The report examines the role of Standalone Microgrids (SMs) in electrification and emissions reduction, focusing on the comparison of HOMER Pro and iHOGA PRO+ software. It assesses these tools using 22 criteria and three case studies, highlighting differences in optimization results and the importance of selecting software based on specific requirements. Despite minor discrepancies in sizing, the comparison underscores each software’s strengths and weaknesses in designing efficient and cost-effective SMs. The main authors have identified the following 3 Key Takeaways from the report: HOMER PRO and iHOGA PRO+ are publicly available software tools for the microgrid optimization process during the microgrid pre-design phase. Task 18 has defined 22 criteria (quantitative and qualitative) to help software users evaluate which software tool fits better their needs. Based on the quantitative criteria, Task 18 has found that the simulation results from both software tools are equivalent, both when simulating an existing microgrid with real measurement data and when simulating a new microgrid from scratch. However, based on the qualitative criteria, both software tools have some uniqueness in terms of their features.@en

Electrolysis requires a high DC current at low voltage to produce hydrogen from water. Designing power converters for such a load requirement could be challenging while fulfilling the galvanic isolation needs. Therefore, prior knowledge of the electrolyzer's impact on the converter operation should be needed. In this context, this paper investigates the behavior of the Dual Active Bridge (DAB) converter when utilized for electrolysis. A MATLAB simulation of DAB with a 10 kW alkaline electrolyzer is developed. Several converter parameters, such as the phase shift angle, series inductance, peak and RMS currents, and voltage gain, are analyzed during electrolysis. Distinct operating behavior is observed from the analysis.@en

Reliable Power Electronic Systems (PES) are vital for enabling energy transition technologies of the future. Power hardware-in-the-Loop (PHIL) test bed can be used to validate such systems cost-effectively and time-efficiently. In general, the Real Time Digital Twin (RTDT) is a virtual representation of the PES and its operating environment that mimics its behavior in real-time to provide adequate flexibility to the test bed. The workflow of alternating between the prototype and twin, for instance, overcomes the dilemma of needing 100 % details (due to fast dynamics), but optimization during design choices requires cheap flexibility. In this paper, some use cases in applications of RTDT-based PHIL test bed such as fault tolerant converters, power electronic interface for green technologies, survivable all-electric ships, mission profile-based reliability testing, protection of multi terminal dc systems and reconfigurable hybrid ac-dc links is discussed. Furthermore, the co-simulation potential of real-time platforms is briefly described.@en

Power electronics converters (PEC) play a crucial role in interfacing renewable energy systems and electrolyzers to ensure a high production yield of green hydrogen. The design of such PEC is not straightforward due to the safety hazards of using multiple electrolyzer stacks and converter modules at industrial levels. Therefore, real-time simulations should be conducted to ensure the converter design satisfies all the requirements before deploying it on-site. This paper presents a real-time digital twin (RTDT) of a 10 kW dual-active bridge converter interfaced with an electrolyzer. OPAL-RT simulator (eHS toolbox) is used for RTDT. Finally, the voltage across the series inductance and current flowing through it are presented for the open-loop operation of DAB.@en

In recent years, the research interest in off-grid (standalone mode) and hybrid (capable of both standalone and grid-connected modes) charging systems for electric vehicles (EVs) has increased. The main reason is to provide a seamless charging infrastructure in urban and rural areas where the electrical grid is unreliable or unavailable so that EV adoption can be increased worldwide. In this regard, this article reviews the state-of-the-art architectures of the off-grid and hybrid charging systems and investigates their various subsystems, such as single or multiple energy sources, power electronics converters, energy storage systems, and energy management strategies. These subsystems should be optimally integrated and operated to achieve low-cost and efficient EV charging. Moreover, each subsystem is explored in detail to find the current status and technology trends. Furthermore, EV charging connectors, their power level, and standards for all kinds of EVs (ranging from one-wheeler to four-wheelers) are reviewed, and suggestions are discussed related to the non-standardization of charging plugs. Finally, conclusions show the continuous efforts of the researchers in improving the systems in various aspects, such as cost reduction, performance improvement, longevity, negative environmental effect, system size minimization, and efficient operation, and highlight challenges for both charging systems.@en