA hydrogel and its potential as an eco-friendly adsorbent for water treatment.

Tungsten coatings were deposited on diamond particles by vacuum magnetron sputtering. The coated diamond particles were firstly heat treated at different temperatures, and diamond/copper (Cu) composites were fabricated by using a pressureless infiltration method afterwards. The influences of heat treatment on the microstructure and composition of tungsten based coating surface and diamond/copper composites were analysed. Notable differences were found in the microstructure with heating temperatures. Moreover, the tungsten based coating surface contained large quantities of oxidised tungsten, and the phase composition of the coatings varied within the range of tungsten–W ₂ C–WC as the heat treatment temperature increased. The fracture surface morphologies in the copper matrix composites reinforced with diamond particles with coatings were identically characterised with the presence of ductile fracture of matrix accompanied by dissociation of diamond particles from the matrix. The thermal conductivity (TC) and gas tightness behaviours of the diamond/copper composites were also explored. A maximum TC of 768 W m ⁻¹ K ⁻¹ and a fine gas tightness of 2.5 × 10-10 Pa m ³ /s were obtained with reinforcement of tungsten-coated diamond particles treated at 800 °C. The value of the interface thermal resistance between copper and diamond particles was also estimated and specifically discussed.

Chitosan has been used to cross-link poly(acrylic acid) to give three pH-sensitive hydrogels designed to control the release of the drugs amoxicillin and meloxicam. The extent of cross-linking and solution pH was found to dominate the swelling behavior of these hydrogels as shown by scanning electron microscopy and swelling time dependencies. The rates of release of amoxicillin and meloxicam from the loaded hydrogels increased with increase in pH consistent with the extent of hydrogen bonding between hydrogel components and between the hydrogel and the drugs being important determinants of release rate. Both the Korsemeyer-Peppas and Weibull models fitted release data consistent with drug release occurred through a combination of drug diffusion and hydrogel relaxation processes. These hydrogels appear to provide an ideal basis for controlled drug delivery systems.