This mini review explores the potential of visible light–driven bismuth vanadate (BiVO₄)-based photoanodes for removing trace organic pollutants from water. It highlights the advantages of using BiVO₄-based photoanodes over conventional UV-driven photoanodes in water treatment. The mechanism of reactive species generation through water oxidation is discussed. The review also highlights the role of sulfate and sulfite radicals in enhancing pollutant degradation. Furthermore, it evaluates how heterojunction formation improves the removal efficiency of BiVO₄-based photoanodes by reducing charge carrier recombination. Limited research on BiVO₄-based photoanodes for the simultaneous removal of multiple organic pollutants at low concentrations (<1 mg L⁻¹) from real wastewater is identified as a key knowledge gap. Addressing this gap could advance the application of BiVO₄-based photoanodes in photoelectrocatalytic-based advanced oxidation processes.

@en

The presence of organic micro-pollutants (OMPs) in wastewater treatment effluents is becoming a major threat to the water safety for aquatic and human health. Photo-electrocatalytic based advanced oxidation process (AOP) is one of the emerging and effective techniques to degrade OMPs through oxidative mechanism. This study investigated the application of heterojunction based BiVO4/BiOI photoanode for acetaminophen (40 μg L−1) removal in demineralized water. Photoanodes were fabricated by electrodeposition of BiVO4 and BiOI photocatalytic layers. Optical (UV–vis diffusive reflectance spectroscopy), structural (XRD, SEM, EDX) and opto-electronic (IPCE) characterization confirmed the successful formation of heterojunction for enhanced charge separation efficiency. The heterojunction photoanode showed incident photon to current conversion efficiency of 16% (λmax = 390 nm) at an external voltage of 1 V under AM 1.5 standard illumination. The application of the BiVO4/BiOI photoanode in the removal of acetaminophen at 1 V (external bias) vs Ag/AgCl under simulated sunlight showed 87% removal efficiency within the first 120 min compared to 66% removal efficiency of the BiVO4 photoanode. Similarly, combining BiVO4 and BiOI exhibited 57% increase in first order removal rate coefficient compared to BiVO4. The photoanodes also showed moderate stability and reusability by showing 26% decrease in overall degradation efficiency after three cycles of each 5 h experiment. The results obtained in this study can be considered as a stepping stone towards the effective removal of acetaminophen as an OMP present in wastewater.@en

In this research, photoelectrocatalytic (PEC) based advanced oxidation process (AOP) was studied for the removal of multiple OMPs through an oxidative mechanism. This study investigated the application of a BiVO4 photoanode in simultaneous removal of three selected OMPs: acetaminophen (ACT), benzotriazole (BTA) and propranolol (PRO). This study was carried out in demineralized water with a starting concentration of each organic micro-pollutant (OMP) at 45 μg L−1. In order to fabricate BiVO4 photoanodes, a facile and effective dip-coating method was used to deposit BiVO4 photocatalytic layers on fluorine doped tin oxide (FTO) substrate. UV–vis diffusive reflectance spectroscopy, x-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) confirmed the successful fabrication of porous BiVO4 photoanode having an absorbance edge at around 526 nm. The fabricated photoanode showed incident photon to current conversion efficiency (IPCE) of 9.23% (λmax=445 nm) under 1 Sun standard illumination. Application of the fabricated photoanodes for the simultaneous removal of ACT, PRO and BTA at an applied voltage of 1 V (vs Ag/AgCl) under solar simulated light resulted in 99% removal of both ACT and PRO, and 70% removal of BTA. The first order rate coefficients and half-life times of ACT and PRO were about three times higher than those of BTA.@en